Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

AEM Series 2 30-6052 ECU
AEM 30-6052 shown as a Series 2 family illustration; connectors and applications differ. AEM / Holley product image, reproduced with permission.

Application and identification

The AEM 10-6600 manual lists Nissan 240SX KA24DE, Sentra B13 GA16DE, Pulsar GTi-R N14 SR20DET, NX B13 GA16DE, Altima U13 KA24DE, Bluebird U13 SR20DET and Infiniti G20 P10. Verify the actual engine and harness with AEM: the document conflicts on several applications. Its cover says 1989–94 240X S13, 1991–94 Altima and G20 SR20DET, whereas the connection-table heading says 1989–94 240SX S14, 1993–94 Altima and G20 SR20DE. These source differences are not resolved here.

This Series 2 plug-in standalone ECU replaces the OEM ECU for its specified harness. AEM provides AEMTuner startup calibrations and states that Series 2 is not supported by older AEMPro software. The startup calibration must be tuned for the actual engine. The manual requires the supplied AEM replacement cam/crank trigger disc before starting: its Nissan Series 2 ECU does not support the original Nissan trigger pattern. Consult the AEM 30-6600 installation manual and trigger-disc supplement.

Connector schedule

All 64 numbered positions listed in the AEM 10-6600 connection chart, pages 8–10, are reproduced below. These are wire-view pin numbers, not sequential cavity counts: the chart lists 1–48 and 101–116, and does not assign other numbers. “PnP” means configured in the supplied calibration; “Available” means unused by that calibration or available for reassignment and may require wiring changes; “Dedicated” means fixed. Observe output limits, jumpers and sensor wiring notes in the source. Actual harness wiring varies by model year and trim; check each vehicle connection before installation.

The manual's pin 106 notes say “PnP for Fuel Pump”, although its vehicle destination is a pressure regulator solenoid and pin 104 is the fuel pump relay. The table reproduces the published descriptions; verify the intended wiring with AEM.

PinVehicle harness destinationAEM EMS functionI/OManufacturer notes
1Ignition SignalCoil 1OutputPnP for Coil 1, 0-5V falling edge trigger
2Tachometer SignalLow Side 7OutputPnP for Tachometer
3Ignition Check------Not Used
4ECCS Relay control, Ignition Relay controlMain Relay (control)OutputDedicated, EMS activates relay with switched GND
5---Coil 3OutputAvailable Coil 3, 0-5V falling edge trigger
6ECCS GroundPower GroundInputDedicated
7Data Link ConnectorCoil 2OutputAvailable Coil 2, 0-5V falling edge trigger
8EGR Sensor (Except 89-90 Non CA 240SX and SR20DET)EGT 1InputAvailable, jumper set for 0-5V Input
9Cooling Fan RelayLow Side 3 + Low Side 12OutputPnP for Cooling Fan, can be activated by LS3 or LS12 output
10Cooling Fan High Speed (A/T 2.0L only)Low Side 5OutputAvailable, Switched Ground, 1.5A max
11Air Conditioner RelayLow Side 6OutputAvailable, Switched Ground, 1.5A max
12Swirl Control Valve (89-90 240SX Only)/VTC Solenoid (1.6L only)CAN1HInputDedicated. CAN high side
13ECCS GroundPower GroundInputDedicated
14Diagnostics ClockInjector 7OutputAvailable, Switched Ground, 1.5A Max
15Data Link ConnectorEGT 2InputAvailable, jumper set for 0-5V input
16Mass Air Flow SensorMAFInputPnP for MAF Sensor
17Mass Air Flow GroundPower GroundInputDedicated
18Engine Coolant Temperature SensorCoolantInputPnP for Coolant Temp Sensor
19Oxygen SensorO2 #1InputDedicated, 0-5V input signal
20Throttle Position SensorTPSInputPnP for Throttle Position Sensor
21Sensor GroundSensor GroundOutputDedicated
22Crankshaft Reference SignalCam (T2)InputDedicated, must use AEM replacement trigger disc. Connects to pin 30
23Diagnostics check (SR20 only)Injector 5OutputAvailable, Switched Ground, 1.5A Max
24Malfunction Indicator LightLow Side 10OutputAvailable, Switched Ground, 1.5A Max
25Swirl Control Valve (91-94 240SX only)Coil 4OutputAvailable Coil 4, 0-5V falling edge trigger
26Air Temp Sensor (Late 89 and all 90 240SX)AITInputAvailable, AIT Sensor Input
27Knock Sensor (Except 89-90 240SX & 1.6L)Knock 1InputPnP for Knock Sensor
28Throttle Signal Output (A/T only)High Side 1OutputAvailable, Switched +12V, 1.5A Max
29Sensor GroundSensor GroundOutputDedicated
30Crankshaft Reference SignalCam (T2)InputDedicated, must use AEM replacement trigger disc. Connects to pin 22
31Crankshaft Position Sensor SignalCrank SignalInputDedicated, must use AEM replacement trigger disc. Connects to pin 40
32Vehicle SpeedVehicle SpeedInputPnP for Vehicle Speed Sensor
33Idle Sw (89-90 240SX)/5th Pos Sw (91-94 240SX)ADCR11InputAvailable, 0-5 Volt Input
34Start Signal+12V SwitchedInputDedicated
35Neutral Position SwitchMAPInputAvailable, Manifold Pressure
36Ignition SwitchMain Relay (input)InputDedicated, +12V activates Main Relay circuit
37Throttle Position Sensor Power+5V SensorOutputDedicated
38Power Supply for ECM+12V SwitchedInputDedicated, +12V power when ECCS Relay is on
39ECCS GroundPower GroundInputDedicated
40Crankshaft Position SignalCrank SignalInputDedicated, must use AEM replacement trigger disc. Connects to pin 31
41Air Conditioner SwitchSwitch 6InputPnP for A/C Switch
424th Position Switch (91-94 240SX only)CAN1LInputDedicated, CAN low side
43Power Steering Oil Pressure SwitchSwitch 2InputAvailable, Switched Input
44Idle Switch Positive Side (89-90 240SX); Rear window defogger (91-94 240SX)EGT 3InputAvailable, jumper set for 0-5V Input
45Air Conditioner FICD (Except 2.0L); Position Sw (89-90 240SX)Low Side 2OutputAvailable, Switched Ground, 1.5A Max
46Back-up Power SupplyPermanent +12VInputDedicated, used to store internal log
47Power Supply for ECM+12V SwitchedInputDedicated, +12V power when ECCS Relay is on
48ECCS GroundPower GroundInputDedicated
101Injector 1Injector 1OutputPnP for Injector 1 (Peak & Hold 4A/1A driver)
102Pulse Secondary Air Inj (240SX & 91-93 2.0L only)Low Side 4OutputAvailable, Switched Ground, 1.5A max
103Injector 3Injector 3OutputPnP for Injector 3 (Peak & Hold 4A/1A driver)
104Fuel Pump Relay controlLow Side 11OutputPnP for Fuel Pump
105EGR Control Solenoid ValveInjector 6OutputAvailable, Switched Ground, 1.5A max
106Pressure Regulator Control Sol (89-90 240SX only)Low Side 9OutputPnP for Fuel Pump
107ECCS GroundPower GroundInputDedicated
108ECCS GroundPower GroundInputDedicated
109Back-Up Power SupplyPermanent +12VInputDedicated, used to store internal log
110Injector 2Injector 2OutputPnP for Injector 2 (Peak & Hold 4A/1A driver)
111O2 Sensor Heater (91-94 2.0L & 94 1.6L only)PW 2OutputAvailable, Switched Ground, 1.5 max
112Injector 4Injector 4OutputPnP for Injector 4 (Peak & Hold 4A/1A driver)
113Idle Auxiliary Air Control ValvePW 1OutputPnP for Idle Air Control
114---Injector 8OutputAvailable, Switched Ground, 1.5A max
115---EGT 4InputAvailable, jumper set for 0-5V Input
116ECCS GroundPower GroundInputDedicated

Series 1 conversion differences

Compared with the corresponding 30-1600 Series 1 EMS, AEM documents these changes. After converting a V1.19 Series 1 calibration with AEMTuner, check and manually reconfigure affected functions as directed in the manual.

PinSeries 1 functionSeries 2 functionAEM note
12Low Side 8CAN1HLS8 not available
15Injector 8EGT 2Injector 8 moved to pin 114
42Switch 1CAN1LSwitch 1 not available
114EGT 2Injector 8EGT 2 moved to pin 15

Sources