AEM EMS Series 2 30-6311 is a plug-in standalone for the 1991–1997 Mitsubishi 3000GT VR4 and Dodge Stealth twin-turbo applications specified in AEM installation instructions 10-6311. The manual identifies a 3.0 L turbo V6 with six sequential injectors and three wasted-spark coils. Check the exact vehicle and harness; AEM warns non-US wiring can differ.

Configuration and wiring notes
Series 2 uses AEMTuner, not AEMPro. The manual describes 4 A peak / 1 A hold on injector drivers 1–6, a stepper idle motor, and 0–5 V falling-edge factory ignition with three wasted-spark coils. Startup calibrations are starting points and require vehicle-specific tuning. The manual states that the A/C request switch input Switch 2 is designed for +12 V, but the other switch inputs must be switched to ground; applying 12 V to switches 3, 4 or 5 may damage the ECU. Follow the manual for correct wiring and sensor calibration.
The manufacturer says the 1991–93 Active Exhaust is unsupported and its ECU connection at pin 102 must be disconnected. The source labels both 102/32 and 105/35 as PW 2; verify the specific vehicle and configuration rather than assuming they are independent.
Complete manufacturer-listed connector schedule
The table transcribes AEM's year-specific chart on pages 8–10 of the manufacturer manual. The first two columns are alternative numbers for the same physical position: select the 1991–93 or 1994–97 column, never mix the numbering conventions. The ECU-end diagrams on pages 5 and 9 show orientation. “same” means the later vehicle column uses the earlier vehicle label or note, as indicated by the source arrow; “—” reproduces a blank or dashed source entry. PnP is configured but reassignable; available means unallocated; dedicated means fixed. Pin notes on the two different years are the same unless separately stated. The table does not claim function for any positions absent from the source.
| 1991–93 pin | 1994–97 pin | 1991–93 vehicle | 1994–97 vehicle | AEM function | I/O | Manufacturer notes |
|---|---|---|---|---|---|---|
| 1 | 1 | Injector 1 | same | Injector 1 P&H | Output | Injector 1, peak/hold 4 A/1 A |
| 2 | 2 | Injector 3 | same | Injector 3 P&H | Output | Injector 3, peak/hold 4 A/1 A |
| 3 | 3 | Injector 5 | same | Injector 5 P&H | Output | Injector 5, peak/hold 4 A/1 A |
| 4 | 4 | Idle servo pin 1 | same | Idle 1 | Output | PnP stepper idle motor |
| 5 | 5 | Idle servo pin 4 | same | Idle 3 | Output | PnP stepper idle motor |
| 6 | 6 | EGR solenoid valve | same | Injector 8 | Output | Available switched ground, 1.5 A max |
| 7 | 7 | Fuel pressure solenoid | same | Switch 4 | Input | Available, switch to ground |
| 8 | 8 | MFI relay fuel pump | same | Low side 11 | Output | PnP fuel pump relay |
| 9 | 9 | EVAP purge solenoid | same | Low side 4 | Output | Available switched ground, 1.5 A max |
| 10 | 10 | Ignition power transistor 1 and 4 | same | Coil 1 | Output | PnP coil 1, rising-edge trigger |
| 11 | 11 | Ignition power transistor 3 and 6 | same | Coil 3 | Output | PnP coil 3, rising-edge trigger |
| 12 | 12 | MFI relay power in, main | same | +12 V switched | Input | Dedicated, +12 V with relay on |
| 13 | 13 | Ground | same | Ground | Input | Dedicated |
| 14 | 14 | Injector 2 | same | Injector 2 P&H | Output | Injector 2, peak/hold 4 A/1 A |
| 15 | 15 | Injector 4 | same | Injector 4 P&H | Output | Injector 4, peak/hold 4 A/1 A |
| 16 | 16 | Injector 6 | same | Injector 6 P&H | Output | Injector 6, peak/hold 4 A/1 A |
| 17 | 17 | Idle servo pin 3 | same | Idle 2 | Output | PnP stepper idle motor |
| 18 | 18 | Idle servo pin 6 | same | Idle 4 | Output | PnP stepper idle motor |
| 19 | 19 | MAF reset switch | same | Low side 8 | Output | Available switched ground, 1.5 A max |
| 20 | 20 | A/C clutch slip input | Radiator fan high | Low side 9 | Output | 1991–93 available switched ground, 1.5 A max; 1994–97 radiator fan 2 |
| 21 | 21 | Fuel pump relay low speed | Radiator fan low | Low side 2 | Output | 1991–93 available switched ground, 1.5 A max; 1994–97 radiator fan 1 |
| 22 | 22 | Magnetic clutch relay | same | Low side 6 | Output | PnP A/C compressor |
| 23 | 23 | Ignition power transistor 2 and 5 | same | Coil 2 | Output | PnP coil 2, rising-edge trigger |
| 24 | 24 | Electrical load input | same | Switch 3 | Input | Available, switch to ground |
| 25 | 25 | MFI relay power in, main | same | +12 V switched | Input | Dedicated, +12 V with relay on |
| 26 | 26 | Ground in | same | Ground | Input | Dedicated |
| 101 | 31 | Ignition OK input | Fuel pump relay low | Not used | — | — |
| 102 | 32 | Active exhaust | Wastegate solenoid | PW 2 | Output | PnP wastegate control solenoid; see active-exhaust note |
| 103 | 33 | Active exhaust switch | — | Not used | — | — |
| 104 | 34 | Timing adjust connector | Active exhaust / left-front O2 heater | Injector 12 | Output | Available injector output 1.5 A max, not peak/hold |
| 105 | 35 | Wastegate solenoid | Right-front O2 heater | PW 2 | Output | PnP wastegate control solenoid; PW 2 also listed at 102/32 |
| 106 | 36 | Check engine | same | Low side 10 | Output | PnP 7,000 rpm shift light |
| 107 | 37 | Power steering pressure switch | same | Switch 5 | Input | Available, switch to ground |
| 108 | 38 | MFI relay control | same | Main relay (coil 7) | Output | Dedicated, switched ground to relay |
| 109 | 39 | — | Boost gauge, 1996–97 | Low side 1 | Output | Available switched ground driver |
| 110 | 40 | — | Fuel pressure solenoid, 1996–97 | — | — | — |
| 111 | 41 | Boost gauge | Boost gauge, 1994–95 | EGT4 (ADCR16) | Input | Available, jumper set for 0–5 V input |
| 112 | 42 | Data link connector | Left-rear O2 heater, 1996–97 | EGT3 (ADCR15) | Input | Available, jumper set for 0–5 V input |
| 113 | 43 | Data link connector | Right-rear O2 heater, 1996–97 | High side 4 | Output | Available switched 12 V, 1.5 A max |
| 114 | 44 | ABS control | same | Switch 6 | Input | Available, switch to ground |
| 115 | 45 | Magnetic clutch | same | Switch 2 | Input | PnP A/C request switch |
| 116 | 46 | — | — | Injector 7 | Output | Available injector output 1.5 A max, not peak/hold |
| 80 | 51 | — | — | Low side 3 | Output | Available switched ground, 1.5 A max |
| 81 | 52 | — | Ignition timing adjust | Coil 3 | Output | PnP coil 3, rising-edge trigger, connected to pin 11 |
| 82 | 53 | — | — | Coil 5 | Output | Available 0–5 V rising-edge trigger |
| 83 | 54 | — | — | Injector 9 | Output | Available injector output 1.5 A max, not peak/hold |
| 84 | 55 | — | — | Low side 5 | Output | Available switched ground, 1.5 A max |
| 85 | 56 | — | Data link connector | Coil 6 | Output | Available 0–5 V rising-edge trigger |
| 86 | 57 | — | — | Idle 7 | Output | Available ground / +12 V, 1.5 A max |
| 87 | 58 | — | Ignition OK input | Not used | — | — |
| 88 | 59 | — | A/C clutch slip input | Low side 12 | Output | Available switched ground, 1.5 A max |
| 89 | 60 | — | Right-rear O2 sensor (California) | Injector 11 | Output | Available injector output 1.5 A max, not peak/hold |
| 90 | 61 | — | — | EGT2 | Input | Available, jumper set for 0–5 V input |
| 91 | 62 | — | Data link connector | Coil 4 | Output | Available 0–5 V rising-edge trigger |
| 51 | 71 | Starter signal | same | Main relay (start switch) | Input | Dedicated, activates switch 1 input |
| 52 | 72 | Intake air temperature sensor | same | AIT | Input | Dedicated, 2.2 kΩ pull-up to 5 V |
| 53 | 73 | EGR temperature sensor | Right-rear O2, 1996–97 | MAP | Input | Available 0–5 V MAP sensor input |
| 54 | 74 | — | Manifold differential pressure, 1996–97 | EGT 1 | Input | Available, jumper set for 0–5 V input |
| 55 | 75 | Right bank O2 sensor | same | O2 2 | Input | Dedicated, 0–5 V signal |
| 56 | 76 | Left bank O2 sensor | same | O2 1 | Input | Dedicated, 0–5 V signal |
| 57 | 77 | — | — | CAN1L | — | Dedicated |
| 58 | 78 | Knock sensor | same | Knock 1 | Input | Dedicated, software knock filter |
| 59 | 79 | — | Left-rear O2 sensor (California) | MAF | Input | Available 0–5 V sensor input |
| 60 | 80 | Battery backup | same | Permanent +12 V | Input | Dedicated, stores internal log |
| 61 | 81 | 5 V sensor reference power | same | +5 V sensor | Output | Dedicated, sensors only |
| 62 | 82 | Ignition switch | same | Main relay (ignition switch) | Input | Dedicated, activates switch 1 input |
| 63 | 83 | Engine coolant temperature sensor | same | Coolant | Input | Dedicated, 2.2 kΩ pull-up to 5 V |
| 64 | 84 | Throttle position sensor | same | TPS | Input | Dedicated, 100 kΩ pull-up to 5 V |
| 65 | 85 | Atmospheric pressure sensor | same | Baro volts | Input | Available 0–5 V sensor input |
| 66 | 86 | Vehicle speed sensor | same | T3 vehicle speed | Input | PnP vehicle speed sensor |
| 67 | 87 | Throttle position switch | same | CAN1H | — | Dedicated |
| 68 | 88 | Camshaft position sensor | same | Cam | Input | Dedicated camshaft sensor |
| 69 | 89 | Crankshaft position sensor | same | Crank | Input | Dedicated crankshaft sensor |
| 70 | 90 | Volume air flow sensor | same | T4 spare speed | Input | PnP frequency MAF input |
| 71 | 91 | Ground | same | Ground | Input | Dedicated |
| 72 | 92 | Sensor ground | same | Sensor ground | Output | Dedicated, sensors only |
The application summary calls for aftermarket wideband O2 sensors and says the factory O2 sensors are unsupported, while the connector schedule lists O2 channels at 55/75 and 56/76 as dedicated 0–5 V inputs. Check the actual sensor, external wideband controller and ECU calibration rather than assuming the OEM sensor can be wired directly.
Series 1 migration
AEM identifies changed pin functions relative to the 30-1311 Series 1 controller. Consult the comparison on page 11 of the manual and reconfigure converted calibrations for the 30-6311 hardware before use.