Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Dynamometers
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 9 to revision 14

Removed text is struck through; added text is highlighted.

A dynamometer, often shortened to dyno, is equipment used to measure torque and rotational speed, or to infer power from a known accelerating inertia. In automotive work it can test an engine on a stand, a vehicle on rollers, or a vehicle coupled at its wheel hubs. A controllable power absorber can also impose load, allowing the operator to investigate operating points that a simple acceleration-only test cannot hold.

This section explains the machinery, measurement and control behind the figures. The installation, absorber, measuring system and controller are separate choices: for example, an eddy-current brake can be fitted to an engine, rolling-road or hub installation. See all Dynamometers articles.

Three test layouts and their measurement boundaries. Arrows show power flow during drive; sensor location varies. Original schematic created for Tuning Wiki, CC BY 4.0.

Explore the section

Rolling road chassis dynamometersMotorcycle and powersports dynamometersEngine dynamometersHub dynamometersHydraulic hub dynamometersEddy-current hub dynamometersElectric motor and regenerative hub dynamometersCompare hydraulic, eddy-current and electric hub dynamometersOn-car and portable dynamometersInertia dynamometersEddy-current dynamometersWater and oil hydraulic dynamometer brakesElectric motor and generator dynamometersDynamometer control systemsOriginal equipment dynamometer control systemsCompare factory and aftermarket dynamometer controllersMeasurement and interpreting resultsDyno graphs explainedDynamometer calibration and verificationTest setup and safetyDynamometer manufacturers and suppliersUK dynamometer rebuilders and refurbishmentRolling road chassis dynamometersEngine dynamometersHub dynamometersHydraulic hub dynamometersEddy-current hub dynamometersElectric motor and regenerative hub dynamometersCompare hydraulic, eddy-current and electric hub dynamometersOn-car and portable dynamometersInertia dynamometersEddy-current dynamometersWater and oil hydraulic dynamometer brakesElectric motor and generator dynamometersDynamometer control systemsOriginal equipment dynamometer control systemsMeasurement and interpreting resultsTest setup and safetyDynamometer manufacturers and suppliersUK dynamometer rebuilders and refurbishment

Torque, speed and power

Torque is a turning moment, measured here in newton metres (N·m). Rotational speed is measured in revolutions per minute (rpm). At the same shaft and instant, mechanical power is P = T × ω, where T is torque in N·m and ω is angular speed in radians per second. Equivalently, power (kW) = torque (N·m) × rpm ÷ 9,549.3. Torque alone is not power: the speed at which it is produced matters. A brake's reaction force can be measured with a load cell at a known lever arm, or a shaft torque transducer can be used. For transient tests, torque and speed need to be time-aligned; 40 CFR 1065.15 describes synchronous speed and brake-torque measurement for engine work.

An inertia dyno instead uses the acceleration of a rotating mass whose moment of inertia is known. The simple relationship is net torque = inertia × angular acceleration. Losses and the inertia of coupled parts must be dealt with according to the measurement system; it is not a direct steady-state torque measurement.

Where the measurement is made

InstallationConnection and normal measurement boundaryTypical use Engine dynoEngine output shaft coupled to a test-cell absorber; gearbox and driven wheels normally excluded.Engine development, calibration and controlled durability tests. Rolling road or chassis dynoDriven tyres turn rollers; the transmission, final drive and tyre/roller interface are in the power path.Whole-vehicle tuning, diagnosis, emissions or road-load simulation. Hub dynoDriven wheels are removed and absorbers attach at the hubs; the gearbox and final drive remain in the power path.Vehicle testing without the driven tyre-to-roller contact. On-road or on-car systemDepending on the product, this may mean a portable vehicle-attached dyno or a road-performance instrument estimating power from vehicle motion and assumptions.Mobile testing and comparison; identify exactly what the equipment measures.

These boundaries matter. Wheel or hub output cannot automatically be called crankshaft output. Transmission losses vary with operating conditions, and any calculated crank figure depends on its loss model and test procedure. Different dynos, tyre conditions, gearing, temperatures and correction standards can give different numbers; a repeatable before-and-after comparison needs the method and conditions recorded.

How load is produced

Inertia: the engine accelerates a calibrated rotating mass. Acceleration rate is determined by net torque and inertia, rather than independently commanded by a brake. Eddy current: relative motion and an excited magnetic field induce currents in conductive brake parts; their reaction resists motion and the absorbed energy becomes heat. Water brake: a rotor transfers momentum to water in a housing. Fluid movement and turbulence turn shaft work into heat, which the water removes. Oil-hydraulic: a pump drives oil against a controlled pressure difference. Oil flow, pressure control and cooling determine the operating envelope. Electric machine: a controlled motor/generator can absorb power electrically; an appropriately equipped system can also drive the test shaft. Energy may be dissipated or returned to the electrical supply, depending on the installation. Mechanical friction: historical friction brakes use a rubbing element and measure reaction force. Heat and wear limit continuous use.Inertia: the engine accelerates a calibrated rotating mass. Acceleration rate is determined by net torque and inertia, rather than independently commanded by a brake. Eddy current: an electrically excited magnetic field induces currents in a moving conductor; their reaction resists motion and the absorbed energy becomes heat. Water brake: a rotor transfers momentum to water in a housing. Fluid movement and turbulence turn shaft work into heat, which the water removes. Oil-hydraulic: a pump drives oil against a controlled pressure difference. Oil flow, pressure control and cooling determine the operating envelope. Electric machine: a controlled motor/generator can absorb power electrically; an appropriately equipped system can also drive the test shaft. Energy may be dissipated or returned to the electrical supply, depending on the installation. Mechanical friction: historical friction brakes use a rubbing element and measure reaction force. Heat and wear limit continuous use.

The absorber's torque, speed, cooling and continuous-duty limits all matter. Maximum power at one speed does not mean the same maximum torque is available throughout the speed range. A passive absorber cannot drive the test shaft or hold substantial power indefinitely at zero speed.

What a test can show

An acceleration sweep records output as speed rises; acceleration rate, rotating inertia, filtering and heat conditions influence the result. A steady-state test uses a suitable load absorber and controller to hold an operating point while the operator examines torque, fuelling or other measurements. A road-load simulation applies a speed-dependent load to approximate driving resistance, sometimes with simulated inertia. The US EPA describes how coastdown-derived road load is apportioned between vehicle losses and dynamometer settings in its road-load analysis.

Preparation is part of the measurement: inspect the vehicle and test equipment, use the manufacturer's restraint and cooling arrangements, extract exhaust, and monitor temperatures and operating limits. Record the gear, tyre and restraint conditions where applicable, correction method, environmental readings, test mode and calibration. An appropriate vehicle test mode and compatible axle configuration are particularly important for modern four-wheel-drive and stability systems.

Further reading

Mustang Dynamometer MD-600 manual — a real chassis dyno installation, load measurement and operating guidance. US engine-test work determination — synchronised torque and speed. EPA: isolating road-load losses — coastdown and chassis-dyno load setting. Magicmotorsport DynoRoad — an existing wiki page about one portable road-performance instrument.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 9: Dynamometers

A dynamometer, often shortened to dyno, is equipment used to measure torque and rotational speed, or to infer power from a known accelerating inertia. In automotive work it can test an engine on a stand, a vehicle on rollers, or a vehicle coupled at its wheel hubs. A controllable power absorber can also impose load, allowing the operator to investigate operating points that a simple acceleration-only test cannot hold.

This section explains the machinery, measurement and control behind the figures. The installation, absorber, measuring system and controller are separate choices: for example, an eddy-current brake can be fitted to an engine, rolling-road or hub installation. See all Dynamometers articles.

Engine, rolling-road and hub dynamometer power paths, showing where the drivetrain, tyre contact and measurement lie.
Three test layouts and their measurement boundaries. Arrows show power flow during drive; sensor location varies. Original schematic created for Tuning Wiki, CC BY 4.0.

Explore the section

Torque, speed and power

Torque is a turning moment, measured here in newton metres (N·m). Rotational speed is measured in revolutions per minute (rpm). At the same shaft and instant, mechanical power is P = T × ω, where T is torque in N·m and ω is angular speed in radians per second. Equivalently, power (kW) = torque (N·m) × rpm ÷ 9,549.3. Torque alone is not power: the speed at which it is produced matters. A brake's reaction force can be measured with a load cell at a known lever arm, or a shaft torque transducer can be used. For transient tests, torque and speed need to be time-aligned; 40 CFR 1065.15 describes synchronous speed and brake-torque measurement for engine work.

An inertia dyno instead uses the acceleration of a rotating mass whose moment of inertia is known. The simple relationship is net torque = inertia × angular acceleration. Losses and the inertia of coupled parts must be dealt with according to the measurement system; it is not a direct steady-state torque measurement.

Where the measurement is made

InstallationConnection and normal measurement boundaryTypical use
Engine dynoEngine output shaft coupled to a test-cell absorber; gearbox and driven wheels normally excluded.Engine development, calibration and controlled durability tests.
Rolling road or chassis dynoDriven tyres turn rollers; the transmission, final drive and tyre/roller interface are in the power path.Whole-vehicle tuning, diagnosis, emissions or road-load simulation.
Hub dynoDriven wheels are removed and absorbers attach at the hubs; the gearbox and final drive remain in the power path.Vehicle testing without the driven tyre-to-roller contact.
On-road or on-car systemDepending on the product, this may mean a portable vehicle-attached dyno or a road-performance instrument estimating power from vehicle motion and assumptions.Mobile testing and comparison; identify exactly what the equipment measures.

These boundaries matter. Wheel or hub output cannot automatically be called crankshaft output. Transmission losses vary with operating conditions, and any calculated crank figure depends on its loss model and test procedure. Different dynos, tyre conditions, gearing, temperatures and correction standards can give different numbers; a repeatable before-and-after comparison needs the method and conditions recorded.

How load is produced

  • Inertia: the engine accelerates a calibrated rotating mass. Acceleration rate is determined by net torque and inertia, rather than independently commanded by a brake.
  • Eddy current: an electrically excited magnetic field induces currents in a moving conductor; their reaction resists motion and the absorbed energy becomes heat.
  • Water brake: a rotor transfers momentum to water in a housing. Fluid movement and turbulence turn shaft work into heat, which the water removes.
  • Oil-hydraulic: a pump drives oil against a controlled pressure difference. Oil flow, pressure control and cooling determine the operating envelope.
  • Electric machine: a controlled motor/generator can absorb power electrically; an appropriately equipped system can also drive the test shaft. Energy may be dissipated or returned to the electrical supply, depending on the installation.
  • Mechanical friction: historical friction brakes use a rubbing element and measure reaction force. Heat and wear limit continuous use.

The absorber's torque, speed, cooling and continuous-duty limits all matter. Maximum power at one speed does not mean the same maximum torque is available throughout the speed range. A passive absorber cannot drive the test shaft or hold substantial power indefinitely at zero speed.

What a test can show

An acceleration sweep records output as speed rises; acceleration rate, rotating inertia, filtering and heat conditions influence the result. A steady-state test uses a suitable load absorber and controller to hold an operating point while the operator examines torque, fuelling or other measurements. A road-load simulation applies a speed-dependent load to approximate driving resistance, sometimes with simulated inertia. The US EPA describes how coastdown-derived road load is apportioned between vehicle losses and dynamometer settings in its road-load analysis.

Preparation is part of the measurement: inspect the vehicle and test equipment, use the manufacturer's restraint and cooling arrangements, extract exhaust, and monitor temperatures and operating limits. Record the gear, tyre and restraint conditions where applicable, correction method, environmental readings, test mode and calibration. An appropriate vehicle test mode and compatible axle configuration are particularly important for modern four-wheel-drive and stability systems.

Further reading

Revision 14: Dynamometers

A dynamometer, often shortened to dyno, is equipment used to measure torque and rotational speed, or to infer power from a known accelerating inertia. In automotive work it can test an engine on a stand, a vehicle on rollers, or a vehicle coupled at its wheel hubs. A controllable power absorber can also impose load, allowing the operator to investigate operating points that a simple acceleration-only test cannot hold.

This section explains the machinery, measurement and control behind the figures. The installation, absorber, measuring system and controller are separate choices: for example, an eddy-current brake can be fitted to an engine, rolling-road or hub installation. See all Dynamometers articles.

Engine, rolling-road and hub dynamometer power paths, showing where the drivetrain, tyre contact and measurement lie.
Three test layouts and their measurement boundaries. Arrows show power flow during drive; sensor location varies. Original schematic created for Tuning Wiki, CC BY 4.0.

Explore the section

Torque, speed and power

Torque is a turning moment, measured here in newton metres (N·m). Rotational speed is measured in revolutions per minute (rpm). At the same shaft and instant, mechanical power is P = T × ω, where T is torque in N·m and ω is angular speed in radians per second. Equivalently, power (kW) = torque (N·m) × rpm ÷ 9,549.3. Torque alone is not power: the speed at which it is produced matters. A brake's reaction force can be measured with a load cell at a known lever arm, or a shaft torque transducer can be used. For transient tests, torque and speed need to be time-aligned; 40 CFR 1065.15 describes synchronous speed and brake-torque measurement for engine work.

An inertia dyno instead uses the acceleration of a rotating mass whose moment of inertia is known. The simple relationship is net torque = inertia × angular acceleration. Losses and the inertia of coupled parts must be dealt with according to the measurement system; it is not a direct steady-state torque measurement.

Where the measurement is made

InstallationConnection and normal measurement boundaryTypical use
Engine dynoEngine output shaft coupled to a test-cell absorber; gearbox and driven wheels normally excluded.Engine development, calibration and controlled durability tests.
Rolling road or chassis dynoDriven tyres turn rollers; the transmission, final drive and tyre/roller interface are in the power path.Whole-vehicle tuning, diagnosis, emissions or road-load simulation.
Hub dynoDriven wheels are removed and absorbers attach at the hubs; the gearbox and final drive remain in the power path.Vehicle testing without the driven tyre-to-roller contact.
On-road or on-car systemDepending on the product, this may mean a portable vehicle-attached dyno or a road-performance instrument estimating power from vehicle motion and assumptions.Mobile testing and comparison; identify exactly what the equipment measures.

These boundaries matter. Wheel or hub output cannot automatically be called crankshaft output. Transmission losses vary with operating conditions, and any calculated crank figure depends on its loss model and test procedure. Different dynos, tyre conditions, gearing, temperatures and correction standards can give different numbers; a repeatable before-and-after comparison needs the method and conditions recorded.

How load is produced

  • Inertia: the engine accelerates a calibrated rotating mass. Acceleration rate is determined by net torque and inertia, rather than independently commanded by a brake.
  • Eddy current: relative motion and an excited magnetic field induce currents in conductive brake parts; their reaction resists motion and the absorbed energy becomes heat.
  • Water brake: a rotor transfers momentum to water in a housing. Fluid movement and turbulence turn shaft work into heat, which the water removes.
  • Oil-hydraulic: a pump drives oil against a controlled pressure difference. Oil flow, pressure control and cooling determine the operating envelope.
  • Electric machine: a controlled motor/generator can absorb power electrically; an appropriately equipped system can also drive the test shaft. Energy may be dissipated or returned to the electrical supply, depending on the installation.
  • Mechanical friction: historical friction brakes use a rubbing element and measure reaction force. Heat and wear limit continuous use.

The absorber's torque, speed, cooling and continuous-duty limits all matter. Maximum power at one speed does not mean the same maximum torque is available throughout the speed range. A passive absorber cannot drive the test shaft or hold substantial power indefinitely at zero speed.

What a test can show

An acceleration sweep records output as speed rises; acceleration rate, rotating inertia, filtering and heat conditions influence the result. A steady-state test uses a suitable load absorber and controller to hold an operating point while the operator examines torque, fuelling or other measurements. A road-load simulation applies a speed-dependent load to approximate driving resistance, sometimes with simulated inertia. The US EPA describes how coastdown-derived road load is apportioned between vehicle losses and dynamometer settings in its road-load analysis.

Preparation is part of the measurement: inspect the vehicle and test equipment, use the manufacturer's restraint and cooling arrangements, extract exhaust, and monitor temperatures and operating limits. Record the gear, tyre and restraint conditions where applicable, correction method, environmental readings, test mode and calibration. An appropriate vehicle test mode and compatible axle configuration are particularly important for modern four-wheel-drive and stability systems.

Further reading