AEM EMS Series 2 30-6051 is an application-specific engine management system. Confirm the exact ECU and harness against its own instructions before wiring.

Application
The AEM manual describes this system for a four-cylinder Acura/Honda vehicle with a six-cylinder engine and harness swap. Its connector chart identifies Honda Accord V6 and Odyssey and Acura TL/CL V6 donor harness variants: the two original-vehicle function columns distinguish these donors. Verify the exact donor harness and engine; the listed donor vehicles are not a claim of direct plug-in fitment in an unmodified vehicle.
EMS connector assignments
The following tables transcribe the AEM 30-6051 installation manual, PDF pages 10–13 and 15. Follow the connector view in the source. Dashes and blank cells reproduce the manufacturer’s entries; configurable outputs depend on wiring and calibration.
Connector A
| Pin | Honda Accord V6 / Odyssey donor function | Acura TL / CL V6 donor function | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|
| A1 | Engine Coolant Temp (ECT) Gauge (1999 Honda Accord V6 J30A1); MTRTW serial signal (2000–2002 Honda Accord V6 J30A1); | Secondary heated O2 sensor | --- | --- | Not used |
| A2 | Engine mount control solenoid | Low side 1 | Output | Available, switched ground, 1.5A max | |
| A3 | EVAP bypass solenoid valve | Low side 3 | Output | Available, switched ground, 1.5A max (set as reverse lockout in calibration) | |
| A4 | EVAP control canister vent shut | Low side 5 | Output | Available, switched ground, 1.5A max | |
| A5 | Cruise control signal | EGT 1 | Input | Available, jumper set for 0– 5V input | |
| A6 | EVAP purge control solenoid | Low Side 4 | Output | Available, switched ground, 1.5A max | |
| A7 | Reference voltage (2001–2002 Accord V6 J30A1 only) | Reference voltage (1999 Acura CL V6 J30A); Unterminated (2000–2003 Acura TL/CL V6 J32A1); Serial Data Line (2002–2003 Acura TL/CL V6 Type S J32A2) | Sensor +5V | Output | Dedicated, +5V sensor power output |
| A8 | Secondary O2 heater control | Low side 12 | Output | Available, switched ground, 1.5A max | |
| A9 | Vehicle speed output | Speedo freq signal | Output | PnP for speedometer signal to dashboard | |
| A10 | Service check signal | Injector 12 | Output | Available, switched ground, 1.5A max | |
| A11 | A/T range switch (2001–2002 Accord V6 J30A1 only) | --- | PW 3 | Output | Available, PWM switched ground, 1.5A max |
| A12 | Immobilizer indicator light | --- | Injector 9 | Output | Available, switched ground, 1.5A max |
| A13 | Immobilizer enable signal (1999–2000 Honda Accord V6 J30A1 only); | SVC intake manifold runner control (2002–2003 Acura TL/CL V6 Type S J32A2 only) | Coil 7 | Output | Available, 0/5V falling edge signal |
| A14 | D4 indicator light (A/T) | D5 indicator light (A/T) | Injector 11 | Output | Available, switched ground, 1.5A max |
| A15 | Fuel pump relay | Low side 11 | Output | PnP for fuel pump relay (connected to Pin A16) | |
| A16 | Immobilizer enable signal (2001–2002 Honda Accord V6 J30A1 only); | --- | Low side 11 | Output | Available, fuel pump relay (connected to Pin A15) |
| A17 | Air conditioner clutch relay | Low side 6 | Output | Available, switched ground, 1.5A max | |
| A18 | Malfunction indicator light | Low side 10 | Output | Available, switched ground, 1.5A max | |
| A19 | Engine speed pulse | Tach (Low side 7) | Output | PnP for tachometer | |
| A20 | Radiator fan control | Low side 8 | Output | PnP for radiator fan control | |
| A21 | K-line | 12 Vs | Output | Dedicated, +12V filtered power output | |
| A22 | Serial Data Line (2001–2002 Honda Accord V6 J30A1 only) | Serial Data Line (2002–2003 Acura TL/CL V6 Type S J32A2 only) | Coil 8 | Output | Available, 0/5V falling edge signal |
| A23 | Secondary O2 sensor (1999–2002 Honda Accord V6 J30A1 only) | --- | O2 #2 | Input | PnP for O2 sensor #2 (connected to C15) |
| A24 | Starter switch signal | Ignition switch | Input | Dedicated, +12V input to EMS | |
| A25 | Immobilizer code (1999–2002 Honda Accord V6 J30A1 only) | --- | Idle 3 | Output | Available, switched ground, 1.5A max |
| A26 | Power steering pressure switch | Switch 5 | Input | Available, switched input | |
| A27 | Air conditioner switch input | Switch 6 | Input | Available, switched input | |
| A28 | ILU (to multiplex control unit) | Idle 2 | Output | Available, switched +12V, 1.5A max | |
| A29 | Fuel tank pressure sensor | MAF | Input | Available, 0–5V input | |
| A30 | Electrical load detector | EGT 3 | Input | Available, jumper set for 0– 5V input | |
| A31 | TPS output signal (A/T) (2001–2002 Honda Accord V6 J30A1 only); ECT output signal (2002–2004 Honda Odyssey V6 J35A4 only) | ECT output signal (2002–2003 Acura TL/CL V6 Type S J32A2 only) | Sensor ground | Output | Available, sensor ground |
| A32 | Brake switch signal | Switch 1 | Input | Available, switched input |
Connector B
| Pin | Honda Accord V6 / Odyssey donor function | Acura TL / CL V6 donor function | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|
| B1 | Ignition Power 1 | Ignition power | Input | Dedicated, +12V input to EMS | |
| B2 | Power Ground 1 | Power ground | Input | Dedicated, ground input to EMS | |
| B3 | Cylinder 5 injector | Injector 2 | Output | PnP for cylinder 5 injector (injector 2 in calibration) | |
| B4 | Cylinder 4 injector | Injector 3 | Output | PnP for cylinder 4 injector (injector 3 in calibration) | |
| B5 | Cylinder 2 injector | Injector 4 | Output | PnP for cylinder 2 injector (injector 4 in calibration) | |
| B6 | Cylinder 6 injector | Injector 6 | Output | PnP for cylinder 6 injector (injector 6 in calibration) | |
| B7 | EGR valve | High side 2 | Output | Available, switched +12V output, 1.5A max | |
| B8 | A/T clutch pressure valve A- | Idle 5 | Output | Available, switched ground, 1.5A max | |
| B9 | Ignition Power 2 | Ignition power | Input | Dedicated, +12V input to EMS | |
| B10 | Power Ground 2 | Power ground | Input | Dedicated, ground input to EMS | |
| B11 | Injector 1 | Injector 1 | Output | PnP for cylinder 1 injector (injector 1 in calibration) | |
| B12 | VTEC solenoid valve | High side 1 | Output | PnP for VTEC solenoid valve output signal | |
| B13 | Ignition control module (1999 Honda Accord V6 J30A1 only); A/T clutch pressure valve C+ (2002–2004 Honda Odyssey V6 J35A4 only) | A/T clutch pressure valve C+ | Coil 1 | Output | Available, coil 1 0/5V falling edge signal (connected to C1) |
| B14 | 2nd clutch pressure switch (1999 Honda Accord V6 J30A1 only); Park switch (all others) | Park switch | --- | --- | Not used |
| B15 | Cylinder 3 injector | Injector 5 | Output | PnP for injector 3, switched ground (connected to D1) | |
| B16 | --- | --- | Injector 8 | Output | Available, switched ground, 1.5A max |
| B17 | A/T clutch pressure valve A+ | Idle 6 | Output | Available, switched +12V, 1.5A max | |
| B18 | A/T clutch pressure valve B- | Idle 7 | Output | Available, switched ground, 1.5A max | |
| B19 | 4th oil pressure switch (2002–2004 Honda Odyssey V6 J35A4 only) | 4th oil pressure switch | Injector 6 | Output | Available, Injector 6 switched ground, 1.5A max (connected to B6) |
| B20 | Logic ground 1 | Power ground | Input | Dedicated, ground input to EMS | |
| B21 | Voltage back-up | Permanent 12V | Input | Dedicated, +12V input to EMS | |
| B22 | Logic ground 2 | Power ground | Input | Dedicated, ground input to EMS | |
| B23 | Idle air control valve | PW 1 | Output | PnP for idle air control valve | |
| B24 | 3rd clutch pressure switch | Knock sensor 2 | Input | Available, knock sensor 2 | |
| B25 | A/T clutch pressure valve B+ | Idle 8 | Output | Available, switched +12V, 1.5A max |
Connector C
| Pin | Honda Accord V6 / Odyssey donor function | Acura TL / CL V6 donor function | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|
| C1 | Primary O2 heater control | Low side 2 | Output | Available, switched ground, 1.5A max | |
| C2 | Alternator C | --- | --- | Not used | |
| C3 | Cylinder 3 coil | Coil 5 | Output | PnP for cylinder 3 coil (uses coil 5 in calibration), 0/5V falling edge signal | |
| C4 | Cylinder 1 coil | Coil 1 | Output | PnP for cylinder 1 coil, 0/5V falling edge signal | |
| C5 | Alternator F | EGT 4 | Input | Available, jumper set for 0–5V input | |
| C6 | EGR valve lift sensor | ADCR11 | Input | Available, 0–5V input | |
| C7 | Sensor ground 1 | Sensor ground | Output | Dedicated, sensor ground output | |
| C8 | CKP + | Crank sensor signal | Input | Dedicated, crank position sensor input | |
| C9 | CKP - | Crank sensor ground | Output | Dedicated, crank position sensor ground output | |
| C10 | VTEC pressure switch signal | Switch 4 | Input | PnP for VTEC oil pressure switch | |
| C11 | --- | --- | Injector 10 | Output | Available, switched ground, 1.5A max |
| C12 | Cylinder 5 coil | Coil 2 | Output | PnP for cylinder 5 coil (uses coil 2 in calibration), 0/5V falling edge signal | |
| C13 | Cylinder 4 coil | Coil 3 | Output | PnP for cylinder 4 coil (uses coil 3 in calibration), 0/5V falling edge signal | |
| C14 | Cylinder 2 coil | Coil 4 | Output | PnP for cylinder 2 coil (uses coil 4 in calibration, 0/5V falling edge signal | |
| C15 | --- | --- | O2 #2 | Input | Available, 0–5V O2 sensor #2 input (connected to A23) |
| C16 | Primary O2 sensor | O2 #1 | Input | PnP, 0–5V O2 sensor #1 input | |
| C17 | MAP sensor | MAP | Input | PnP, 0–5V MAP sensor input | |
| C18 | Sensor ground 2 | Sensor ground | Output | Dedicated, sensor ground output | |
| C19 | Sensor voltage 1 | Sensor +5V | Output | Dedicated, sensor +5V output | |
| C20 | TDC1+ | Cam sensor signal | Input | Dedicated, cam sensor input (T2) | |
| C21 | TDC1- | Cam sensor ground | Output | Dedicated, cam sensor ground output | |
| C22 | Knock Sensor (2002–2004 Honda Odyssey V6 J35A4 only) | Knock sensor | Knock sensor 1 | Input | PnP for knock sensor 1 |
| C23 | Cylinder 6 coil | Coil 6 | Output | PnP for cylinder 6 coil (uses coil 6 in calibration), 0/5V falling edge signal | |
| C24 | ATF temperature sensor (2002– 2004 Honda Odyssey V6 J35A4 only) | ATF temperature sensor | ADCR13 | Input | Available, 0–5V input, 100Kohm pull up resistor to +5V |
| C25 | Intake air temperature sensor | AIT | Input | PnP for intake air temperature sensor | |
| C26 | Engine coolant temperature sensor | Coolant | Input | PnP for engine coolant temperature sensor | |
| C27 | Throttle position sensor | TPS | Input | PnP for throttle position sensor | |
| C28 | Sensor voltage 2 | Sensor +5V | Output | Dedicated, sensor +5V output | |
| C29 | TDC2+ | Spare speed (T4) | Input | Available, spare speed sensor | |
| C30 | TDC2- | Timing ground | Output | Available, spare speed sensor ground | |
| C31 | --- | --- | Timing ground | Output | Available, spare speed sensor ground |
Connector D
| Pin | Honda Accord V6 / Odyssey donor function | Acura TL / CL V6 donor function | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|
| D1 | Lock-up control solenoid valve | Injector 5 | Output | Available, switched ground, 1.5A max (connected to B15) | |
| D2 | Shift control solenoid valve B | Injector 7 | Output | Available, switched ground, 1.5A max | |
| D3 | Shift control solenoid valve C | Idle 1 | Output | Available, switched ground, 1.5A max | |
| D4 | --- | A/T gear position switch signal | High side 4 | Output | Available, switched input |
| D5 | Battery flyback solenoid | Idle 4 | Output | Available, switched +12V, 1.5A max | |
| D6 | A/T reverse switch | Sensor +5V | Output | Available, sensor +5V output | |
| D7 | Shift control solenoid valve A | EGT 2 | Input | Available, jumper set for 0–5V input | |
| D8 | A/T D3 sw | A/T D4 sw | ADCR14 | Input | Available, 0–5V input, 100Kohm pull up resistor to +5V |
| D9 | A/T D4 sw (1999–2002 Honda Accord V6 J30A1); A/T D5 sw (2002–2004 Honda Odyssey V6 J35A4) | A/T D5 sw | Sensor ground | Output | Available, sensor ground output |
| D10 | Countershaft speed sensor + | CAN1H | --- | Dedicated, CAN high side | |
| D11 | Mainshaft speed sensor + | Vehicle Speed (T3) | Input | PnP for vehicle speed sensor input | |
| D12 | Mainshaft speed sensor - | Switch 3 | Input | Available, switched +12V input, 1.5A max | |
| D13 | Park switch (1999 Honda Accord V6 J30A1); 2nd clutch pressure switch (2000 Honda Accord V6 J30A1); | 3rd oil pressure switch | High side 3 | Output | Available, switched +12V output, 1.5A max |
| D14 | A/T 2 sw | A/T 3 sw | CAN1L | --- | Dedicated, CAN low side |
| D15 | A/T 1 sw | A/T 2 sw | Baro Volts | Input | Available, 0–5V input |
| D16 | Countershaft speed sensor - | PW 2 | Output | Available, boost solenoid output |
Documentation
AEM 30-6051 Series 2 installation and wiring manual; AEM support archive.