The AEM EMS Series 2 30-6052 is an application-specific plug-in engine management system. It uses the vehicle connector assignments shown in its own manufacturer installation manual; other Series 2 part numbers must not be assumed to share this schedule.

Applications and identification
The manufacturer’s manual identifies the 2000–2005 Honda S2000. Its product listing specifies manual transmission. Check the ECU part number, model year and harness before installation.
Connector pin assignments
The following tables transcribe the connector schedule in the AEM 30-6052 installation manual, PDF pages 7, 8, 9, 10. The manufacturer labels each position with its original vehicle function and its EMS function, I/O direction and notes. Follow the connector diagram and viewing orientation in that manual. A dash reflects the manufacturer’s entry and does not by itself establish an unused or safe connection. Where a channel is configurable, its actual use also depends on the wiring and calibration.
Connector A
| Pin | Original vehicle function | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| A1 | Engine Coolant Temp Gauge | Coolant dash signal | Output | Dedicated, works with AP1 and AP2 |
| A2 | Air Control Valve | Low Side Driver 1 | Output | Avail, Switched Ground, 1.5A Max |
| A3 | EVAP Bypass Solenoid Valve | Low Side Driver 3 | Output | PnP For Bypass Solenoid |
| A4 | EVAP Control Canister Vent | Low Side Driver 5 | Output | PnP For Control Canister Vent |
| A5 | --- | EGT 1 | Input | Avail, jumper set for 0–5V Input |
| A6 | EVAP Purge Control Solenoid | Low Side Driver 4 | Output | PnP For EVAP Purge Control |
| A7 | --- | Sensor Ground | Output | Avail, Sensor Ground |
| A8 | --- | Low Side Driver 12 | Output | Avail, Switched Ground, 1.5A Max |
| A9 | Vehicle Speed Sensor | T3 (Vehicle Speed) | Input | PnP for Vehicle Speed |
| A10 | Service Check Signal | Injector 12 | Output | Avail, Switched Ground, 1.5A Max |
| A11 | --- | PW3 | Output | Avail, Switched Ground, 1.5A Max |
| A12 | Immobilizer Indicator Light | Injector 9 | Output | Avail, Switched Ground, 1.5A Max |
| A13 | Immobilizer Enable Signal | Coil 7 | Output | Avail, 0/5V falling edge signal |
| A14 | --- | Injector 11 | Output | Avail, Switched Ground, 1.5A Max |
| A15 | Fuel Pump Relay | Low Side Driver 11 | Output | PnP for Fuel Pump Relay |
| A16 | --- | Low Side Driver 11 | Output | **This pin connects to A15 also** |
| A17 | A/C Clutch Relay | Low Side Driver 6 | Output | PnP For A/C Clutch |
| A18 | Malfunction Indicator Light | Low Side Driver 10 | Output | PnP For MIL |
| A19 | Engine Speed Pulse | Tach Output (LS7) | Output | PnP For Tach |
| A20 | Radiator Fan Control | Low Side Driver 8 | Output | PnP For Rad Fan Control |
| A21 | K-Line | 12VS | Output | Dedicated, filtered 12V power |
| A22 | --- | Coil 8 | Output | Avail, 0/5V falling edge signal |
| A23 | Secondary O2 Sensor | Lambda #2 | Input | PnP For Lambda #2 |
| A24 | Starter Switch Signal | Cranking | Input | PnP For Starter Switch |
| A25 | Immobilizer Code | Idle #3 | Output | Avail, Switched Ground, 1.5A Max |
| A26 | Electrical P/S Load Detect | Switch 5 | Input | Avail, Switch must connect to ground |
| A27 | A/C Switch Signal | Switch 6 | Input | PnP For A/C Request |
| A28 | Air Pump Relay | Idle #2 | Output | PnP For Air Pump |
| A29 | Fuel Tank Pressure Sensor | MAF | Input | Avail, 0–5V Input |
| A30 | Electrical Load Detector | EGT #3 | Input | Avail, jumper set for 0–5V Input |
| A31 | --- | Sensor Ground | Output | Avail, Sensor Ground |
| A32 | Brake Switch Signal | Switch 1 | Input | Avail, switch must connect to ground |
Connector B
| Pin | Original vehicle function | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| B1 | Power Source 1 | +12V Switched | Both | Dedicated |
| B2 | Power Ground 1 | Power Ground | Both | Dedicated |
| B3 | Injector 2 | Injector 2 | Output | PnP For Injector 2 |
| B4 | Injector 3 | Injector 3 | Output | PnP For Injector 3 |
| B5 | Injector 4 | Injector 4 | Output | PnP For Injector 4 |
| B6 | --- | PW 1i | Output | PnP For Idle Control Solenoid |
| B7 | --- | High Side Driver 2 | Output | Avail, Switched +12V, 1.5A Max |
| B8 | --- | Idle #5 | Output | Avail, Switched Ground, 1.5A Max |
| B9 | Power Source 2 | +12V Switched | Both | Dedicated |
| B10 | Power Ground 2 | Power Ground | Both | Dedicated |
| B11 | Injector 1 | Injector 1 | Output | PnP For Injector 1 |
| B12 | VTEC solenoid Valve | High Side Driver 1 | Output | PnP For VTEC Solenoid |
| B13 | --- | Coil 1 | Output | **This pin connects to C4 also** |
| B14 | --- | --- | --- | Not Used |
| B15 | --- | PW1 | Output | **This pin connects to B23 also** |
| B16 | --- | Injector 8 | Output | Avail, Switched Ground, 1.5A Max |
| B17 | --- | Idle #6 | Output | Avail, Switched +12V, 1.5A Max |
| B18 | --- | Idle #7 | Output | Avail, Switched Ground, 1.5A Max |
| B19 | --- | Injector 6 | Output | Avail, Switched Ground, 1.5A Max |
| B20 | Logic Ground 1 | Power Ground | Both | Dedicated |
| B21 | Voltage Back Up | Permanent +12V | Input | PnP For Perm Power |
| B22 | Logic Ground 2 | Power Ground | Both | Dedicated |
| B23 | Idle Air Control Valve | PW1 | Output | PnP For Idle Control Solenoid |
| B24 | --- | Knock 2 | Input | Available, software knock filter |
| B25 | --- | Idle #8 | Output | Avail, Switched +12V, 1.5A Max |
Connector C
| Pin | Original vehicle function | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| C1 | Primary O2 Heater Control | Low Side Driver 2 | Output | Avail, Switched Ground, 1.5A Max |
| C2 | Alternator Control | --- | --- | Not Used |
| C3 | --- | Knock 1 | Input | PnP For Knock 1 |
| C4 | Ignition Coil Pulse No. 1 | Coil 1 | Output | PnP Coil 1, 0/5V falling edge trigger |
| C5 | Alternator FR Signal | EGT #4 | Input | Avail, jumper set for 0–5V Input |
| C6 | --- | ADCR11 | Input | Available, 0–5V in |
| C7 | Sensor Ground 1 | Sensor Ground | Output | Dedicated, Sensors only |
| C8 | CKP + | Crank Sensor | Input | PnP For Crank Sensor |
| C9 | CKP - | Timing Ground | Output | PnP For Timing Ground |
| C10 | VTEC Pressure Switch Signal | Switch 4 | Input | PnP For VTEC Oil Press Sw |
| C11 | Secondary O2 Heater Control | Injector 10 | Output | Avail, Switched Ground, 1.5A Max |
| C12 | Ignition Coil Pulse No. 2 | Coil 2 | Output | PnP Coil 2, 0/5V falling edge trigger |
| C13 | Ignition Coil Pulse No. 3 | Coil 3 | Output | PnP Coil 3, 0/5V falling edge trigger |
| C14 | Ignition Coil Pulse No. 4 | Coil 4 | Output | PnP Coil 4, 0/5V falling edge trigger |
| C15 | Secondary O2 Sensor | Lambda 2 | Input | Avail, 0–5V Lambda 2 input |
| C16 | Primary O2 Sensor | Lambda 1 | Input | Avail, 0–5V Lambda 1 input |
| C17 | MAP Sensor | MAP | Input | PnP For 0–5V MAP Sensor |
| C18 | Sensor Ground 2 | Sensor Ground | Output | Dedicated, Sensors only |
| C19 | Sensor Voltage 1 | +5V Sensor | Output | Dedicated, Sensors only |
| C20 | TDC1 + | Cam | Input | Dedicated, Cam Sensor |
| C21 | TDC1 - | Timing Ground | Output | PnP, Cam Sensor Ground |
| C22 | Knock Sensor | Knock #2 | Input | Avail, Knock Sensor |
| C23 | --- | T3 (Vehicle Speed) | Input | PnP Vehicle Speed Sensor |
| C24 | Air Pump Electric Current Sensor | ADCR13 | Input | Available, 0–5V in, 100k pull up to 5V |
| C25 | Intake Air Temp Sensor | AIT | Input | PnP AIT Sensor |
| C26 | Engine Coolant Temp Sensor | Coolant | Input | PnP ECT Sensor |
| C27 | Throttle Position Sensor | TPS | Input | PnP TPS Sensor |
| C28 | Sensor Voltage 2 | +5V Sensor | Output | PnP Sensor Vcc |
| C29 | TDC2 + | T4 (Spare Speed) | Input | Avail, Spare Speed Sensor |
| C30 | TDC2 - | Timing Ground | Output | Dedicated |
| C31 | --- | Timing Ground | Output | Dedicated |
Connector D
| Pin | Original vehicle function | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| D1 | --- | Injector 5 | Output | Avail, Switched Ground, 1.5A Max |
| D2 | --- | Injector 7 | Output | Avail, Switched Ground, 1.5A Max |
| D3 | --- | Idle #1 | Output | Avail, Switched Ground, 1.5A Max |
| D4 | --- | High Side Driver 4 | Output | Avail, Switched +12V, 1.5A Max |
| D5 | --- | Idle #4 | Output | Avail, Switched +12V, 1.5A Max |
| D6 | --- | +5V Sensor | Output | Avail, 5V sensor reference power |
| D7 | --- | EGT #2 | Input | Avail, jumper set for 0–5V Input |
| D8 | --- | ADCR14 | Input | Available, 0–5V in, 100k pull up to 5V |
| D9 | --- | Sensor Ground | Output | Avail, Sensor Ground |
| D10 | --- | CAN1H | --- | Dedicated |
| D11 | --- | Switch 2 | Input | Avail, Switched GND Input |
| D12 | --- | Switch 3 | Input | Avail, Switched GND Input |
| D13 | --- | High Side Driver 3 | Output | Avail, Switched +12V, 1.5A Max |
| D14 | --- | CAN1L | --- | Dedicated |
| D15 | --- | Baro Volts | --- | Avail, 0–5V input |
| D16 | --- | PW 2 | Output | Avail, Boost Solenoid Output |
Documentation
AEM 30-6052 Series 2 installation instructions and wiring chart. AEM engine management support archive.