The AEM EMS Series 2 30-6320 is an application-specific standalone plug-in controller. The AEM installation instructions 10-6320 list 2006 Mitsubishi Lancer Evolution IX; 2005–2006 European Evolution IX; and 2003–2004 right-hand-drive European Evolution VIII. The connection schedule below is titled for the 2006 EVO IX; AEM cautions that non-US vehicle harnesses can differ and must be checked against the actual vehicle.

Configuration and operating notes
The manual describes a turbocharged 2.0-litre inline-four application with four sequential injectors, two wasted-spark ignition coils, stepper idle control and Hall-effect crank and cam sensors. It specifies AEMTuner rather than the older AEMPro software. Startup maps are starting points and need tuning for the individual vehicle. The factory MAF/IAT can be used, or the EMS can be configured for MAP-based load; see the manufacturer guide for sensor placement and calibration.
Injector channels 1–6 have 4 A peak / 1 A hold drivers. AEM discusses optionally bypassing the factory injector resistor pack and notes that injector battery compensation changes when it is removed. The guide also describes MIVEC intake cam control for the EVO IX and the fuel-pump controls. AEM states the switch inputs must be switched to ground; applying 12 V may damage the EMS.
The manual's application notes specify an aftermarket wideband and say the factory O2 sensor is not supported, while the pin schedule calls pins 71 and 73 PnP for primary and secondary O2 sensors. Treat this as a source discrepancy and confirm sensor compatibility and calibration with AEM. The source lists PW 1 at both pins 56 and 67; this is reproduced without assuming the two positions are independent.
Connector schedule — 2006 Mitsubishi EVO IX
From the AEM connection chart, pages 9–11, checked against the original page images, including wrapped driver-current notes. Use the connector drawing in the manufacturer instructions to establish pin orientation. PnP denotes a configured but reassignable channel; available denotes a currently unallocated channel; dedicated denotes a fixed assignment. A dash reproduces an empty or dashed source entry and does not establish safe use. Positions 36–40 and 69–70 are not included in the source schedule. Pin 18's printed note ends after “coolant”; no missing text has been inferred. Confirm the specific hardware, wiring and calibration before making changes.
Pins 1–35
| Pin | 2006 Mitsubishi EVO IX harness | AEM EMS 30-6320 | I/O | AEM notes |
|---|---|---|---|---|
| 1 | No. 1 injector | P&H injector 1 | Output | Injector 1, peak/hold 4 A/1 A |
| 2 | No. 4 injector | P&H injector 4 | Output | Injector 4, peak/hold 4 A/1 A |
| 3 | Front heated oxygen sensor heater | Low side driver 1 | Output | Available switched ground, 1.5 A maximum |
| 4 | — | PW 3 | Output | Available switched ground, 1.5 A maximum |
| 5 | Secondary air control solenoid valve (European EVO only) | Idle 5 | Output | Available switched ground, 1.5 A maximum |
| 6 | EGR vacuum solenoid (US only) / wastegate solenoid 2 (European EVO only) | Injector 8 | Output | Available switched ground, 1.5 A maximum |
| 7 | — | — | — | — |
| 8 | Generator G terminal | Injector 7 | Output | PnP alternator control |
| 9 | No. 2 injector | P&H injector 2 | Output | Injector 2, peak/hold 4 A/1 A |
| 10 | — | Injector 5 | Output | Available switched ground, 1.5 A maximum |
| 11 | Ignition power transistor coil 1 and 4 | Coil 1 | Output | PnP coil 1 / coil 1B |
| 12 | Ignition power transistor coil 2 and 3 | Coil 2 | Output | PnP coil 2 / coil 2B |
| 13 | — | CAN1H | — | Dedicated |
| 14 | Stepper motor coil A1 | Idle 1 | Output | PnP stepper idle motor |
| 15 | Stepper motor coil B1 | Idle 3 | Output | PnP stepper idle motor |
| 16 | Evaporative emission purge solenoid | Idle 7 | Output | Available switched ground, 1.5 A maximum |
| 17 | — | Injector 11 | Output | Available switched ground, 1.5 A maximum |
| 18 | Fan control module | Low side driver 9 | Output | Source note ends “User 1 PW output, coolant”; remainder not shown |
| 19 | Volume airflow sensor reset signal | Injector 9 | Output | PnP volume airflow sensor |
| 20 | A/C compressor clutch relay | Low side driver 6 | Output | PnP A/C |
| 21 | Fuel pump relay | Low side driver 11 | Output | PnP fuel pump control |
| 22 | Malfunction indicator lamp | Low side driver 10 | Output | Available switched ground, 1.5 A maximum |
| 23 | — | High side driver 1 | Output | Available switched 12 V, 1.5 A maximum |
| 24 | No. 3 injector | P&H injector 3 | Output | Injector 3, peak/hold 4 A/1 A |
| 25 | — | Injector 6 | Output | Available switched ground, 1.5 A maximum |
| 26 | Rear heated oxygen sensor heater | Low side driver 2 | Output | Available switched ground, 1.5 A maximum |
| 27 | — | PW 1i | Output | Available switched ground, 1.5 A maximum |
| 28 | Stepper motor coil A2 | Idle 2 | Output | PnP stepper idle motor |
| 29 | Stepper motor coil B2 | Idle 4 | Output | PnP stepper idle motor |
| 30 | Condenser fan relay high | Low side driver 3 | Output | PnP fan control |
| 31 | Condenser fan relay low | Low side driver 5 | Output | PnP fan control |
| 32 | Oil feeder control valve | Injector 10 | Output | PnP MIVEC VVC |
| 33 | — | CAN1L | — | Dedicated |
| 34 | Sensor ground | Sensor ground | Output | Dedicated; sensors only |
| 35 | Evaporative emission ventilation solenoid | Low side driver 8 | Output | Available switched ground, 1.5 A maximum |
Pins 41–68
| Pin | 2006 Mitsubishi EVO IX harness | AEM EMS 30-6320 | I/O | AEM notes |
|---|---|---|---|---|
| 41 | Turbocharger wastegate solenoid | PW 2 | Output | PnP boost control |
| 42 | Sensor supplied voltage | 5 V sensor | Output | Dedicated |
| 43 | Crankshaft position sensor | Crank (T1) | Input | Dedicated |
| 44 | Engine coolant temperature sensor | Coolant | Input | PnP coolant temperature |
| 45 | Tachometer signal | Low side driver 7 | Output | PnP tachometer |
| 46 | Power ground | Power ground | Input | Dedicated |
| 47 | Power supply | Power | Input | Dedicated |
| 48 | Fuel pressure solenoid valve | Low side driver 12 | Output | PnP fuel pressure control |
| 49 | Sensor ground | Sensor ground | Output | Dedicated |
| 50 | Camshaft position sensor | Cam (T2) | Input | Dedicated |
| 51 | Barometric pressure sensor | Baro | Input | PnP barometric pressure |
| 52 | Generator FR terminal | EGT 1 | Input | Available, RTD temperature |
| 53 | Intake camshaft position sensor | Car speed | Input | PnP MIVEC |
| 54 | Power steering pressure switch | Switch 5 | Input | Available; switch must connect to ground |
| 55 | Fuel pump relay 3 (low speed) | Low side driver 4 | Output | PnP fuel pump |
| 56 | Intercooler water spray motor (European EVO only) | PW 1 | Output | PnP intercooler water spray |
| 57 | MFI relay | Main relay (C5) | Output | Dedicated |
| 58 | Power ground | Power ground | Input | Dedicated |
| 59 | Power supply | Power | Input | Dedicated |
| 60 | Battery backup | Permanent power | Input | Dedicated |
| 61 | Volume airflow sensor | Spare speed | Input | PnP air flow meter |
| 62 | Intake air temperature sensor | AIT | Input | PnP air temperature |
| 63 | — | Idle 6 | Output | Available switched ground, 1.5 A maximum |
| 64 | — | Idle 8 | Output | Available switched ground, 1.5 A maximum |
| 65 | A/C switch 2 | Switch 3 | Input | PnP A/C |
| 66 | Intercooler water spray auto switch (European EVO only) | MAF | Input | Available 0–5 V sensor input |
| 67 | Intercooler water spray manual switch (European EVO only) | PW 1 | Output | Available switched ground, 1.5 A maximum |
| 68 | Ignition start switch | Cranking (SW1) | Input | Dedicated |
Pins 71–100
| Pin | 2006 Mitsubishi EVO IX harness | AEM EMS 30-6320 | I/O | AEM notes |
|---|---|---|---|---|
| 71 | Front heated oxygen sensor | O2 1 | Input | PnP primary O2 sensor |
| 72 | — | EGT 2 | Input | Available 0–5 V analogue input |
| 73 | Rear heated oxygen sensor | O2 2 | Input | PnP secondary O2 sensor |
| 74 | — | EGT 3 | Input | Available 0–5 V analogue input |
| 75 | Power ground (European EVO only) | Power ground | Input | Dedicated |
| 76 | — | Coil 4 | Output | Available switched ground, 1.5 A maximum |
| 77 | — | — | — | — |
| 78 | Throttle position sensor | TPS | Input | PnP throttle position |
| 79 | Idle position signal | ADCR13 | Input | Available 0–5 V analogue input |
| 80 | Vehicle speed sensor | Switch 2 | Input | PnP vehicle speed |
| 81 | — | Injector 12 | Output | Available switched ground, 1.5 A maximum |
| 82 | — | — | — | — |
| 83 | A/C switch | Switch 6 | Input | PnP A/C switch |
| 84 | — | High side driver 2 | Output | Available switched 12 V, 1.5 A maximum |
| 85 | Data link connector | PCRX | Input | Available serial connection |
| 86 | — | High side driver 3 | Output | Available switched 12 V, 1.5 A maximum |
| 87 | — | High side driver 4 | Output | Available switched 12 V, 1.5 A maximum |
| 88 | Clutch pedal position switch (US EVO only) | Switch 4 | Input | Available switched input |
| 89 | — | — | — | — |
| 90 | Intercooler water spray combination meter (European EVO only) | Coil 3 | Output | Available switched ground, 1.5 A maximum |
| 91 | Knock sensor | Knock 1 | Input | PnP knock detection |
| 92 | Manifold absolute pressure sensor | MAP | Input | PnP manifold pressure |
| 93 | Fuel tank differential pressure sensor | ADCR11 | Input | Available 0–5 V analogue input |
| 94 | — | PCGND | Input | Available serial connection |
| 95 | Main fuel pump and level sensor (US EVO only) | Knock 2 | Input | Available knock detection |
| 96 | Fuel tank temperature sensor | ADCR14 | Input | Available 0–5 V analogue input |
| 97 | Sub fuel pump and level sensor (US EVO only) | EGT 4 | Input | Available 0–5 V analogue input |
| 98 | Engine immobiliser system | — | — | — |
| 99 | Ignition switch | 12 V switched | Input | Dedicated |
| 100 | Data link connector | PCTX | Output | Available serial connection |
Series 1 conversion
AEM distinguishes this model from Series 1 30-1320. In the conversion chart, pin 17 changes to injector 11 and pin 81 to injector 12, with independent control; pins 13 and 33 become CAN1H and CAN1L. The manual says changed functions generally require manual reconfiguration when converting the older calibration.