What the 16CU is
The Lucas 16CU is the microprocessor replacement for the 6CU on the Jaguar V12. AJ6 Engineering, whose description is the source for this page, says it is pin-compatible with the equivalent HE 6CU on cars that still have Lucas ignition, and that the external parts stay the same. Inside, it is a different machine. Functions follow a program in memory. The only analogue behaviour they describe as carried over is the injector output stage: the same two-transistor, current-limited drive, the same external resistor pack, and the same 47 V clamp. The 26CU and 36CU continue this line. They are not a 16CU with a new label.
The program
Program and fuel data sit in a 64K PROM that holds two sets, one for non-catalyst running and one for lambda feedback. A link on the board selects the set, and lambda cars need extra parts to bring the sensors to the processor and to provide the monitor outputs. Each fuel map is 16 speed sites by 8 load sites, 128 cells, with interpolation in 16 steps between cells. Further blocks hold air and coolant temperature, acceleration enrichment, overrun thresholds and the rest of the running conditions. Early 16CU programs and circuits are simpler than later ones. AJ6 Engineering says the mapping was the same, so an early unit can replace a later one of the same vehicle specification.
The trigger is still the ignition, and it is still the speed signal. A 16CU is more easily upset by an ignition fault than a 6CU. When Marelli ignition replaced Lucas ignition, the ignition ECU supplied a square-wave trigger and the 16CU input was changed to suit. A Marelli-car ECU and a Lucas-ignition ECU are not a satisfactory swap, even if the engine starts. Lambda monitoring is no longer the steady voltage of the 6CU. It is a square wave whose duty is the correction. AJ6 Engineering puts a 47 µF capacitor across a voltmeter to average it, and says mid-scale is then about 2 V rather than the 2.5 V of the 6CU. Overrun fuel cut no longer needs the vacuum threshold the 6CU used. Speed and the closed-throttle signal are enough.
Identity and the output stage
AJ6 Engineering lists the 16CU numbers, all prefixed DAC. Lucas ignition, with catalyst: 4118, 4585, 6335. Lucas ignition, without: 4119, 4478, 4586, 6336. Marelli ignition, with catalyst: 6337. Marelli ignition, without: 6338.
The output stage is less forgiving than the 6CU if the resistor pack is wrong. Disconnecting the pack, or losing both resistors for one bank, makes the current-limit switching run very fast. The spikes overload the clamp zeners. AJ6 Engineering says idle pulses may not do it, and that a few seconds at full throttle can burn the diodes and scorch the board. A diode that fails short holds that bank of injectors on. One resistor of a pair failing is not described as enough. More than about 20 V, from a boost charger or a failed alternator, is the other cause they name. The processor running warm is not, in this account, a fault: the chips came from more than one source and run at different currents. Processor failures are described as rare.
26CU
The 26CU arrived with the facelift XJ-S in 1991. The circuit and the program are more elaborate, and many inputs have extra protection. During cranking the injectors fire three times per revolution for an initial period, then return to the normal once per revolution. AJ6 Engineering attributes about a 60 percent shorter cold fire-up to that. After-start enrichment then decays with engine revolutions rather than with time. Overrun cut is no longer disabled when cold. The speeds are raised instead. Below 0 °C, cut-off is above 3000 rpm and fuel returns at 2000 rpm. Below 15 °C the speeds are 5000 rpm and 4000 rpm. The overrun air valves could be deleted. Full-load enrichment and the change to open loop come from the throttle potentiometer, and the angle at which that happens rises with speed, so the vacuum switch and the full-load microswitch are gone. There are no lambda monitor voltages. That job moves to a serial output.
Fault codes are displayed on the trip computer. AJ6 Engineering reports spurious lambda warnings, codes FF34, FF36, FF44 and FF45, and associates them with poor grounds on the lambda heater circuits. Extra earth straps between engine and body are what they say improved it. The 26CU is not interchangeable with a 6CU or a 16CU. The wiring differences they list are pins 2, 3, 4, 10, 25, 26 and 33, covering full-load enrichment, diagnostics and feedback monitoring. They also warn that the factory repair manual disagrees with the hardware in the 26CU section.
The inlet manifolds changed with this ECU. The fuel rail uses one small regulator, still 2.5 bar with the vacuum hose off, and smaller injectors seated by O-rings rather than hoses. The tracts are the same; the manifolds do not swap easily. A hot start uses a 70 °C fuel-temperature switch and a 45-second timer to raise fuel pressure through a solenoid in the regulator vacuum line, which is how the fuel cooler was deleted. Air injection runs for 45 seconds after any start. The EPROM is socketed. A modified chip has to carry a corrected checksum or the ECU's own check flags a fault.
36CU
The 36CU is the last of this line in the AJ6 Engineering account. There is no idle-mixture trim. Lambda feedback values are stored and the fuelling is set from them. The closed-throttle voltage is also learned, provided it falls between 0.22 V and 0.75 V. The setting they recommend is 0.6 V. Canister purge and air injection, in the markets that have them, are ECU outputs on pins 25 and 26, so this ECU does not interchange with the earlier types either. Those outputs are also how the ECU checks that lambda feedback still responds. A new code, FF67, is the air-injection check during idle, and it is described as over-sensitive when the heater grounds are poor. The same lambda-heater codes from the 26CU can still appear. The remedy they record is the same extra earth straps, and for some markets a revised EPROM.
Fuel pressure on this system is 3 bar, still manifold-referenced. Two in-tank pumps run in parallel. The ECU runs the primary pump through its relay. A separate module runs the second pump from a speed signal out of the Marelli ignition controller: on at 2840 rpm, off below 2000 rpm. The point of the second pump is extra delivery at higher demand without recirculating as much fuel, or putting as much heat into the tank, all the time. As with the 26CU, a calibration change is a different EPROM, and the checksum has to match.
Sources
Operation, part numbers, pin differences and the thresholds on this page are taken from AJ6 Engineering, Lucas EFI, the 16CU, 26CU and 36CU sections, updated August 2016. Accessed 2026-11-13. The analogue 6CU and 8CU are on Lucas 6CU.