AEM EMS Series 2 30-6053 is an application-specific engine management system. Confirm the exact ECU and harness against its own instructions before wiring.

Application
The manufacturer identifies the 2006–2008 Honda S2000 AP2 with F22C1 engine. This system uses an adapter harness and interfaces with the original ECU. The table below describes the AEM EMS connectors and the adapter connections at that end; the stock ECU connector and adapter-intercept wiring have separate assignments in the manual.
EMS connector assignments
The following tables transcribe the AEM 30-6053 installation manual, PDF pages 17–20. Follow the connector view in the source. Dashes and blank cells reproduce the manufacturer’s entries; configurable outputs depend on wiring and calibration.
Connector A
| Pin | Adapter harness connection | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| A1 | -- | Coolant dash signal | Output | Available, provides coolant temperature gauge signal for Honda instrument cluster |
| A2 | Fuel pump | Low side 1 | Output | PnP for fuel pump activation |
| A3 | -- | Low side 3 | Output | Available, switched ground, 1.5A max |
| A4 | VTEC stock computer oil pressure switch | Low side 5 | Output | PnP for VTEC oil pressure switch |
| A5 | -- | EGT 1 | Input | Available, exhaust gas temperature sensor number 1, jumper set for 0–5V input |
| A6 | -- | Low side 4 | Output | Available, switched ground, 1.5A max |
| A7 | -- | Sensor ground | Output | Available, filtered ground for sensors |
| A8 | -- | Low side 12 | Output | Available, switched ground, 1.5A max |
| A9 | -- | Vehicle Speed (T3) | Input | Available, vehicle speed sensor (connected to C23) |
| A10 | -- | Injector 12 | Output | Available, pulse width modulated switched ground, 1.5A max |
| A11 | VTEC ground for stock computer | Filtered ground | Output | Dedicated, used to emulate the VTEC solenoid |
| A12 | -- | Injector 9 | Output | Available, pulse width modulated switched ground, 1.5A max |
| A13 | -- | Coil 7 | Output | Available, 0–5V falling edge signal (only available for use with 3-wire smart coils) |
| A14 | -- | Injector 11 | Output | Available, pulse width modulated switched ground, 1.5A max |
| A15 | -- | Low side 11 | Output | Available, switched ground, 1.5A max (connected to A16) |
| A16 | -- | Low side 11 | Output | Available, switched ground, 1.5A max (connected to A15) |
| A17 | -- | Low side 6 | Output | Available, switched ground, 1.5A max |
| A18 | -- | Low side 10 | Output | Available, switched ground, 1.5A max |
| A19 | -- | Low side 7 | Output | Available, switched ground, 1.5A max |
| A20 | Radiator fan control | Low side 8 | Output | PnP for radiator fan control (cannot be set higher than stock ECU temperature of 95°F/35°C unless tapped wire at stock ECU is disconnected) |
| A21 | -- | +12V power | Output | Available, filtered +12V power |
| A22 | -- | Coil 8 | Output | Available, 0–5V falling edge signal (only available for use with 3-wire smart coils) |
| A23 | -- | O2 #2 | Input | Available, 0–5V air-fuel ratio sensor number 2 signal |
| A24 | -- | +12V start signal | Input | Not used |
| A25 | -- | Idle 3 | Output | Available, switched ground, 1.5A max |
| A26 | -- | Switch 5 | Input | Available, switched ground input signal number 5 |
| A27 | -- | Switch 6 | Input | Available, switched ground input signal number 5 |
| A28 | -- | Idle 2 | Output | Available, switched +12V power, 1.5A max |
| A29 | -- | MAF | Input | Available, 0–5V mass air flow sensor signal |
| A30 | -- | EGT 3 | Input | Available, exhaust gas temperature sensor number 3, jumper set for 0–5V input |
| A31 | -- | Sensor ground | Output | Available, filtered ground for sensors |
| A32 | -- | Switch 1 | Input | Available, switched ground input signal number 1 |
Connector B
| Pin | Adapter harness connection | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| B1 | Ignition signal | +12V switched | Input | Dedicated, +12V power for AEM EMS |
| B2 | Power ground 1 | Power ground | Input | Dedicated, power ground for AEM EMS |
| B3 | Injector 2 | Injector 2 | Output | PnP for injector number 2 |
| B4 | Injector 3 | Injector 3 | Output | PnP for injector number 3 |
| B5 | Injector 4 | Injector 4 | Output | PnP for injector number 4 |
| B6 | -- | PW 1i | Output | Available, pulse width modulated switched ground, 1.5A max (inverted signal to PW 1) |
| B7 | -- | High side 2 | Output | Available, switched +12V power, 1.5A max |
| B8 | -- | Idle 5 | Output | Available, switched ground, 1.5A max |
| B9 | -- | +12V switched | Output | Available, switched +12V power (powered on when B1 is on) |
| B10 | Power ground 2 | Power ground | Input | Dedicated, power ground for AEM EMS |
| B11 | Injector 1 | Injector 1 | Output | PnP for injector number 1 |
| B12 | VTEC solenoid valve | High side 1 | Output | PnP for VTEC engagement signal |
| B13 | -- | Coil 1 | Output | Available, 0–5V falling edge signal number 1 (connected to C4) |
| B14 | -- | -- | -- | Not used |
| B15 | -- | PW 1 | Output | Available, pulse width modulated switched ground, 1.5A max |
| B16 | -- | Injector 8 | Output | Available, pulse width modulated switched ground, 1.5A max |
| B17 | -- | Idle 6 | Output | Available, switched +12V power, 1.5A max |
| B18 | -- | Idle 7 | Output | Available, switched ground, 1.5A max |
| B19 | -- | Injector 6 | Output | Available, pulse width modulated switched ground, 1.5A max |
| B20 | -- | Power ground | Output | Available, power ground |
| B21 | -- | +12V switched | Input | Available, switched +12V power |
| B22 | -- | Power ground | Output | Available, power ground |
| B23 | -- | PW 1 | Output | Available, pulse width modulated switched ground, 1.5A max |
| B24 | -- | Knock 2 | Input | Available, 0–5V knock sensor signal (connected to C22) |
| B25 | -- | Idle 8 | Output | Available, switched +12V power, 1.5A max |
Connector C
| Pin | Adapter harness connection | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| C1 | -- | Low side 2 | Output | Available, switched ground, 1.5A max |
| C2 | -- | -- | -- | Not used |
| C3 | Knock sensor | Knock 1 | Input | PnP for knock sensor signal (depin from stock ECU if more sensitivity is required) |
| C4 | Ignition coil 1 | Coil 1 | Output | PnP for ignition coil 1 (connected to B13) |
| C5 | -- | EGT 4 | Input | Available, exhaust gas temperature sensor number 4, jumper set for 0–5V input |
| C6 | -- | ADCR11 | Input | Available, 0–5V sensor signal |
| C7 | Sensor ground 1 | Sensor ground | Output | Dedicated, filtered ground for sensors |
| C8 | Crankshaft position sensor | Crank sensor (T1) | Input | Dedicated, crank position sensor signal |
| C9 | -- | Timing ground | Output | Available, filtered ground for speed sensors (T1–T4) |
| C10 | -- | Switch 4 | Input | Available, switched ground input signal number 4 |
| C11 | -- | Injector 10 | Output | Available, pulse width modulated switched ground, 1.5A max |
| C12 | Ignition coil 2 | Coil 2 | Output | PnP for ignition coil 2 |
| C13 | Ignition coil 3 | Coil 3 | Output | PnP for ignition coil 3 |
| C14 | Ignition coil 4 | Coil 4 | Output | PnP for ignition coil 4 |
| C15 | -- | O2 #2 | Input | Available, 0–5V air-fuel ratio sensor number 2 signal |
| C16 | -- | O2 #1 | Input | Available, 0–5V air-fuel ratio sensor number 1 signal |
| C17 | MAP signal | MAP | Input | PnP for manifold absolute pressure sensor signal |
| C18 | Sensor ground 2 | Sensor ground | Output | Dedicated, filtered ground for sensors |
| C19 | -- | +5V sensor power | Output | Available, +5V sensor power |
| C20 | Camshaft position sensor | Cam sensor (T2) | Input | Dedicated, cam position sensor signal |
| C21 | -- | Timing ground | Output | Available, filtered ground for speed sensors (T1–T4) |
| C22 | -- | Knock 2 | Input | Available, 0–5V knock sensor signal (connected to B24) |
| C23 | Vehicle speed sensor | Vehicle speed (T3) | Input | Dedicated, vehicle speed sensor signal (connected to A9) |
| C24 | -- | ADCR13 | Input | Available, 0–5V sensor signal, 100kΩ pull up resistor to 5V |
| C25 | Intake air temperature sensor | AIT | Input | PnP for intake air temperature sensor signal |
| C26 | Coolant temperature sensor | Coolant | Input | PnP for coolant temperature sensor signal |
| C27 | Throttle position sensor (located in wiring harness, not stock ECU) | TPS | Input | PnP for throttle position sensor signal |
| C28 | -- | +5V sensor power | Output | Available, +5V sensor power |
| C29 | -- | Spare speed (T4) | Input | Available, 0–5V speed sensor signal |
| C30 | -- | Timing ground | Output | Available, filtered ground for speed sensors (T1–T4) |
| C31 | -- | Timing ground | Output | Available, filtered ground for speed sensors (T1–T4) |
Connector D
| Pin | Adapter harness connection | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| D1 | -- | Injector 5 | Output | Available, pulse width modulated switched ground, 1.5A max |
| D2 | -- | Injector 7 | Output | Available, pulse width modulated switched ground, 1.5A max |
| D3 | -- | Idle 1 | Output | Available, switched ground, 1.5A max |
| D4 | -- | High side 4 | Output | Available, switched +12V power |
| D5 | -- | Idle 4 | Output | Available, switched +12V power, 1.5A max |
| D6 | Relay pin 3 | +5V filtered power | Input | Dedicated, EMS shut off |
| D7 | -- | EGT 2 | Input | Available, exhaust gas temperature sensor number 2, jumper set for 0–5V input |
| D8 | -- | ADCR14 | Input | Available, 0–5V sensor signal, 100kΩ pull up resistor to 5V |
| D9 | -- | Sensor ground | Output | Available, filtered ground for sensors |
| D10 | -- | CAN1H | -- | Dedicated, CAN1 high side |
| D11 | -- | Switch 2 | Input | Available, switched ground input signal number 2 |
| D12 | -- | Switch 3 | Input | Available, switched ground input signal number 3 |
| D13 | -- | High side 3 | Output | Available, switched +12V power, 1.5A max |
| D14 | -- | CAN1L | -- | Dedicated, CAN1 low side |
| D15 | -- | Baro volts | Input | Available, barometric pressure sensor signal |
| D16 | -- | PW 2 | Output | Available, boost solenoid pulse-width modulated switched ground |
Adapter relay connector
Separate relay, wire view, from the same manual, PDF page 21.
| Pin | Relay function | Destination | I/O | Notes |
|---|---|---|---|---|
| 1 | +12V switched input | Stock ECU E9 | Input | Dedicated |
| 2 | Ground | Stock ECU A5 | Input | Dedicated |
| 3 | Ground to +5V line | AEM EMS D6 | Output | Dedicated, used to power AEM EMS off properly |
| 4 | Ground | Stock ECU A5 | Input | Dedicated |
| 5 | -- | -- | -- | Not used |
Documentation
AEM 30-6053 Series 2 installation and wiring manual; AEM support archive.
Original Honda ECU harness and adapter cross-reference
The separate original S2000 ECU harness schedule below maps its pins to the AEM EMS through the adapter, and identifies tapped or intercepted wires. This is not the EMS connector numbering above. The source states that connector C is absent from the original harness. Source: AEM 30-6053 manual, PDF pages 13–16.
Original harness connector A
| Honda pin | Original function | AEM EMS pin location | Tapped or intercepted |
|---|---|---|---|
| A1 | Knock sensor (Knock 1 on EMS) | C3 | tapped |
| A2 | Ignition power 2 | -- | -- |
| A3 | Ignition power 1 | -- | -- |
| A4 | Power ground 2 (Power ground on EMS) | B10 | tapped |
| A5 | Power ground 1 (Power ground on EMS) | B2 Relay pins 2 & 4 | tapped |
| A6 | Camshaft position sensor (T2 on EMS) | C20 | tapped |
| A7 | Crankshaft position sensor (T1 on EMS) | C8 | tapped |
| A8 | Logic Ground 2 | -- | -- |
| A9 | Logic Ground 1 | -- | -- |
| A10 | AF sensor heater | -- | -- |
| A11 | -- | -- | -- |
| A12 | -- | -- | -- |
| A13 | Ignition Coil 4 (Coil 4 on EMS) | C14 | intercepted |
| A14 | Ignition Coil 3 (Coil 3 on EMS) | C13 | intercepted |
| A15 | Ignition Coil 2 (Coil 2 on EMS) | C12 | intercepted |
| A16 | Ignition Coil 1 (Coil 1 on EMS) | C4 | intercepted |
| A17 | -- | -- | -- |
| A18 | Vehicle Speed Sensor (T3 on EMS) | C23 | tapped |
| A19 | -- | -- | -- |
| A20 | Sensor Voltage 2 | -- | -- |
| A21 | Sensor Voltage 1 | -- | -- |
| A22 | -- | -- | -- |
| A23 | Sensor Ground 2 (Sensor ground on EMS) | C18 | tapped |
| A24 | Sensor Ground 1 (Sensor ground on EMS) | C7 | tapped |
| A25 | Accelerator Pedal Position B | -- | -- |
| A26 | Accelerator Pedal Position A | -- | -- |
| A27 | -- | -- | -- |
| A28 | AF sensor 1 signal (-) | -- | -- |
| A29 | -- | -- | -- |
| A30 | MAP signal (MAP on EMS) | C17 | tapped |
| A31 | AF sensor 1 signal (+) | -- | -- |
Original harness connector B
| Honda pin | Original function | AEM EMS pin location | Tapped or intercepted |
|---|---|---|---|
| B1 | -- (HS 4 on EMS) | D4 | intercepted |
| B2 | Injector 4 (Injector 4 on EMS) | B5 | intercepted |
| B3 | Injector 3 (Injector 3 on EMS) | B4 | intercepted |
| B4 | Injector 2 (Injector 2 on EMS) | B3 | intercepted |
| B5 | Injector 1 (Injector 1 on EMS) | B11 | intercepted |
| B6 | VTEC solenoid valve (HS 1 on EMS) | B12 | intercepted |
| B7 | -- | -- | -- |
| B8 | Coolant Temperature signal 1 (CLT on EMS) | C26 | tapped |
| B9 | -- | -- | -- |
| B10 | Alternator L signal | -- | -- |
| B11 | VTEC oil pressure switch | B10 (stock ECU side) | intercepted |
| B12 | -- | -- | -- |
| B13 | Alternator FR signal | -- | -- |
| B14 | -- | -- | -- |
| B15 | Engine mount control solenoid valve | -- | -- |
| B16 | -- | -- | -- |
| B17 | Intake Air Temperature signal (AIT on EMS) | C25 | tapped |
| B18 | Alternator Control signal (LS 3 on EMS) | -- | -- |
| B19 | Throttle Actuator signal SEFD | -- | -- |
| B20 | Throttle Actuator signal SEDF | -- | -- |
| B21 | Evap Emission Canister purge valve | -- | -- |
| B22 | -- | -- | -- |
| B23 | -- | -- | -- |
| B24 | -- | -- | -- |
Original harness connector D
| Honda pin | Original function | AEM EMS pin location | Tapped or intercepted |
|---|---|---|---|
| D1 | Cruise Control set switch | -- | -- |
| D2 | -- | -- | -- |
| D3 | -- | -- | -- |
| D4 | Cruise Control main switch | -- | -- |
| D5 | -- | -- | -- |
| D6 | -- | -- | -- |
| D7 | Cruise Control resume switch | -- | -- |
| D8 | Brake pedal position switch | -- | -- |
| D9 | Cruise Control clutch signal | -- | -- |
| D10 | -- | -- | -- |
| D11 | -- | -- | -- |
| D12 | -- | -- | -- |
| D13 | -- | -- | -- |
| D14 | -- | -- | -- |
| D15 | Throttle Actuator Relay | -- | -- |
| D16 | -- | -- | -- |
| D17 | -- | -- | -- |
Original harness connector E
| Honda pin | Original function | AEM EMS pin location | Tapped or intercepted |
|---|---|---|---|
| E1 | Engine Coolant Temperature sensor 2 | -- | -- |
| E2 | -- | -- | -- |
| E3 | Logic Ground 3 | -- | -- |
| E4 | Sensor Ground 3 | -- | -- |
| E5 | Sensor Voltage 3 | -- | -- |
| E6 | -- | -- | -- |
| E7 | Main Relay control | -- | -- |
| E8 | AF sensor heater relay | -- | -- |
| E9 | Ignition signal (ignition signal on EMS) | Relay pin 1 & B1 | tapped |
| E10 | -- | -- | -- |
| E11 | CAN High | -- | -- |
| E12 | Radiator Fan control (LS 8 on EMS) | A20 | intercepted |
| E13 | SEFMJ multiplex communication | -- | -- |
| E14 | Fuel Tank Pressure sensor | -- | -- |
| E15 | Electrical Load detector | -- | -- |
| E16 | Power Steering Load detector | -- | -- |
| E17 | Fuel Pump relay (LS 1 on EMS) | A15 | intercepted |
| E18 | A/C Compressor clutch relay | A17 | intercepted |
| E19 | Evap Canister vent shut valve | -- | -- |
| E20 | Secondary O2 sensor signal | -- | -- |
| E21 | Secondary O2 sensor heater | -- | -- |
| E22 | Brake Pedal position switch | -- | -- |
| E23 | -- | -- | -- |
| E24 | CAN Low | -- | -- |
| E25 | Engine speed pulse | -- | -- |
| E26 | Vehicle speed out | -- | -- |
| E27 | Immobilizer code | -- | -- |
| E28 | A/C switch signal | -- | -- |
| E29 | Service Check signal | -- | -- |
| E30 | Write Enable signal | -- | -- |
| E31 | -- | -- | -- |