The AEM EMS Series 2 30-6030 is an application-specific plug-in engine management system. It uses the vehicle connector assignments shown in its own manufacturer installation manual; other Series 2 part numbers must not be assumed to share this schedule.

Applications and identification
The manual cover lists 2002–2004 Acura RSX (K20A2/K20A3) and 2002–2004 Honda CR-V (K24A1). Its connector chart additionally names 2001–2005 Civic D17 and Civic Si K20A3; the cover and chart differ, so verify part number and vehicle compatibility with AEM before installation.
Connector pin assignments
The following tables transcribe the connector schedule in the AEM 30-6030 installation manual, PDF pages 13, 14, 15, 16, 17. The manufacturer labels each position with its original vehicle function and its EMS function, I/O direction and notes, with vehicle wire colours. Follow the connector diagram and viewing orientation in that manual. A dash reflects the manufacturer’s entry and does not by itself establish an unused or safe connection. Where a channel is configurable, its actual use also depends on the wiring and calibration.
Connector A
| Pin | Original vehicle function | Wire colour | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|
| A1 | Primary O2 sensor heater control | Black/White (Green for D17A6) | Low Side 1 | Output | Available, switched ground, 1.5A max |
| A2 | Ignition Power 2 | Yellow/Black | Ignition Power | Input | Dedicated, +12V power for EMS |
| A3 | Ignition Power 1 | Yellow/Black | Ignition Power | Input | Dedicated, +12V power for EMS |
| A4 | Power Ground 2 | Black | Power Ground | Input | Dedicated, ground for EMS |
| A5 | Power Ground 1 | Black | Power Ground | Input | Dedicated, ground for EMS |
| A6 | Primary O2 sensor signal | Red (White for D17A1, D17A2) | O2 #1 | Input | Available, 0–5V O2 sensor #1 (connected to C13) |
| A7 | Crankshaft position sensor | Blue | Crank (T1) | Input | Dedicated, crank position sensor (T1) |
| A8 | Intake manifold runner control sensor (2002–2004 RSX K20A3 and 2002–2004 CRV K24A1 only) | Red/Yellow (K20A3/K24A1) (Yellow for D17) | MAF | Input | Available, 0–5V mass airflow sensor |
| A9 | Knock sensor | Red/Blue | Knock 1 | Input | PnP for knock sensor |
| A10 | Sensor ground 2 | Green/Yellow | Sensor Ground | Output | Dedicated, sensor ground |
| A11 | Sensor ground 1 | Green/White | Sensor Ground | Output | Dedicated, sensor ground |
| A12 | Idle air control valve | Black/Red | PW 1 | Output | PnP for idle air control valve |
| A13 | EGR valve position sensor (2001–2005 Civic D17A2/D17A6 only) | White/Black | Knock 2 | Input | Available, knock sensor 2 |
| A14 | Secondary O2 sensor heater control (2001–2005 Civic D17A1/D17A6 only) | Black/White | --- | --- | --- |
| A15 | Throttle position sensor | Red/Black | TPS | Input | PnP for throttle position sensor |
| A16 | Primary O2 sensor ground | Red/Yellow | Sensor Ground | Output | Dedicated, sensor ground |
| A17 | --- | --- | Idle 2 | Output | Available, switched +12V power, 1.5A max |
| A18 | Vehicle speed sensor | White/Green | Spare Speed (T4) | Input | PnP for vehicle speed sensor |
| A19 | Manifold absolute pressure sensor | Green/Red | MAP | Input | PnP for manifold absolute pressure sensor |
| A20 | +5V sensor power 2 | Yellow/Blue | +5V Sensor | Output | Dedicated, +5V sensor power |
| A21 | +5V sensor power 1 | Yellow/Red | +5V Sensor | Output | Dedicated, +5V sensor power |
| A22 | O2 sensor heater control | White | High Side 2 | Output | Available, switched +12V power, 1.5A max |
| A23 | Logic ground 2 | Brown/Yellow | Power Ground | Input | Dedicated, ground for EMS |
| A24 | Logic ground 1 | Brown/Yellow | Power Ground | Input | Dedicated, ground for EMS |
| A25 | Camshaft position sensor A (K-series) Secondary O2 sensor heater (2001–2005 Honda Civic D17A1/D17A6 only); | Blue/White (White/Red for D17) | Vehicle Speed (T3) | Input | Available, 0–5V vehicle speed sensor |
| A26 | Camshaft position sensor B | Green | Cam (T2) | Input | Dedicated, camshaft position sensor (T2) |
| A27 | Ignition pulse no. 4 | Brown | Coil 4 | Output | PnP for coil 4 |
| A28 | Ignition pulse no. 3 | White/Blue | Coil 3 | Output | PnP for coil 3 |
| A29 | Ignition pulse no. 2 | Blue/Red | Coil 2 | Output | PnP for coil 2 |
| A30 | Ignition pulse no. 1 | Yellow/Green | Coil 1 | Output | PnP for coil 1 |
| A31 | --- | --- | Idle 8 | Output | Available, switched +12V power, 1.5A max |
Connector B
| Pin | Original vehicle function | Wire colour | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|
| B1 | VTC oil control solenoid valve high side (except 2001–2005 Honda Civic D17A1/2/6) | Blue/White | High Side 3 | Output | PnP for VTC solenoid (Variable Valve Timing control) |
| B2 | No. 4 Injector | Yellow | Injector 4 | Output | PnP for Injector 4 |
| B3 | No. 3 Injector | Blue | Injector 3 | Output | PnP for Injector 3 |
| B4 | No. 2 Injector | Red | Injector 2 | Output | PnP for Injector 2 |
| B5 | No. 1 Injector | Brown | Injector 1 | Output | PnP for Injector 1 |
| B6 | Radiator Fan control relay | Green | Low Side 8 | Output | PnP for Radiator Fan control |
| B7 | Reverse lock solenoid valve (2002–2004 Acura RSX K20A2/3 and 2001–2005 Honda Civic SI K20A3 only) | Green | Injector 8 | Output | Available, switched ground, 1.5A max (connected to C5) |
| B8 | Engine coolant temperature sensor | Red/White | Coolant | Input | PnP for coolant temperature sensor |
| B9 | VTEC oil pressure switch (except 2001–2005 Honda Civic D17A1) | Blue/Black | Switch 4 | Input | PnP for VTEC oil pressure switch |
| B10 | Alternator L signal | White/Blue | EGT 1 | Input | Available, jumper set for 0–5V input (connected to C8) |
| B11 | --- | --- | EGT 2 | Input | Available, jumper set for 0–5V input (connected to C9) |
| B12 | --- | --- | EGT 3 | Input | Available, jumper set for 0–5V input (connected to C10) |
| B13 | Alternator F signal | White/Red | EGT 4 | Input | Available, jumper set for 0–5V input (connected to C11) |
| B14 | EGR valve control (2001–2005 Honda Civic D17A2/6 only) | Blue/Red | Injector 5 | Output | Available, switched ground, 1.5A max (connected to C2) |
| B15 | VTEC solenoid valve (except Civic D17A1) | Green/Yellow | High Side 1 | Output | PnP for VTEC solenoid valve activation |
| B16 | --- | --- | Injector 6 | Output | Available, switched ground, 1.5A max (connected to C3) |
| B17 | Intake air temperature sensor | Red/Yellow | AIT | Input | PnP for intake air temperature sensor |
| B18 | Alternator C control | White/Green | Injector 7 | Output | Available, switched ground, 1.5A max (connected to C4) |
| B19 | --- | --- | Idle 3 | Output | Available, switched ground, 1.5A max |
| B20 | --- | --- | Low Side 5 | Output | Available, switched ground, 1.5A max |
| B21 | Evaporative emission canister purge valve | Yellow/Blue | Low Side 4 | Output | Available, switched ground, 1.5A max |
| B22 | Intake manifold runner control valve (2002–2004 Acura RSX/Honda CR-V only) | Red/Blue | Low Side 3 | Output | PnP for intake manifold runner control valve |
| B23 | VTC oil control solenoid valve low side (except 2001–2005 Honda Civic D17A1/2/6) | Black/White | Injector 10 | Output | PnP for VTC solenoid (variable valve timing control, connected to C6) |
| B24 | --- | --- | Idle 4 | Output | Available, switched +12V power, 1.5A max |
Connector C
| Pin | Original vehicle function | Wire colour | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|
| C1 | --- | --- | Permanent +12V | Input | Dedicated, permanent +12V power |
| C2 | --- | --- | Injector 5 | Output | Available, switched ground, 1.5A max (connected to B14) |
| C3 | --- | --- | Injector 6 | Output | Available, switched ground, 1.5A max (connected to B16) |
| C4 | --- | --- | Injector 7 | Output | Available, switched ground, 1.5A max (connected to B18) |
| C5 | --- | --- | Injector 8 | Output | Available, switched ground, 1.5A max (connected to B7) |
| C6 | --- | --- | Injector 10 | Output | Available, switched ground, 1.5A max (connected to B23) |
| C7 | --- | --- | Injector 9 | Output | Available, switched ground, 1.5A max (connected to E21) |
| C8 | --- | --- | EGT 1 | Input | Available, jumper set for 0–5V input (connected to B10) |
| C9 | --- | --- | EGT 2 | Input | Available, jumper set for 0–5V input (connected to B11) |
| C10 | --- | --- | EGT 3 | Input | Available, jumper set for 0–5V input (connected to B12) |
| C11 | --- | --- | EGT 4 | Input | Available, jumper set for 0–5V input (connected to B13) |
| C12 | --- | --- | PW 2 | Output | Available, switched ground, 1.5A max (connected to E10) |
| C13 | --- | --- | O2 #1 | Input | Available, 0–5V O2 sensor #1 (connected to A6) |
| C14 | --- | --- | O2 #2 | Input | Available, 0–5V O2 sensor #2 (connected to E2) |
| C15 | --- | --- | Switch 1 | Input | Available, switched input (connected to E11) |
| C16 | --- | --- | Switch 2 | Input | Available, switched input (connected to E12) |
| C17 | --- | --- | Switch 3 | Input | Available, switched input |
| C18 | --- | --- | Timing Ground | Input | Available, timing ground |
| C19 | --- | --- | PW 1i | Output | Available, switched ground, inverted PW 1 signal |
| C20 | --- | --- | PW 2i | Output | Available, switched ground, inverted PW 2 signal |
| C21 | --- | --- | CAN1H | Output | Dedicated, CAN1 high side |
| C22 | --- | --- | CAN1L | Output | Dedicated, CAN1 low side |
Connector E
| Pin | Original vehicle function | Wire colour | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|
| E1 | Immobilizer fuel pump relay | Green/Yellow | Low Side 11 | Output | PnP for fuel pump relay |
| E2 | Secondary O2 sensor signal (all except D17A1/6) Third O2 sensor (2001–2005 Honda Civic D17A6 only) | White/Red (Red/Blue for K24A1) | O2 #2 | Input | Available, 0–5V O2 sensor #2 (connected to C14) |
| E3 | Logic ground 3 | Brown/Yellow | --- | --- | Not used |
| E4 | Sensor ground 3 | Pink (White/Green for K24A1) | Sensor Ground | Output | Dedicated, sensor ground |
| E5 | Sensor voltage 3 | Yellow/Blue | +5V Sensor | Output | Dedicated, sensor power |
| E6 | Secondary O2 sensor heater control (all except D17A6) Third O2 sensor heater control (2001- 2005 Honda Civic D17A6 only) | Black/White (White/Black for D17A1/6) | Low Side 12 | Output | Available, switched ground, 1.5A max |
| E7 | Main relay control | Red/Yellow | Main Relay | Output | Dedicated, ECU activates main relay with switched GND |
| E8 | O2 sensor heater control relay | Orange | Low Side 2 | Output | Available, switched ground, 1.5A max |
| E9 | Ignition switch signal 1 | Black/Yellow (Yellow/Black for Civic, CRV) | Ignition Switch | Input | Dedicated, +12V Ignition switch signal from Ign key |
| E10 | --- | --- | PW 2 | Output | Available, switched ground, 1.5A max (connected to C12) |
| E11 | --- | --- | Switch 1 | Input | Available, switched input (connected to C15) |
| E12 | --- | --- | Switch 2 | Input | Available, switched input (connected to C16) |
| E13 | --- | --- | Coil 6 | Output | Available, switched ground, 1.5A max |
| E14 | Fuel tank pressure sensor | Light Green | ADCR 13 | Input | Available, 0–5V sensor |
| E15 | Electrical load detector | Green/Red | ADCR 11 | Input | Available, 0–5V sensor |
| E16 | Power steering pressure switch signal | Light Green/Black | Switch 5 | Input | Available, switched input |
| E17 | --- | --- | Idle 5 | Input | Available, switched ground, 1.5A max |
| E18 | Air conditioner clutch relay | Red | Low Side 6 | Output | Available, switched ground, 1.5A max |
| E19 | --- | --- | Idle 6 | Output | Available, switched +12V power, 1.5A max |
| E20 | Evaporative emission bypass solenoid valve | Blue/Red (Grey / Red for K24A1) | Low Side 9 | Output | Available, switched ground, 1.5A max |
| E21 | Evaporative emissions canister vent shut valve | Light Green/Red (White/Red for K24A1) | Injector 9 | Output | Available, switched ground, 1.5A max (connected to C7) |
| E22 | Brake pedal position switch | White/Black | Switch 6 | Input | Available, switched input |
| E23 | K-line | Light blue | --- | --- | Not used |
| E24 | SEFMJ (Instrument cluster multiplex communication) | Yellow | Multiplex | Output | Dedicated, used to drive the air conditioning switch and coolant temperature gauge |
| E25 | --- | --- | Idle 7 | Output | Available, switched ground, 1.5A max |
| E26 | Engine speed pulse | Blue | Low Side 7 | Output | PnP for Tacho signal – RPM pulse to instrument cluster |
| E27 | Immobilizer code | Red/Blue (White for K24A1) | --- | --- | Not used |
| E28 | --- | --- | High Side 4 | Output | Available, switched +12V power, 1.5A max |
| E29 | Service check signal | Brown | ADCR 14 | Input | Available, 0–5V input |
| E30 | Write enable signal | Red/White | --- | --- | Not used |
| E31 | Malfunction indicator lamp (MIL) | Green/Orange (Green/White for K24A1) | Low Side 10 | Output | Available, switched ground, 1.5A max |
Documentation
AEM 30-6030 Series 2 installation instructions and wiring chart. AEM engine management support archive.