Tuning Wiki
MS3Pro EVO Plus HC ECU
MS3Pro EVO Plus HC. Image: manufacturer product page; permission to republish confirmed by the user.

MS3Pro EVO Plus HC is a MegaSquirt-family engine-management product. The high-current version of EVO+ is identified separately by AMP EFI; DIYAutoTune lists up to 12 high-impedance injector outputs and eight high-current spark outputs. Other supplier package pages differ in spark count, so verify the actual unit and revision. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Wiring and pinout

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

ECU connector pin assignments

These positions follow the AMP EFI EVO+ / EVO+ HC manual (firmware 1.6.1) and its HC-specific wiring diagram, both linked from the manufacturer documentation index. The HC's high-current direct-coil drivers have different electrical characteristics from the standard EVO+ logic outputs: follow the HC-specific diagram, manual and coil guidance.

White connector — 35 way

PinFunction in source
1High current out 1
2High current out 2
3Injector out J
4Injector out I
5High current out 3
6CKP+
7Knock In 2
85V+ VREF out
9TPS in
10MAT in
11CLT in
12Analog In 6
13Logic Ground
14PWM / Idle Out 1
15CKP-
16Ground
17Analog In 7
18Sensor return
19Analog in 1
20Analog in 2
21Analog in 3
22Analog In 4
23Analog In 5
24Tach out
25O2 in
26CMP+
27CMP-
28Fuel pump relay out
29PWM out 2
30PWM out 3
31Knock in 1
32Digital switched in 1
33CAN L
34CAN H
3512V+ switched power in

Gray / blue connector — 35 way

PinFunction in source
1Injector out A
2Injector out B
3Ground
4Injector out C
5Ground
6Injector out D
7Ground
8Injector out E
9Ground
10Injector out F
11Injector out G
12Injector out H
13Spark out G
14Spark out E
15Spark out C
16Spark out H
17Digital frequency in 2 (Hall)
18Ground
19Digital switched 12V in
20Digital switched in 2
21Digital frequency in 3 (unconditioned)
22Digital Frequency in 3 (VR+)
23Digital Frequency In 3 (VR-)
24Spark out F
25Spark out B
26Spark out D
27Spark out A
28Digital frequency in 1 (unconditioned)
29Digital switched in 3
30Stepper IAC out 1B
31Stepper IAC out 1A
32Stepper IAC out 2A
33Stepper IAC out 2B
34Digital Frequency in 1 (VR+)
35Digital Frequency in 1 (VR-)

Black connector — 23 way

PinFunction in source
1PWM out 5
2PWM out 4
3Digital out 2
4Digital out 1
5Digital I/O 4
6Digital I/O 2
7Analog in 8
8No connection
9No connection
10Digital switched in 5
11Digital switched in 4
12Digital I/O 5
13Digital I/O 3
14Digital I/O 1
155V+ VREF out 2
16No connection
17Sensor return
18Sensor return
19Sensor return
20Sensor return
21Sensor return
225V+ VREF out 1
23No connection

M12 serial service connector

M12 pins 1, 2, 3 and 4 map to DB9 pins 9 (5 V reference), 3 (data), 5 (ground) and 2 (data), respectively. Verify connector markings and adapter.

Directly applicable articles

Technical articles assigned to this context will appear here.