
Application and identification
AEM's 10-6611 instructions list the following applications; verify engine, market, transmission, ECU connectors and harness revision:
- 1996–1998 Nissan 240SX S14 KA24DE (OBD II).
- 1997–1999 Nissan Sentra B14 SR20DE/GA16DE and 1997–1998 200SX B14 SR20DE/GA16DE, except 1997 2.0-litre.
- 1996–1999 Nissan Altima U13 KA24DE, except 1996 non-California models.
- 1999 Infiniti G20 SR20DE, described as P10 in the manual: verify this chassis designation and actual vehicle harness with AEM.
The manufacturer says the Series 2 30-6611 supersedes 30-1611 and its U variant. This does not mean that the calibration or pin assignments can be transferred without checking. Use AEMTuner; AEM says its older AEMPro software does not support Series 2. AEM's supplied Nissan replacement cam/crank trigger disc is required before engine start; consult its 30-661X trigger-disc supplement and model-specific manual.
Manufacturer connector schedule
The table transcribes all 88 positions listed in the AEM 10-6611 connection chart, pages 9–12: 1–70 and 101–118. Numbers not listed in that chart are not assumed unused. These are wire-view references; consult the source diagram for orientation. “PnP” is configured in the supplied calibration but can be reassigned; “Available” is not allocated by default; “Dedicated” has a fixed function. Factory harness circuits can differ by model year, trim and modifications. Check each actual circuit, output limit and installed jumper.
The chart describes several vehicle circuits as “95–96 240SX” even though the manual's fitment list starts at 1996; confirm the car's actual wiring. It calls both pin 8 (fuel-pump relay) and pin 115 (front oxygen heater) Low Side 11; verify whether these are connected or whether one is a document error before using either. The manufacturer notes for pins 58 and 64 call them coil outputs but describe switched-ground limits; clarify the drive type with AEM before connecting an ignition circuit.
| Pin | Vehicle harness circuit | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| 1 | Ignition Signal | Coil 1 | Output | PnP for coil 1, 0-5V falling edge trigger |
| 2 | Ignition Check | EGT 3 | Input | Available, jumper set for 0-5V input |
| 3 | Tachometer | Tachometer (LS7) | Output | PnP for tachometer |
| 4 | ECCS Self-Shutoff Relay | Main Relay | Output | Dedicated, EMS activates relay with switched GND |
| 5 | EVAP Purge Control Valve | Idle 4 | Output | Available, switched +12V, 1.5A max |
| 6 | EVAP Purge Control Valve (Except Altima) | Idle 3 | Output | Available, switched ground, 1.5A max |
| 7 | M/T 5th position switch (240SX Only) | ADCR14 | Input | Available, 0-5V sensor |
| 8 | Fuel Pump Relay | Low Side 11 | Output | PnP for fuel pump |
| 9 | A/C Triple Pressure Switch (240SX & Altima Only) | ADCR11 | Input | Available, 0-5V Input |
| 10 | ECCS Ground | Power Ground | Input | Dedicated, ground for EMS |
| 11 | --- | High Side 1 | Output | Available, switched +12V, 1.5A Max |
| 12 | A/C Triple-Pressure Switch (95-96 240SX Only) | CAN1L | Output | Dedicated, CAN1 low side |
| 13 | Cooling Fan High Relay (240SX & Altima Only) | Low Side 5 | Output | PnP for cooling fan |
| 14 | Cooling Fan Low Relay | Low Side 3 | Output | PnP for cooling fan |
| 15 | Air Conditioner Relay | Low Side 6 | Output | PnP for air conditioner compressor relay activation |
| 16 | EVAP Purge Control Valve (Except Altima) | Idle 2 | Output | Available, switched +12V, 1.5A max |
| 17 | EVAP Purge Control Valve (Except Altima) | Idle 1 | Output | Available, switched ground, 1.5A max |
| 18 | Malfunction Indicator Light | Low Side 10 | Output | Available, switched ground, 1.5A max |
| 19 | ECCS Ground | Power Ground | Input | Dedicated, ground for EMS |
| 20 | Start Signal | Start | Input | Dedicated, start signal |
| 21 | Air Conditioner Switch | Switch 6 | Input | PnP for air conditioning switch |
| 22 | M/T Neutral Position Switch | Switch 4 | Input | Available, switched input |
| 23 | Throttle Position Sensor | TPS | Input | Dedicated, throttle position sensor |
| 24 | Blower Fan Switch (97-99 1.6L Only) | ADCR13 | Input | Available, 0-5V input |
| 25 | Power Steering Oil Pressure Switch | Switch 2 | Input | Available, switched input |
| 26 | Vehicle Speed Sensor | Vehicle Speed (T3) | Input | PnP for vehicle speed |
| 27 | Throttle Closed Switch | Switch 5 | Input | Available, switched input |
| 28 | Intake Air Temperature Sensor | IAT | Input | PnP for intake air temperature |
| 29 | A/T Signal 2 | Injector 5 | Output | Available, switched ground, 1.5A max |
| 30 | A/T Signal 3 | Injector 6 | Output | Available, switched ground, 1.5A max |
| 31 | --- | Injector 7 | Output | Available, switched ground, 1.5A max |
| 32 | --- | Injector 8 | Output | Available, switched ground, 1.5A max |
| 33 | A/T Signal 4 (Throttle Position Signal) | Idle 6 | Output | Available, switched ground, 1.5A max |
| 34 | --- | PW 2 | Output | Available, pulse width out |
| 35 | --- | Switch 1 | Input | Available, switched input |
| 36 | --- | Coil 4 | Output | Available, coil 4, 0-5V falling edge trigger |
| 37 | --- | Low Side 2 | Output | Available, switched ground, 1.5A max (connected to Pin 57) |
| 38 | Ignition Switch | Main Relay | Input | Dedicated, +12V activates main relay circuit |
| 39 | ECCS Ground | Power Ground | Input | Dedicated, ground for EMS |
| 40 | Camshaft Position Reference Signal | Cam (T2) Signal | Input | Dedicated, camshaft position sensor, connected to pin 44 |
| 41 | Camshaft Position Signal | Crank Signal | Input | Dedicated, crankshaft position sensor |
| 42 | IACV-AAC Close Valve (97-99 1.6L) | --- | --- | Not Used |
| 43 | ECCS Ground | Power Ground | Input | Dedicated, ground for EMS |
| 44 | Camshaft Position Reference Signal | Cam (T2) Signal | Input | Dedicated, camshaft position sensor, connected to pin 40 |
| 45 | Camshaft Position Signal (97 Sentra & 200SX Only) | --- | --- | Not Used |
| 46 | Front Heated Oxygen Sensor | O2 #1 | Input | Dedicated, 0-5V input signal |
| 47 | Mass Air Flow Sensor | MAF | Input | PnP for MAF sensor |
| 48 | Mass Air Flow Ground | Power Ground | Input | Dedicated, ground for EMS |
| 49 | Sensor Power Supply | +5V Sensor | Output | Dedicated, +5V sensor power |
| 50 | Sensor Ground | Sensor Ground | Output | Dedicated, sensor ground |
| 51 | Engine Coolant Temperature Sensor | Coolant | Input | Dedicated, coolant temperature sensor |
| 52 | Rear Heated Oxygen Sensor | O2 #2 | Input | Available, O2 sensor input |
| 53 | Crankshaft Position OBD Sensor | --- | --- | Not Used |
| 54 | Knock Sensor | Knock 1 | Input | PnP for knock sensor |
| 55 | Rear Defogger Switch (Except 2.0L) | --- | --- | Not Used |
| 56 | Power Supply for ECM | +12V Switched | Input | Dedicated, +12V power for EMS |
| 57 | Ambient Temp Switch (95-96 240SX Only) | Low Side 2 | Output | Available, switched ground, 1.5A max (connected to pin 37) |
| 58 | Data Link Connector for GST | Coil 2 | Output | Available, switched ground, 1.5A max |
| 59 | Blower Fan Switch (99 Altima Only) | --- | --- | Not Used |
| 60 | Headlamp Switch (except 2.0L & 95-96 240SX) | Switch 3 | Input | Available, switched input |
| 61 | Power Supply for ECM | +12V Switched | Input | Dedicated |
| 62 | EGR Temperature Sensor | EGT 1 | Input | Available, jumper set to 0-5V input |
| 63 | Tank Fuel Temperature Sensor | --- | --- | Not Used |
| 64 | Data Link Connector for CONSULT | Coil 3 | Output | Available, switched ground 1.5A max |
| 65 | Data Link Connector for CONSULT | EGT 2 | Input | Available, jumper set to 0-5V Input |
| 66 | Absolute Pressure | MAP | Input | Available, manifold absolute pressure sensor |
| 67 | EVAP Pressure | EGT 4 | Input | Available, jumper set to 0-5V input |
| 68 | Data Link Connector for CONSULT | Knock 2 | Input | Available, 0-5V input |
| 69 | MAP/Baro Switch | CAN1H | Output | Dedicated, CAN1 high side |
| 70 | Back-Up Power Supply | Permanent +12V | Input | Dedicated, +12V power for EMS |
| 101 | IACV-AAC Open Valve | PW1 | Output | PnP for idle air control |
| 102 | Injector 1 | Injector 1 | Output | PnP for injector 1 |
| 103 | EGRC-Solenoid Valve | Idle 5 | Output | Available, switched +12V, 1.5A max |
| 104 | Injector 3 | Injector 3 | Output | PnP for injector 3 |
| 105 | EVAP Canister Purge Control Solenoid Valve | Low Side 12 | Output | Available, switched ground, 1.5A max |
| 106 | ECCS Ground | Power Ground | Input | Dedicated, ground for EMS |
| 107 | Injector 2 | Injector 2 | Output | PnP for injector 2 |
| 108 | EVAP Vent / Rear O2 Sensor Heater (95-96 240SX Only) | Low Side 4 | Output | Available, switched ground, 1.5A max |
| 109 | Injector 4 | Injector 4 | Output | PnP for injector 4 |
| 110 | Rear O2 Heater (Except 95-96 240SX) | Low Side 9 | Output | Available, switched ground, 1.5A max |
| 111 | Rear O2 Sensor Heater Ground (95-96 240SX Only) | Power Ground | Input | Dedicated, ground for EMS |
| 112 | ECCS Ground | Power Ground | Input | Dedicated, ground for EMS |
| 113 | Current Return | Permanent +12V | Input | Dedicated, +12V power for EMS |
| 114 | REC Relay (240SX) / Intake VTC Solenoid (1.6L) | Low Side 8 | Output | Available, switched ground, 1.5A max |
| 115 | Front O2 Sensor Heater | Low Side 11 | Output | Available, switched ground, 1.5A max |
| 116 | EVAP Vent (95-96 240SX Only) | Injector 9 | Output | Available, switched ground, 1.5A max |
| 117 | Vacuum Cut Bypass Valve (240SX Only) | Injector 10 | Output | Available, switched ground, 1.5A max |
| 118 | ECCS Ground | Power Ground | Input | Dedicated, ground for EMS |
Series 1 migration
AEM identifies these changes from the 30-1611 Series 1 EMS. Following conversion of a V1.19 Series 1 calibration in AEMTuner, the manual says affected functions must be checked and manually reconfigured as directed.
| Pin | Vehicle circuit | Series 1 function | Series 2 function |
|---|---|---|---|
| 12 | A/C triple-pressure switch | --- | CAN1L |
| 69 | --- | Coil 5 | CAN1H |