Tuning Wiki
Link G4X HC92X plug-in ECU
Manufacturer product image of HC92X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X HC92X is a vehicle-specific programmable plug-in ECU for the Honda CivicLink 95 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's HC92X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The HC92X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Manufacturer connector schedules

From Link's HC92X installation manual (2025). The manual states that pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. The manufacturer identifies one CAN bus. Aux 5 and Aux 6 use high-side circuitry on the bottom board but are configured as low-side drives in PCLink; injector drives 7 and 8 are not exposed. The manufacturer lists fuel-pump relay on both A-7 and A-8 and ignition 1 on A-21 and A-22.

Main header positions

Factory pinLink ECU channelFactory function
A-1Injector 1Injection
D-1nc—
A-2Injector 4Injection
D-2nc (Constant +12V)—
A-3Injector 2Injection
D-3nc—
A-4Aux 5VTEC Solenoid (High Side)
D-4nc—
A-5Injector 3Injection
D-5nc—
A-6Aux – Inj 5Oxygen Sensor Heater
D-6nc—
A-7Aux – Inj 6Fuel Pump Relay
D-7nc—
A-8Aux – Inj 6Fuel Pump Relay
D-8nc—
A-9Aux 1ISC Solenoid
D-9nc—
A-10Ignition 4Spare
D-10nc—
A-11nc—
D-11An Volt 1TPS Signal
A-12Aux 7Engine Fan Relay
D-12nc—
A-13Aux 2CE Light
D-13An Temp 1ECT
A-14Ignition 3Spare
D-14An Volt 2Oxygen Sensor Signal
A-15Aux 3A/C Clutch Relay
D-15An Temp 2IAT
A-16nc—
D-16nc—
A-17Aux 6Intake Runner Solenoid (Integra Only)
D-17An Volt 3MAP Signal
A-18Ignition 2Spare
D-18nc—
A-19nc—
D-19+5V Out (MAP)—
A-20Aux 4Purge Solenoid
D-20+5V Out (TPS)—
A-21Ignition 1Ignition
D-21Ground (Signal)—
A-22Ignition 1Ignition
D-22Ground (Signal)—
A-23Ground—
A-24Ground—
A-25+14VECU Power
A-26Ground (Shield)—
B-1+14VECU Power
B-2Ground (Shield)—
B-3nc—
B-4nc—
B-5DI 5A/C Request
B-6nc—
B-7DI 1Clutch Switch (Some models)
B-8DI 2PS Switch
B-9DI 3Start Signal
B-10DI 4Vehicle Speed
B-11Ground (Trig 2)—
B-12Trig 2Trig 2
B-13Ground—
B-14nc—
B-15Ground (Trig 1)—
B-16Trig 1Trig 1

Expansion connector

PinLink ECU channelFactory function
1Ground (Signal)—
2+5V Out—
3Aux 8—
4DI 6—
5An Volt 4—
6An Volt 5—
7An Volt 6—
8An Temp 3—

CAN 1/RS232 Connector

PinFunctionWire colour
1Comms GNDBrown
2CAN1 LGreen
3CAN1 HWhite
4RS232-RXGrey
5RS232-TXYellow

Directly applicable articles

Technical articles assigned to this context will appear here.