
Up to eight cylinders fully sequential fuel and ignition; 12-cylinder operation is described as semi-sequential. DTAFast T8 product information.
Features and application
The T8 lists two wideband lambda controllers, two variable cam controls and configurable inputs/outputs. Select the exact connector and firmware from the manufacturer wiring document. All T-series units use the T-Series PC software; DTAFast describes configurable inputs and outputs, integrated Bosch wideband measurement, logging, firmware updates and a built-in trigger oscilloscope. Available functions and channel limits depend on the exact model and firmware. Manufacturer specification.
Identification and wiring
Identify the printed model including any “+” or “i” suffix, hardware revision, connector and firmware before allocating pins. Configurable functions may differ from defaults. Manufacturer T8 wiring diagram and connector pinout contains connector orientation, cavity functions, power, earth and sensor examples. Follow its fuse and load requirements; do not interchange pin numbering with another T-series controller.
Complete connector pin assignments
The following tables reproduce the pin positions and labels in the DTAFast T8 wiring diagram. The manufacturer's drawing shows the pin-insertion side. A dash is shown where the drawing has no function assigned; analogue, digital and PWM functions may be configured in software. Verify actual hardware revision, wiring and electrical limits against the source.
Connector 1 — pinout version 1.03
| Pin | Function in manufacturer diagram |
|---|---|
| 1 | Coil 3 |
| 2 | - |
| 3 | PWM 3 |
| 4 | PWM 2 |
| 5 | PWM 1 |
| 6 | - |
| 7 | - |
| 8 | - |
| 9 | Injector 1 |
| 10 | Coil 1 |
| 11 | Coil 5 |
| 12 | Coil 7 |
| 13 | Power Ground 1 |
| 14 | Power Ground 2 |
| 15 | Injector 6 |
| 16 | Injector 5 |
| 17 | Injector 2 |
| 18 | Coil 2 |
| 19 | Coil 8 |
| 20 | - |
| 21 | - |
| 22 | - |
| 23 | Injector 8 |
| 24 | Injector 7 |
| 25 | Injector 4 |
| 26 | Coil 4 |
| 27 | Coil 6 |
| 28 | - |
| 29 | - |
| 30 | - |
| 31 | Ignition 12v In |
| 32 | - |
| 33 | - |
| 34 | Injector 3 |
Connector 2 — pinout version 1.03
| Pin | Function in manufacturer diagram |
|---|---|
| 1 | Analogue 2 |
| 2 | Wheel 1 |
| 3 | Analogue 10 |
| 4 | Digital 1 |
| 5 | Analogue 3 |
| 6 | Analogue 4 |
| 7 | Thermistor 1 |
| 8 | Digital 2 |
| 9 | 5v Output |
| 10 | Analogue 1 |
| 11 | Digital 3 |
| 12 | Crank Sensor |
| 13 | Analogue 12 |
| 14 | Digital 4 |
| 15 | Digital 5 |
| 16 | Analogue 11 |
| 17 | Thermistor 3 |
| 18 | Analogue 5 |
| 19 | Analogue 6 |
| 20 | Wheel 2 |
| 21 | Sensor Ground |
| 22 | Cam 1 |
| 23 | - |
| 24 | 5v Output |
| 25 | Thermistor 2 |
| 26 | CAN High |
| 27 | Digital 6 |
| 28 | CAN Low |
| 29 | Cam 2 |
| 30 | - |
| 31 | Wheel 3 |
| 32 | Wheel 4 |
| 33 | Sensor Ground |
| 34 | Analogue 9 |
Connector 3 — pinout version 1.03
| Pin | Function in manufacturer diagram |
|---|---|
| 1 | Lambda 2 Pump Current |
| 2 | Lambda 2 VGND |
| 3 | Lambda 2 Heater Negative |
| 4 | PWM 9 |
| 5 | Lambda 2 Trim Resistor |
| 6 | Lambda 2 Nernst Voltage |
| 7 | Lambda 1 Pump Current |
| 8 | Lambda 1 VGND |
| 9 | Lambda 1 Heater Negative |
| 10 | PWM 8 |
| 11 | Lambda 1 Trim Resistor |
| 12 | Lambda 1 Nernst Voltage |
| 13 | - |
| 14 | - |
| 15 | - |
| 16 | - |
| 17 | Analogue 7 |
| 18 | Analogue 8 |
| 19 | - |
| 20 | - |
| 21 | - |
| 22 | PWM 4 |
| 23 | PWM 5 |
| 24 | PWM 6 |
| 25 | PWM 7 |
| 26 | Permanent 12v |
| 27 | Permanent 12v |
| 28 | PWM 10 |
| 29 | - |
| 30 | - |
| 31 | - |
| 32 | - |
| 33 | CAN 2 High |
| 34 | CAN 2 Low |
Software and related information
DTAFast provides model-specific wiring diagrams, firmware, manuals and PC software via its downloads section. Capture the existing calibration and firmware identifiers before making changes. See the DTAFast family overview for earlier S and E series models.