
Electromotive TECm is a model in the Total Engine Control family. The manufacturer describes TECm as a replacement motherboard for certain mid-1990s BMW Motronic ECUs; confirm the precise factory ECU and application. Manufacturer source.
Identification and software
Identify the exact model, serial, firmware and ignition-driver configuration before using a calibration or connecting a loom. WinTEC versions and hardware vary; the Electromotive manual archive separates the generations.
Wiring and pinout
Consult the model-specific manufacturer source and technical archive for the matching connector, firing order, ECU earths, injector drivers and ignition connections. Do not transfer TECgt200 or TECs200 positions to earlier TEC units. Where a complete exact-model pinout has not been verified, use the manufacturer documentation and verify the actual part number.
Availability
As of 17 November 2026, the manufacturer states it is not selling or repairing products. Electromotive notice. See the Electromotive family reference.
Factory ECU application
The manufacturer identifies TECm as a replacement motherboard for Bosch Motronic 413 and 506 units, including EWS versions, commonly used with specified BMW M50 and S50 applications. It lists six peak-and-hold injector drivers, full sequential injection and WinTEC4 configuration. Confirm original ECU number, engine and harness before ordering or fitting. TECm product specification.
Manufacturer BMW E36 connector schedule
From section 7.4 of the Electromotive TECm hardware manual. NC is reproduced as the manual’s primary-function label: pins 9 and 10 also list alternate functions, so do not interpret the label as a universal electrical disconnection. Wire colours describe the documented vehicle loom; check the original ECU connector, application and configuration.
| Pin | Primary function | Alternate function | Wire colour |
|---|---|---|---|
| 1 | Fuel pump output | — | Brown/green |
| 2 | IAC output (inverted) | PWM GPO | Black/yellow |
| 3 | Injector 5 output | — | Brown/green |
| 4 | Injector 6 output | — | Brown/violet |
| 5 | Injector 4 output | — | Brown/blue |
| 6 | Ground | — | Brown |
| 7 | Cam timing solenoid | PWM GPO | Green/blue |
| 8 | Check engine light output | — | Green |
| 9 | NC | PWM GPO | — |
| 10 | NC | Analog GPI | — |
| 11 | NC | — | — |
| 12 | NC | — | — |
| 13 | EGO + | — | Yellow |
| 14 | Sensor ground | — | Black |
| 15 | Ground | — | Black |
| 16 | Crank sensor + | — | Yellow |
| 17 | Cam sensor + | — | Yellow |
| 18 | NC | — | — |
| 19 | NC | — | — |
| 20 | NC | — | — |
| 21 | NC | — | — |
| 22 | NC | — | — |
| 23 | Coil 4 output | — | Black/blue |
| 24 | Coil 6 output | — | Black/violet |
| 25 | Coil 5 output | — | Black/green |
| 26 | +12 V switched | — | Red |
| 27 | ECU relay control | — | Brown |
| 28 | Sensor ground | — | Brown/orange |
| 29 | IAC output | PWM GPO | Black/green |
| 30 | NC | — | — |
| 31 | Injector 3 output | — | Brown/yellow |
| 32 | Injector 2 output | — | Brown/red |
| 33 | Injector 1 output | — | Brown/white |
| 34 | Ground | — | Brown |
| 35 | NC | — | — |
| 36 | Evaporative solenoid output | PWM GPO | Brown |
| 37 | NC | — | — |
| 38 | O2 sensor heater control | — | Brown/green |
| 39 | NC | — | — |
| 40 | EGO − | — | Black |
| 41 | MAF input | MAP input | Grey/yellow |
| 42 | Speed input | On/off GPI | Black/white |
| 43 | Crank sensor − | — | Black |
| 44 | Sensor ground | — | Brown |
| 45 | Shield ground | — | Bare |
| 46 | Fuel consumption gauge output | — | White/black |
| 47 | Tachometer output | — | Black |
| 48 | A/C compressor output | PWM GPO | Black/blue |
| 49 | NC | — | — |
| 50 | Coil 1 output | — | Black/white |
| 51 | Coil 2 output | — | Black/red |
| 52 | Coil 3 output | — | Black/yellow |
| 53 | NC | — | — |