Tuning Wiki
MoTeC M84 Gold Box engine management unit
MoTeC M84 shown as an example of the Gold Box family; it is not the M800M, whose connector configuration and details may differ. Image: MoTeC M84 datasheet; reproduced with permission.

MoTeC M800M, part 13001M, is an earlier Gold Box engine controller listed in MoTeC's obsolete-product archive. M800 marine-labelled variant. Manufacturer Gold Box archive; manufacturer model glossary.

Identification and compatibility

Read the full ECU part number, connector, firmware, options and the label before identifying the correct model. Configurations and optional engine packages vary; a similar suffix, physical plug or a common calibration does not establish a universal pinout or exact cylinder capability. The manufacturer's archived product listing provides M800M-specific documentation.

Pinout and software

Consult the MoTeC M800M product and wiring downloads and M400/M600/M800/M880 manufacturer manual. Model and marine-labelled variants must be checked against their own part numbers, connector drawings and firmware. Confirm connector orientation and the complete power, ground, sensor, injector and ignition circuits with the original documentation before wiring.

These units use a legacy ECU Manager or EMP software generation appropriate to the exact controller and firmware; M1 Tune is for M1 products. See MoTeC software archive and the MoTeC manufacturer guide.

Manufacturer connector pin list

MoTeC's M800M product page lists the standard M800 wiring drawing and the M400/M600/M800/M880 user manual for this marine model. Appendix L of that manual provides the positions below for the 66-way M800/M880 connector; positions 20, 21 and 22 are not listed in the appendix. Outputs marked * have no recirculation diode. Confirm the part number, connector orientation and electrical limits against the exact installation and manufacturer diagrams.

PinDesignationFunction and model restrictions
23,32,41VBATBattery positive
14,15,19GNDBattery negative
38V-ENG8 V engine sensor supply
165V-ENG5 V engine sensor supply
270V-ENGEngine sensor ground
28V-AUX8 V auxiliary sensor and CAN supply
345V-AUX5 V auxiliary sensor supply
110V-AUXAuxiliary sensor ground
9AUX1Auxiliary output 1
8AUX2Auxiliary output 2
43AUX3*Auxiliary output 3
51AUX4*Auxiliary output 4
59AUX5Auxiliary output 5
65AUX6Auxiliary output 6
58AUX7Auxiliary output 7
64AUX8Auxiliary output 8
1IGN1*Ignition output 1
5IGN2*Ignition output 2
4IGN3*Ignition output 3
10IGN4*Ignition output 4
17IGN5*Ignition output 5; not available on M400
25IGN6*Ignition output 6; not available on M400
33INJ1Injector output 1
50INJ2Injector output 2
63INJ3Injector output 3
66INJ4Injector output 4
24INJ5Injector output 5; not available on M400
42INJ6Injector output 6; not available on M400
57INJ7Injector output 7; not available on M400 or M600
62INJ8Injector output 8; not available on M400 or M600
26AV1Analogue voltage input 1
18AV2Analogue voltage input 2
6AV3Analogue voltage input 3
7AV4Analogue voltage input 4
12AV5Analogue voltage input 5
36AV6Analogue voltage input 6
35AV7Analogue voltage input 7
44AV8Analogue voltage input 8
28AT1Analogue temperature input 1
38AT2Analogue temperature input 2
30AT3Analogue temperature input 3
39AT4Analogue temperature input 4
29AT5Analogue temperature input 5
37AT6Analogue temperature input 6
46DIG1Digital input 1
45DIG2Digital input 2
52DIG3Digital input 3
53DIG4Digital input 4
49REFCrank reference timing input
56SYNCCam sync timing input
60LA1-PLambda 1 pump current
54LA1-SLambda 1 sense voltage
61LA2-PLambda 2 pump current; not available on M400
55LA2-SLambda 2 sense voltage; not available on M400
40TX-232RS232 transmit data
31RX-232RS232 receive data
47CAN-LOCAN bus low
48CAN-HICAN bus high
130V-COMCommunications ground

Directly applicable articles

Technical articles assigned to this context will appear here.