AEM Series 2 ECU part 30-6100 is a model-specific plug-in EMS documented for the 1993–1998 Toyota Supra twin-turbo. The AEM 30-6100 installation guide identifies the application and must be checked for exact equipment and wiring.
Connector reference
AEM's UEGO gauge integration table lists ECU pins B47 and B48 for lambda inputs 1 and 2 and B65 for sensor ground on 30-6100/6101. This is a limited interface reference, not a full connector pinout. Follow the specific application manual for remaining signals, orientation and electrical limits.
Configuration
AEM lists AEMTuner for Series 2 in its software archive. Base maps and software are starting points; confirm crank trigger, fuel and ignition hardware, sensor calibration and output assignments for the actual vehicle.
See the AEM manufacturer index. Sources reviewed 17 November 2026.
Connector pinout
A structured pinout covering all 40 positions of connector A and 80 positions of connector B, with redrawn wire-view diagrams, is on AEM EMS Series 2 30-6100 connector pinout. The schedules below are the manufacturer's tables from the installation manual for the 1993–1998 Toyota Supra 2JZ-GTE application.
Manufacturer 30-6100 connector schedules
From the AEM 30-6100 Series 2 installation manual, pages 11–14: all 40 A-connector and 80 B-connector positions are included. The manual identifies its connector diagram as the wire view. Vehicle functions describe the documented 1993–1998 Supra 2JZ-GTE loom; the AEM column describes this particular EMS. Some functions can be reassigned and equipment differs between automatic and manual cars. “Not used” and “Reserved” reproduce the manufacturer’s designation, rather than proving a vehicle cavity is physically empty.
The AEM table identifies 4A as a factory 12 V brake switch but says the available Switch 6 input must connect to ground. Confirm the actual vehicle and input wiring with AEM before connecting this circuit. The guide also documents differences from the Series 1 30-1100, so do not transfer this schedule to that ECU.
Connector A
| Pin | Supra 2JZ-GTE vehicle connection | AEM 30-6100 function | Direction | Manufacturer notes |
|---|---|---|---|---|
| 1A | Switched 12V at key on | Main Relay circuit | Input | Dedicated, activates Switch 1 input |
| 2A | Vehicle Speed Sensor | Car Speed | Input | PnP for VSS signal (MT)* |
| 3A | Kickdown switch | Switch 3 | Input | Available, switch must connect to GND |
| 4A | Brake switch input (12V) | Switch 6 | Input | Available, switch must connect to GND |
| 5A | --- | --- | --- | Not Used |
| 6A | Malfunction Indicator Lamp | LS10 | Output | Available, switched GND output (1.5A max) |
| 7A | Reverse indicator input, A/T only | ATPR (GEAR) | Input | PNP reverse input (auto only) |
| 8A | SDL (98 only) | --- | --- | Not Used |
| 9A | 2nd gear indicator input, A/T only | ATP2 (GEAR) | Input | PNP 2nd gear indicator (auto only) |
| 10A | 1st gear indicator input, A/T only | ATP1 (GEAR) | Input | PNP 1st gear indicator (auto only) |
| 11A | ABS to ABS and TRAC ECU | CAN1L | Output | Dedicated |
| 12A | OD1 to cruise control ECU | CAN1H | Output | Dedicated |
| 13A | TRC - To TRAC ECU | Reserved | --- | Reserved for future use |
| 14A | TRC+ To TRAC ECU | Reserved | --- | Reserved for future use |
| 15A | ELS for Idle up Diode | --- | --- | Not Used |
| 16A | LS7 (Tach out for climate control) | LS7 | Output | PnP for Tacho Out |
| 17A | TT For DATALINK connector | Injector 12 | Output | Available, P&H Injector driver 4A/1A |
| 18A | Trans mode selector sw (A/T only) | Switch 5 | Input | PnP for Manual trans mode (auto only) |
| 19A | TE2 to DATALINK connector | Injector 11 | Output | Available, P&H Injector driver 4A/1A |
| 20A | TE1 For DATALINK connector | --- | --- | Not Used |
| 21A | DI from Fuel Pump ecu | --- | --- | Not Used |
| 22A | Fuel pump control (FPC) | Coil 8 / LS8 | Output | PnP 0–5V FPC signal, not for use with relays |
| 23A | ACMG to A/C Magnetic clutch | LS6 | Output | PNP for A/C compressor relay |
| 24A | Main Relay Control | Main Relay (HS2) | Output | Dedicated, activates Main Relay with 12V |
| 25A | Trans mode light (A/T only) | ATIND (Coil7) | Output | PNP manual mode indicator (auto only) |
| 26A | EFI - to TRAC ECU | EFI-TRC | Input | Dedicated |
| 27A | EFI+ to TRAC ECU | EFI+TRC | Input | Dedicated |
| 28A | Over Drive Switch input (A/T only) | Switch 4 | Input | PNP for Overdrive input (auto only) |
| 29A | --- | Baro (ADCR12) | Input | Available, Spare 0–5V Sensor Input |
| 30A | --- | --- | --- | Not Used |
| 31A | +12V Power from main relay | +12V Switched | Both | Dedicated |
| 32A | --- | --- | --- | Not Used |
| 33A | +12V permanent battery backup power | Permanent +12V | Input | Dedicated, used to store internal datalog |
| 34A | A/C signal from A/C amplifier | ADCR11 | Input | PNP for Air Conditioning request switch |
| 35A | --- | HALLPWR | Output | +12V Output |
| 36A | --- | Injector 8 | Output | Spare P&H Injector 4A/1A |
| 37A | --- | --- | --- | Not Used |
| 38A | NEO to TRAC ECU | LS7 | --- | PnP for spare Tacho Out |
| 39A | VTO2 (98 only) | --- | --- | Not Used |
| 40A | VTO1 (98 only) | --- | --- | Not Used |
Connector B
| Pin | Supra 2JZ-GTE vehicle connection | AEM 30-6100 function | Direction | Manufacturer notes |
|---|---|---|---|---|
| 1B | Input Shaft Speed (B21) ground | Timing Ground | Output | Dedicated |
| 2B | --- | EGT 1 | Input | Jumper: 0–5V, thermistor or EGT pull up |
| 3B | VSS Ground | Timing Ground | Output | Dedicated |
| 4B | --- | EGT 2 | Input | Jumper: 0–5V, thermistor or EGT pull up |
| 5B | Cam Sensor 2 (G2) Ground | --- | --- | Not Used |
| 6B | Cam Sensor 1 (G1) Ground | Timing Ground | Output | Dedicated |
| 7B | Crank Sensor (NE) Ground | Timing Ground | Output | Dedicated |
| 8B | --- | EGT 3 | Input | Jumper: 0–5V, thermistor or EGT pull up |
| 9B | Auto Trans Sol No2 S2 (Auto only) | HS3 | Output | PNP Auto Trans sol #2 |
| 10B | Auto Trans Sol No1 S1 (Auto only) | HS4 | Output | PNP Auto Trans sol #1 |
| 11B | 5V Sensor Reference power | +5V Sensor | Output | Dedicated |
| 12B | A/T Sol No5 (Line Press, A/T only) | PW 1 | Output | PNP Auto line pressure |
| 13B | A/T Sol No4 (Engagement, A/T only) | PW 4 | Output | PNP Auto gear engagement speed |
| 14B | A/T Sol No3 (Converter, A/T only) | PW 3 | Output | PNP Auto Converter Lockup |
| 15B | Injector 6 | Injector 6 | Output | PnP Injector 6 (P&H 4A/1A driver) |
| 16B | Injector 5 | Injector 5 | Output | PnP Injector 5 (P&H 4A/1A driver) |
| 17B | Injector 4 | Injector 4 | Output | PnP Injector 4 (P&H 4A/1A driver) |
| 18B | Injector 3 | Injector 3 | Output | PnP Injector 3 (P&H 4A/1A driver) |
| 19B | Injector 2 | Injector 2 | Output | PnP Injector 2 (P&H 4A/1A driver) |
| 20B | Injector 1 | Injector 1 | Output | PnP Injector 1 (P&H 4A/1A driver) |
| 21B | Input Shaft Speed signal (Auto only) | Switch 2 | Input | Available Switch input |
| 22B | --- | --- | --- | Not Used |
| 23B | Tail Shaft Speed sensor (Auto only) | T4 (Spare Speed) | Input | PNP for Vehicle Speed with AT vehicles |
| 24B | Auto Trans Fluid Temp (Auto only) | ADCR14 | Input | Available 0–5V input, 2.2k pull up to 5V |
| 25B | Cam Sensor 2 (G2) Input | --- | --- | Not Used |
| 26B | Cam Sensor 1 (G1) input | Cam Sensor + | Input | Dedicated |
| 27B | Crank Sensor (NE) input | Crank Sensor + | Input | Dedicated |
| 28B | Sensor Ground | Sensor Ground | Output | Dedicated, Sensors only |
| 29B | DATALINK connector | IDLE7 | Output | PNP Idle control motor |
| 30B | --- | IDLE8 | Output | PNP Idle control motor |
| 31B | Auto Trans Sol No5 (SLT+, Auto only) | +12V Switched | Output | PNP Auto trans line pressure |
| 32B | Idle 4 | IDLE4 | Output | PNP Idle control motor |
| 33B | Idle 1 | IDLE1 | Output | PNP Idle control motor |
| 34B | Idle 3 | IDLE3 | Output | PNP Idle control motor |
| 35B | Idle 2 | IDLE2 | Output | PNP Idle control motor |
| 36B | --- | IDLE5 | Output | Available idle driver |
| 37B | --- | IDLE6 | Output | Available idle driver |
| 38B | VSV For exhaust bypass valve | LS4 | Output | PNP for EBP on stock twins |
| 39B | VSV For Exhaust gas control valve | LS5 | Output | PNP for EGC on stock twins |
| 40B | VSV For intake air control | LS3 | Output | PNP for IAC for stock twins |
| 41B | 5V Reference | +5V Sensor | Output | Dedicated |
| 42B | Sub Throttle TPS signal input | --- | --- | Not Used |
| 43B | TPS signal input | TPS | Input | Dedicated |
| 44B | Coolant Sensor Input | Coolant | Input | Dedicated |
| 45B | Air Temp Sensor | Air Temp | Input | Dedicated |
| 46B | EGR gas Temp Sensor | --- | --- | Not Used |
| 47B | AFR#1 | O2 #1 | Input | Dedicated, 0–5V signal |
| 48B | AFR#2 | O2 #2 | Input | Dedicated, 0–5V signal |
| 49B | Rear Knock Sensor | Knock 2 | Input | Dedicated, software knock filter |
| 50B | Front Knock Sensor | Knock 1 | Input | Dedicated, software knock filter |
| 51B | FAIL (98 only) | --- | --- | Not Used |
| 52B | Igniter 6 | Coil 6 | Output | Jumper: falling (5–0V) or rising (0–12V) edge |
| 53B | Igniter 5 | Coil 5 | Output | Jumper: falling (5–0V) or rising (0–12V) edge |
| 54B | Igniter 4 | Coil 4 | Output | Jumper: falling (5–0V) or rising (0–12V) edge |
| 55B | Igniter 3 | Coil 3 | Output | Jumper: falling (5–0V) or rising (0–12V) edge |
| 56B | Igniter 2 | Coil 2 | Output | Jumper: falling (5–0V) or rising (0–12V) edge |
| 57B | Igniter 1 | Coil 1 | Output | Jumper: falling (5–0V) or rising (0–12V) edge |
| 58B | Igniter return IGF1 to ECU ( 5V signal) | --- | --- | Not Used |
| 59B | --- | LS11 | Output | Available Switched Ground 1.5amp max |
| 60B | Boost Control | PW2 | Output | PNP for boost control |
| 61B | --- | --- | --- | Not Used |
| 62B | Map Sensor Input | MAP | Input | Dedicated |
| 63B | Idle2 Sw from Sub TPS to ECU & TRAC | --- | --- | Not Used |
| 64B | Idle1 Sw from Sub TPS to ECU & TRAC | --- | --- | Not Used |
| 65B | Sensor Ground | Sensor Ground | Output | Dedicated, Sensors only |
| 66B | VG signal for Airflow meter | MAF | Input | Available 0 to 5V input, 100k pull-up to 5V |
| 67B | EFIF (98 only) | EGT 4 | Input | Jumper: 0–5V, thermistor or EGT pull up |
| 68B | --- | LS9 | Output | Available Switched Ground 1.5amp max |
| 69B | Chassis Ground | Power Ground | Both | Dedicated |
| 70B | --- | Injector 7 | Output | Available, P&H Injector driver 4A/1A |
| 71B | Ox 1 Heater Ground | LS12 | Output | Available Switched Ground 1.5amp max |
| 72B | Ox 2 Heater Ground | LS2 | Output | Available Switched Ground 1.5amp max |
| 73B | Fuel Pressure up VSV | LS1 | Output | PNP fuel pressure up VSV |
| 74B | EVAP Solenoid | Injector 9 | Output | PNP for EVAP control |
| 75B | EGR Solenoid | Injector 10 | Output | PNP for EGR control |
| 76B | Neutral Starting switch | ATPNP (Gear) | Input | PNP for Neutral indicator |
| 77B | Cranking signal input (12V) | --- | --- | Not Used |
| 78B | Chassis Ground (98 only) | Power Ground | Both | Dedicated |
| 79B | Chassis Ground | Power Ground | Both | Dedicated |
| 80B | Chassis Ground | Power Ground | Both | Dedicated |
