The AEM EMS Series 2 30-6620 is an application-specific Nissan plug-in engine-management system. Its installation manual lists Skyline, 300ZX, Maxima, Silvia and 180SX applications, with engine and market restrictions. Check the exact part number, engine, year and loom: the manual cover describes “RB25DETT” and “RB20DETT”, while its connector chart identifies RB25DET and RB20DET; resolve this discrepancy with AEM before applying it to a specific vehicle.

Connector schedule
The following table transcribes all 76 numbered positions listed on pages 9–12 of the AEM 30-6620 installation manual, which labels its connector diagrams “Wire View of AEM EMS”. Positions 61–100 are not listed in that diagram. “←” is the manufacturer’s arrow pointing to the function in the previous vehicle column; a dash or blank is the source entry, not a guarantee of an unused or safe terminal. The source groups several vehicle and engine variants in each vehicle column, so follow each parenthetical restriction.
In its chart the manufacturer requires an AEM replacement trigger disc for the indicated cam/crank inputs. The manual also contains a separate Series 1-to-Series 2 comparison on page 13; do not substitute a Series 1 schedule for this ECU.
| Pin | Skyline RB26DETT / RB25DET / RB20DET | 300ZX VG30DE / VG30DETT; Maxima VE30DE | Silvia S14 SR20DET / S13 CA18DET; 180SX CA18DET | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|---|---|
| 1 | Ignition 1 | Ignition 1 | Ignition 1 | Coil 1 | Output | PnP for Coil 1, 0-5V rising edge trigger |
| 2 | Ignition 5 | Ignition 2 | Ignition 2 | Coil 5 | Output | PnP for Coil 5, 0-5V rising edge trigger |
| 3 | Ignition 3 | Ignition 3 | Ignition 3 (CA18DET only) | Coil 3 | Output | PnP for Coil 3, 0-5V rising edge trigger |
| 4 | AAC Valve | ← | --- | PW 1 | Output | PnP for Idle Air Control, connects to Pin 106 |
| 5 | A/T Control Unit | ← | Wastegate Solenoid (JDM CA18 only) | PW 2 | Output | PnP for Boost control, connects to Pin 25 |
| 6 | Cooling Fan Relay (RB26DETT only) | Cooling Fan Sub Relay (300ZX Turbo Only) | Air Conditioner Relay (CA18DET only) | Low Side 5 | Output | PnP for Cooling Fan (CA18DET only: PnP for AC) |
| 7 | Tachometer | ← | ← | Low Side 7 | Output | PnP for Tachometer, internal pull-up resistor to 12V |
| 8 | --- | AIV Solenoid (90-92 300ZX), Power Solenoid (Maxima) | Variable Butterfly Solenoid (JDM CA18DET only) | Low Side 12 | Output | Available, switched Ground, 1.5A max |
| 9 | Air Conditioner Relay | ← | ← | Low Side 6 | Output | PnP for A/C Compressor |
| 10 | ECM Ground | ← | ← | Power Ground | Input | Dedicated |
| 11 | Ignition 6 | Ignition 4 | Ignition 3 (SR20DET only) Ignition 4 (CA18DET only) | Coil 6 | Output | PnP for Coil 6, 0-5V rising edge trigger |
| 12 | Ignition 2 | Ignition 5 | Ignition 4 (SR20DET only) | Coil 2 | Output | PnP for Coil 2, 0-5V rising edge trigger |
| 13 | Ignition 4 | Ignition 6 | --- | Coil 4 | Output | PnP for Coil 4, 0-5V rising edge trigger |
| 14 | A/T Control Unit | ← | ← | Idle 5 | Output | Avail, switched Ground / +12V, 1.5A Max |
| 15 | A/T Control Unit | ← | ← | Idle 6 | Output | Avail, switched +12V / Ground, 1.5A Max |
| 16 | ECCS Relay control, Ignition Relay control | ← | ← | Main Relay (control) | Output | Dedicated, EMS activates relay with switched GND |
| 17 | --- | Data Link Connector | Data Link Connector | Injector 7 | Output | Avail, Switched Ground, 1.5A max |
| 18 | Fuel Pump Relay Control Signal | ← | ← | Low Side 1 | Output | PnP for Fuel Pump |
| 19 | Power Steering Oil Pressure Switch | Cooling Fan Relay | Cooling Fan Relay (SR20DET only) | Low Side 3 | Output | PnP for Cooling Fan |
| 20 | ECM Ground | ← | ← | Power Ground | Input | Dedicated |
| 21 | Diagnostics Receive Data | ← | ← | EGT 2 | Input | Available, jumper set for 0-5V Input |
| 22 | Diagnostics Transmit Data | ← | ← | Switch 3 | Input | Available, switch must connect to ground |
| 23 | Knock Sensor (Cylinders 1-3) | Knock Sensor | Knock Sensor | Knock 1 | Input | Available, software knock filter |
| 24 | Knock Sensor (Cylinders 4-6) | --- | --- | Knock 2 | Input | Available, software knock filter |
| 25 | Wastegate Valve Control Solenoid Signal | Wastegate Solenoids (300ZX TT Only) | Wastegate Solenoid (SR20DET only) | PW 2 | Output | PnP for Boost control, connects to Pin 5 |
| 26 | Mass Air Flow Sensor Ground | ← | ← | Power Ground | Input | Dedicated |
| 27 | Rear Mass Air Flow Sensor (RB26DETT) | Mass Air Flow Sensor | Mass Air Flow Sensor | MAF | Input | PnP for MAF Sensor |
| 28 | Engine Coolant Temperature Sensor | ← | ← | Coolant | Input | PnP for Engine Coolant Temp |
| 29 | Front Heated Oxygen Sensor Signal | Right Side Heated Oxygen Sensor | Heated Oxygen Sensor Signal | O2 #1 | Input | Dedicated, 0-5V signal |
| 30 | Sensor Ground | ← | ← | Sensor Ground | Output | Dedicated |
| 31 | Diagnostics Clock | ← | ← | EGT 3 | Input | Available, jumper set for 0-5V Input |
| 32 | Malfunction Indicator Lamp | ← | ← | Low Side Driver 10 | Output | Avail, Switched Ground, 1.5A Max |
| 33 | Exhaust Temperature Light (RB25DET Only) | FICD Solenoid (300ZX Only) | Cooling Fan Hi Speed (SR20DET) / Diagnostics (CA18DET) | Injector 8 | Output | PnP for Cooling Fan |
| 34 | Front Mass Air Flow Ground (RB26DETT) | Power Steering Oil Press sw | Power Steering Oil Press sw (SR20DET Only) | Switch 2 | Input | Available, switch must connect to ground |
| 35 | Front Mass Air Flow Signal (RB26DETT) | Fuel Pump Voltage Control (300ZX Turbo Only) | Boost Pressure Sensor (SR20DET Only) | MAP | Input | Available, use this pin for Speed Density conversion |
| 36 | IAT Sensor (RB26) / FICD solenoid (RB25) | Fuel Temperature Sensor (300ZX Only) | --- | AIT | Input | Avail, Air Temperature, 2.2kΩ pull-up resistor |
| 37 | --- | --- | Mass Air Flow Pin D (CA18DET-Non Catalytic Model Only) | ADCR14 | Input | Avail, 0-5 Volt Input |
| 38 | Throttle Position Sensor | ← | ← | TPS | Input | PnP for Throttle Position signal |
| 39 | --- | EGR Temperature Sensor | --- | EGT 1 | Input | Available, jumper set for 0-5V Input |
| 40 | --- | --- | --- | CAN1H | --- | Dedicated |
| 41 | Camshaft Position Sensor Reference Signal | ← | ← | Cam Signal | Input | Dedicated, must use AEM replacement trigger disc (connects to pin 51) |
| 42 | Camshaft Position Sensor Signal | ← | ← | Crank Signal | Input | Dedicated, must use AEM replacement trigger disc (connects to pin 52) |
| 43 | Ignition Switch (start position) | ← | ← | +12V starting power | Input | Dedicated |
| 44 | Neutral Position Switch | ← | ← | Switch 4 | Input | Available, switch must connect to ground |
| 45 | Ignition Switch | ← | ← | Main relay (input) | Input | Dedicated, +12V activates Main Relay circuit |
| 46 | Air Conditioner Switch | ← | ← | Switch 6 | Input | PnP for A/C request switch |
| 47 | Diagnostics Check Signal | ← | ← | EGT 4 | Input | Available, jumper set for 0-5V Input |
| 48 | +5V Sensor reference power | ← | ← | +5V Sensor | Output | Dedicated |
| 49 | Power Supply For ECM | ← | ← | +12V Switched | Input | Dedicated, +12V power when ECCS Relay is on |
| 50 | ECM Ground | ← | ← | Power Ground | Input | Dedicated |
| 51 | Camshaft Position Reference Signal | ← | ← | Cam Signal | Input | Dedicated, must use AEM replacement trigger disc (connects to pin 41) |
| 52 | Camshaft Position Sensor Signal | ← | ← | Crank Signal | Input | Dedicated, connects to Pin 42 |
| 53 | Vehicle Speed Sensor Signal | ← | ← | T3 (Vehicle Speed) | Input | PnP for Vehicle Speed Sensor |
| 54 | Idle Position Switch | ← | ← | Switch 1 | Input | Available, switch must connect to ground |
| 55 | Rear Heated Oxygen Sensor (RB26DETT) | Left Side Heated Oxygen Sensor | A/C FICD (CA18DET Only) | O2 #2 | Input | Dedicated, 0-5V signal |
| 56 | Throttle Sensor Output Signal | Throttle Sensor Output Signal (Auto Trans only) | Throttle Sensor Output Signal (Auto Trans only) | TPS Out | Output | Dedicated, for use with GT-R auxiliary devices (Attesa AWD control, Dashboard display) |
| 57 | Power source for Idle Position switch | ← | Power for Idle Position switch (CA18DET) | CAN1L | Output | Dedicated |
| 58 | Power Supply Back-Up | ← | ← | Permanent +12V | Input | Dedicated, backup power for internal datalog |
| 59 | Power Supply for ECM | ← | ← | +12V Switched | Input | Dedicated, +12V power when ECCS Relay is on |
| 60 | ECM Ground | ← | ← | Power Ground | Input | Dedicated |
| 101 | Injector 1 | Injector 1 | Injector 1 | Injector 1 | Output | PnP for Injector 1 (Peak & Hold 4A/1A driver) |
| 102 | --- | EGR Control Solenoid Valve | EGR Control Solenoid Valve (SR20DET only) | Injector 12 | Output | Avail, Switched Ground, 1.5A max (not Peak&Hold) |
| 103 | Injector 3 | Injector 3 | Injector 3 | Injector 3 | Output | PnP for Injector 3 (Peak & Hold 4A/1A driver) |
| 104 | Fuel Pump Voltage Control | ← | --- | ADCR11 | Input | Available, 0-5 Volt Input |
| 105 | Injector 2 | Injector 5 | --- | Injector 2 | Output | PnP for Injector 2 (Peak & Hold 4A/1A driver) |
| 106 | Fuel Pump Voltage Control-2 (RB26DETT) | --- | AAC Solenoid Valve | PW 1 | Output | PnP for Idle Air Control, connects to Pin 4 |
| 107 | ECM Ground | ← | ← | Power Ground | Input | Dedicated |
| 108 | ECM Ground | ← | ← | Power Ground | Input | Dedicated |
| 109 | Back Electromotive Current Feedback Circuit | Power Supply For ECM | Power (CA18) / Back-Up Power (SR20) | --- | --- | Not Used |
| 110 | Injector 5 | Injector 2 | Injector 2 | Injector 5 | Output | PnP for Injector 5 (Peak & Hold 4A/1A driver) |
| 111 | --- | PRVR Control Solenoid Valve | PRVR Control Solenoid Valve (CA18) | Injector 9 | Output | Avail, Switched Ground, 1.5A max (not Peak&Hold) |
| 112 | Injector 6 (RB20: Inj 4) | Injector 4 | Injector 4 | Injector 6 | Output | PnP for Injector 6 (Peak & Hold 4A/1A driver) |
| 113 | VTC Solenoid Valve (RB25DET) | VTC Solenoid Valves | VTC Solenoid Valve (SR20DET only) | Injector 11 | Output | Avail, Switched Ground, 1.5A max (not Peak&Hold) |
| 114 | Injector 4 (RB20: Inj 6) | Injector 6 | --- | Injector 4 | Output | PnP for Injector 4 (Peak & Hold 4A/1A driver) |
| 115 | Oxygen Sensor Heater Control Signal | ← | ← | Injector 10 | Output | Avail, Switched Ground, 1.5A max (not Peak&Hold) |
| 116 | ECM Ground | ← | ← | Power Ground | Input | Dedicated |
Source
AEM 30-6620 Series 2 installation instructions and wiring chart; AEM engine management support archive.