
Link G4X WRX104X is a vehicle-specific programmable plug-in ECU for the Subaru WRX 2004 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's WRX104X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The WRX104X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's WRX10X installation manual. Link describes the pinout view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle, market and board revision before use.
This is the 2004–2006 schedule from the shared WRXLink (04)/(07) guide. Do not substitute it for the other generation’s header.
Factory main header
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| A1 | DI 4 | Clutch Switch |
| C3 | Injector 4 | Injection |
| A2 | nc | — |
| C4 | Injector 3 | Injection |
| A3 | nc | — |
| C5 | Injector 2 | Injection |
| A4 | nc | — |
| C6 | Injector 1 | Injection |
| A5 | nc | — |
| C7 | DI10 | Cruise Main |
| A6 | Ground | — |
| C8 | nc (Brake NO) | — |
| A7 | nc | — |
| C9 | DI 5 | Brake Switch (NC) |
| A8 | Aux 8 | Tumble Valves Close |
| C10 | DI 6 | Cruise Cancel OR Resume |
| A9 | Linked to A10 | TGV wired in series |
| C11 | DI 7 | Cruise Set OR Cancel |
| A10 | Linked to A9 | — |
| C12 | An Temp 3 | Fuel Temperature |
| A11 | Aux 7 | Tumble Valves Open |
| C13 | An Temp 2 | IAT from MAF |
| A12 | nc | — |
| C14 | An Temp 1 | ECT |
| A13 | nc | — |
| C15 | +5V Out | — |
| A14 | Injector 5 (Aux) | Purge Solenoid |
| C16 | +5V Out | — |
| A15 | Injector 6 (Aux) | Cruise Light |
| C17 | An Volt 10 | APS (Main) |
| A16 | nc (Cruise Set Light) | — |
| C18 | An Volt 2 | TPS (Main) |
| A17 | Injector 8 (Aux) | CE Light |
| C19 | nc | — |
| A18 | +14V Out | AVCS Solenoid |
| C20 | nc | — |
| A19 | +14V Out | AVCS Solenoid |
| C21 | nc | — |
| A20 | nc | — |
| C22 | An Volt 1 | MAP |
| A21 | nc | — |
| C23 | An Volt 8 | MAF Signal |
| A22 | nc | — |
| C24 | nc | — |
| A23 | Aux 3 | Tacho |
| C25 | Knock 1 | Knock |
| A24 | nc | — |
| C26 | An Volt 4 | Left TGV Position |
| A25 | Ground | — |
| C27 | An Volt 5 | Right TGV Position |
| A26 | nc | — |
| C28 | An Volt 9 | APS (Sub) |
| A27 | nc | — |
| C29 | An Volt 3 | TPS (Sub) |
| A28 | Aux 2 | Bank 1 (RH) AVCS Solenoid |
| C30 | nc | — |
| A29 | Aux 1 | Bank 2 (LH) AVCS Solenoid |
| C31 | Ground (AFM) | — |
| A30 | nc | — |
| C32 | Ground (AFM Shield) | — |
| A31 | nc | — |
| C33 | Ground (Knock Shield) | — |
| A32 | Aux 5 | Wastegate Solenoid |
| C34 | Ground (APS) | — |
| A33 | nc | — |
| C35 | Ground (Signal) | — |
| A34 | Ground (Signal) | — |
| D1 | Ground (Signal) | — |
| B1 | Ground | — |
| D2 | Ground (Signal) | — |
| B2 | Injector 7 (Aux) | Rear Oxy Heater |
| D3 | Ground | — |
| B3 | nc | — |
| D4 | Aux 9 | EThrottle Motor + |
| B4 | Ground | — |
| D5 | Aux 10 | EThrottle Motor - |
| B5 | +14V Main Relay | ECU Power |
| D6 | +14V EThrottle | From EThrottle Relay |
| B6 | +14V Main Relay | ECU Power |
| D7 | Ground | — |
| B7 | nc | — |
| D8 | DI 8 | Start Signal |
| B8 | Trig 2 | Bank 2 (LH) Cam Position |
| D9 | DI 9 | Neutral Signal |
| B9 | DI 2 | Bank 1 (RH) Cam Position |
| D10 | An Volt 6 | Power Steer Switch |
| B10 | Trig 1 | Trig 1 (Crank) |
| D11 | nc | — |
| B11 | nc | — |
| D12 | nc | — |
| B12 | Ground | — |
| D13 | nc | — |
| B13 | nc | — |
| D14 | Ignition Switch (05- 06) | Controls Main Relay (05-06) |
| B14 | nc | — |
| D15 | Ignition Switch (04) | Controls Main Relay (04) |
| B15 | Ignition 4 | Ignition |
| D16 | DI3 (04) / Main Relay (05-06) | AC Request (04) / Ground when on (05-06) |
| B16 | Ignition 3 | Ignition |
| D17 | Main Relay (04) / DI3 (05-06) | Ground when on (04) / AC Request (05-06) |
| B17 | Ignition 2 | Ignition |
| D18 | nc | — |
| B18 | Ignition 1 | Ignition |
| D19 | nc | — |
| B19 | nc | — |
| D20 | nc | — |
| B20 | nc | — |
| D21 | nc | — |
| B21 | nc | — |
| D22 | nc | — |
| B22 | Ground (Cams) | — |
| D23 | nc | — |
| B23 | nc | — |
| D24 | nc | — |
| B24 | Ignition 5 (Aux) | AC Fan |
| D25 | An Volt 7 | Rear Oxy Signal |
| B25 | Ignition 7 (Aux) | Engine Fan |
| D26 | nc | — |
| B26 | Aux 6 (04) / DI 1 (05-06) | FP Speed (04) / Vehicle Speed (05-06) |
| D27 | nc | — |
| B27 | DI 1 (04) / Aux 6 (05-06) | Vehicle Speed (04) / FP Speed (05-06) |
| D28 | nc | — |
| B28 | nc | — |
| D29 | nc | — |
| B29 | nc | — |
| D30 | nc | — |
| B30 | nc | — |
| D31 | Ground (Shield) | — |
| B31 | Ground (Crank Shield) | — |
| B32 | nc | — |
| B33 | Ignition 6 (Aux) | AC Relay |
| B34 | nc | — |
| B35 | Ignition 8 (Aux) | E-Throttle Relay |
| C1 | nc | — |
| C2 | nc | — |
Expansion connector
| Position | Link ECU channel | Function |
|---|---|---|
| Expansion 1 | Ground (Signal) | — |
| Expansion 2 | +5V Out | — |
| Expansion 3 | nc | — |
| Expansion 4 | nc | — |
| Expansion 5 | An Volt 12 | — |
| Expansion 6 | nc | — |
| Expansion 7 | An Temp 4 | — |
| Expansion 8 | An Volt 11 | — |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |
CAN 2/OBD Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | GND | Brown |
| 2 | CAN2 L | Green |
| 3 | CAN2 H | White |
| 4 | NC | Grey |
| 5 | +14V | Yellow |