The AEM EMS Series 2 30-6310 is a plug-in standalone ECU. AEM instructions 10-6310 list 1995–1999 Mitsubishi Eclipse GS-T/GS-X and Eagle Talon TSi, and 2003–2005 Mitsubishi Lancer Evolution VIII. Check the specific engine and harness: the same position can serve different vehicle functions across applications, and AEM warns non-US wiring can differ.

Operating notes
The manufacturer describes 4 A peak / 1 A hold injector drivers 1–6, stepper idle, and AEMTuner software; AEMPro does not support Series 2. The factory MAF/IAT can be retained or the load strategy can be configured for a MAP sensor. Startup calibrations need tuning for the specific engine. The fuel pump and A/C relay assignments exchange between the DSM and EVO VIII applications: the manual identifies low side 11 at pin 8 as the DSM fuel pump and EVO A/C relay, and low side 6 at pin 22 as the DSM A/C relay and EVO fuel pump.
Switch input 2 is intended for the +12 V factory A/C request; the manual says other switch inputs are switched to ground and applying 12 V to switches 3, 4 or 5 can damage the EMS. Consult the source before making changes.
Manufacturer-listed connector schedule
Transcribed from the AEM connection chart on pages 10–13 of the 30-6310 manual. Consult its connector diagram for orientation. “same” translates the source's left arrow: that application uses the preceding vehicle function or note. A dash reproduces a blank or dashed source entry and does not establish that the position is safe to use. PnP denotes configured but reassignable, available denotes an unallocated function, and dedicated denotes a fixed assignment. Positions not present in the source are not inferred.
The manual itself lists an injector-output note on pin 61, whose I/O column calls EGT2 an input, and an input note on pin 62, whose column calls coil 4 an output. These conflicts are preserved and must be verified. Pin 23's source vehicle label is “2&4”; it is reproduced without correction. Confirm all wiring against the exact ECU, harness and calibration.
| Pin | 1995–99 Eclipse/Talon | 2003–05 EVO VIII | AEM function | I/O | Eclipse/Talon notes | EVO VIII notes |
|---|---|---|---|---|---|---|
| 1 | Injector 1 | same | Injector 1 P&H | Output | Injector 1, peak/hold 4 A/1 A | same |
| 2 | Injector 3 | same | Injector 3 P&H | Output | Injector 3, peak/hold 4 A/1 A | same |
| 3 | Fuel pressure solenoid | same | Injector 5 P&H | Output | Injector 5, peak/hold 4 A/1 A | same |
| 4 | Idle speed control servo pin 1 | Idle speed control servo A1 | Idle 1 | Output | PnP stepper idle motor | same |
| 5 | Idle speed control servo pin 4 | Idle speed control servo B1 | Idle 3 | Output | PnP stepper idle motor | same |
| 6 | EGR solenoid valve | same | Injector 8 | Output | Available injector output, 1.5 A max, not peak/hold | same |
| 7 | — | — | Not used | — | — | — |
| 8 | MFI relay fuel pump | Magnetic clutch relay | Low side 11 | Output | PnP fuel pump relay | PnP A/C compressor relay |
| 9 | EVAP purge solenoid | same | Low side 4 | Output | Available switched ground, 1.5 A max | same |
| 10 | Ignition power transistor 1 and 4 | same | Coil 1 | Output | PnP coil 1 rising-edge trigger | same |
| 11 | Wastegate solenoid valve | same | PW 2 | Output | PnP wastegate control solenoid | same |
| 12 | MFI relay power in, main | same | +12 V switched | Input | Dedicated, +12 V when relay is on | same |
| 13 | Ground | same | Ground | Input | Dedicated | same |
| 14 | Injector 2 | same | Injector 2 P&H | Output | Injector 2, peak/hold 4 A/1 A | same |
| 15 | Injector 4 | same | Injector 4 P&H | Output | Injector 4, peak/hold 4 A/1 A | same |
| 16 | Boost gauge | — | Injector 6 P&H | Output | Available injector 6, peak/hold 4 A/1 A | same |
| 17 | Idle speed control servo pin 3 | Idle speed control servo A2 | Idle 2 | Output | PnP stepper idle motor | same |
| 18 | Idle speed control servo pin 6 | Idle speed control servo B2 | Idle 4 | Output | PnP stepper idle motor | same |
| 19 | MAF reset switch | same | Low side 8 | Output | Available switched ground, 1.5 A max | same |
| 20 | Radiator/condenser fan relay HI, LO2 | — | Low side 9 | Output | PnP fan control | Available switched ground, 1.5 A max |
| 21 | Radiator fan relay LO1 | Cooling fan control signal | Low side 2 | Output | Available switched ground, 1.5 A max | PnP user 1 PW output, coolant |
| 22 | Magnetic clutch relay | MFI relay fuel pump | Low side 6 | Output | PnP A/C compressor | PnP fuel pump relay |
| 23 | Ignition power transistor 2 and 4 | same | Coil 2 | Output | PnP coil 2 rising-edge trigger | same |
| 24 | — | same | Switch 3 | Input | Available, switch to ground | same |
| 25 | MFI relay switched power | same | +12 V switched | Input | Dedicated, +12 V when relay is on | same |
| 26 | Ground | same | Ground | Input | Dedicated | same |
| 31 | — | same | Idle 8 | Output | Available ground / +12 V, 1.5 A max | same |
| 32 | — | Condenser fan relay high | Idle 5 | Output | Available ground / +12 V, 1.5 A max | PnP fan control |
| 33 | Voltage regulator G | same | Not used | — | — | — |
| 34 | — | Condenser fan relay low | Injector 12 | Output | Available injector output, 1.5 A max, not peak/hold | PnP fan control |
| 35 | — | Water spray LED | Injector 10 | Output | Available injector output, 1.5 A max, not peak/hold | PnP water spray |
| 36 | Check engine light | Service engine soon lamp | Low side 10 | Output | PnP 7,000 rpm shift light | same |
| 37 | Power steering pressure switch | same | Switch 5 | Input | Available, switch to ground | same |
| 38 | MFI relay | same | Main relay coil 7 | Output | Dedicated, switched ground activates relay | same |
| 39 | — | Fuel pump low-speed relay | Low side 1 | Output | Available switched ground driver | PnP fuel pump low-speed relay |
| 40 | — | MAF ground | Sensor ground | Output | Dedicated, sensors only | same |
| 41 | Voltage regulator FR | same | EGT4 (ADCR16) | Input | Available, jumper set for 0–5 V input | same |
| 42 | — | same | EGT3 (ADCR15) | Input | Available, jumper set for 0–5 V input | same |
| 43 | — | Clutch pedal switch | Switch 4 | Input | Available, switch to ground | PnP clutch switch |
| 44 | — | Water spray auto switch | Switch 6 | Input | Available, switch to ground | PnP water spray |
| 45 | Automatic compressor ECM | same | Switch 2 | Input | PnP A/C request switch | same |
| 46 | — | same | Injector 7 | Output | Available injector output, 1.5 A max, not peak/hold | same |
| 51 | — | Immobilizer system | Low side 3 | Output | Available switched ground driver | same |
| 52 | Ignition timing adjust connector | — | Coil 3 | Output | Available switched ground, 1.5 A max | Available switched ground, 1.5 A max |
| 53 | — | same | Coil 5 | Output | Available switched ground, 1.5 A max | same |
| 54 | Rear O2 heater | same | Injector 9 | Output | Available switched ground, 1.5 A max | same |
| 55 | EVAP vent solenoid valve, 1999 only | EVAP vent solenoid valve | Low side 5 | Output | Available injector output, 1.5 A max, not peak/hold | same |
| 56 | Data link connector | — | Coil 6 | Output | Available switched ground, 1.5 A max | same |
| 57 | — | Water spray relay | Idle 7 | Output | Available ground / +12 V, 1.5 A max | PnP water spray |
| 58 | Tachometer | same | Low side 7 | Output | PnP tachometer | PnP tachometer |
| 59 | — | same | Low side 12 | Output | Available switched ground driver | same |
| 60 | Front O2 heater | same | Injector 11 | Output | Available switched ground, 1.5 A max | same |
| 61 | Fuel tank differential pressure sensor, 1999 only | Fuel tank differential pressure sensor | EGT2 | Input | Available injector output, 1.5 A max, not peak/hold (as printed; conflicts with input label) | same |
| 62 | Data link connector | same | Coil 4 | Output | Available, jumper set for 0–5 V input (as printed; conflicts with output label) | same |
| 71 | Starter signal | same | Main relay start switch | Input | Dedicated, activates switch 1 input | same |
| 72 | Intake air temperature sensor | same | AIT | Input | Dedicated, 2.2 kΩ pull-up to 5 V | same |
| 73 | Manifold differential pressure sensor | same | MAP | Input | Available 0–5 V MAP sensor input | same |
| 74 | — | Fuel level input | EGT 1 | Input | Available, jumper set for 0–5 V input | same |
| 75 | Rear O2 sensor | same | O2 2 | Input | Dedicated, 0–5 V signal | same |
| 76 | Front O2 sensor | same | O2 1 | Input | Dedicated, 0–5 V signal | same |
| 77 | — | Fuel temperature | CAN1L | — | Dedicated | same |
| 78 | Knock sensor | same | Knock 1 | Input | Dedicated, software knock filter | same |
| 79 | — | Data link connector | MAF | Input | Available 0–5 V sensor input | same |
| 80 | Battery backup | same | Permanent +12 V | Input | Dedicated, stores internal log | same |
| 81 | 5 V sensor supply | same | +5 V sensor | Output | Dedicated, sensors only | same |
| 82 | Ignition switch | same | Main relay ignition switch | Input | Dedicated, activates switch 1 input | same |
| 83 | Engine coolant temperature sensor | same | Coolant | Input | Dedicated, 750 Ω pull-up to 5 V | same |
| 84 | Throttle position switch | same | TPS | Input | Dedicated, 100 kΩ pull-up to 5 V | same |
| 85 | Atmospheric pressure sensor | same | Baro volts | Input | Available 0–5 V sensor input | same |
| 86 | Vehicle speed sensor | same | T3 vehicle speed | Input | PnP vehicle speed sensor | same |
| 87 | Throttle position switch | — | CAN1H | — | Dedicated | same |
| 88 | Camshaft position sensor | same | Cam | Input | Dedicated camshaft sensor | same |
| 89 | Crankshaft position sensor | same | Crank | Input | Dedicated crankshaft sensor | same |
| 90 | Volume air flow sensor | same | T4 spare speed | Input | PnP frequency MAF input | same |
| 91 | — | Water spray manual switch | Ground | Output | Dedicated | same |
| 92 | Sensor ground | same | Sensor ground | Output | Dedicated, sensors only | same |
Series 1 migration
AEM lists changed assignments relative to 30-1310 Series 1 hardware. Consult the model-specific comparison and manually check converted calibrations before using 30-6310.