Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

What changes with a turbo upgrade?

Scope: These are EA888 Simos 18 examples, mainly 18.1. Exact ECU hardware, engine, transmission, software, calibration and patches determine whether a function or definition applies. Community labels are research leads: confirm the target A2L, axes, units, scaling, selectors and logs. Neither listed names nor file ranges are recommended settings.

A hybrid, IS20-to-IS38 swap or larger turbo changes the relationship between requested air charge, exhaust energy, wastegate position and delivered pressure. The EcuTek EA888 Mk7 tuning guide describes the torque-oriented air path and fast ignition/fuel path. The calibration, fuel supply, intake charge temperatures, pressure measurement and transmission must be assessed together, not treated as a single boost target.

Establish the hardware and baseline

Record the original and new turbo, compressor and turbine, actuator type, vacuum or electronic control, fuel and injection hardware, ECU/TCU identifiers, installed boost patches, sensors and intercooler. Verify actuator travel and adaptation using the hardware supplier's instructions, inspect leaks and exhaust restrictions, and diagnose pre-existing faults. Use a recoverable original and the correct file definition.

Before a high-load comparison, check that pressure and temperature channels are plausible, lambda and fuel pressure follow their targets, and knock and intervention states can be observed. Requested and actual pressures must refer to the same location and both be absolute or both gauge. Record gear, rpm, temperature, fuel and calibration for each comparison.

Air, torque and protection

In the bri3d a2l2xdf community definition list, ip_put_sp is labelled upstream-throttle pressure setpoint; ip_pq_cha_max is labelled maximum turbo pressure ratio. In the SC8S5031_C_OEM community A2L cross-reference, one SC8S5031 pressure-setpoint example has rpm and intake-manifold pressure setpoint axes. This does not establish the same axes or map selection for another ASW. Refer to the separate torque-model guide for air-charge and torque maps.

The same community list labels ip_n_tcha_stnd as turbocharger speed, ip_pq_cha_surge_dl as a compressor surge line, and c_n_tcha_max_sp / c_n_tcha_max as turbo-speed management thresholds. The SC8S5031 compressor-model reference lists n_cmpr_mdl as a modelled speed signal and ip_n_tcha_stnd as a speed lookup. Values derived from an OEM compressor model are not necessarily measured shaft speed and need not describe a replacement turbo. The simos.app Easy Wastegate guide warns that bypassing or raising model-based protections can leave the actual turbo unprotected; physical speed and temperature limits still matter.

Pressure-ratio and compressor-model maps

The following axes and signal names describe the SC8S5031_C_OEM community cross-reference. Its automatically matched captions and some indexes can be inconsistent; use the target file's matching A2L and software documentation to verify each entry. They are not proven to apply to 18.6, 18.10 or every 18.1 calibration.

  • ip_pq_cha_max is described as a maximum compressor pressure-ratio map, indexed by engine speed and compressor-inlet air temperature tia_cha_up in this example. Its output is a dimensionless ratio, not a boost value in hPa. See the pressure-setpoint application reference.
  • ip_pq_cha_surge_dl is a surge-boundary pressure-ratio curve in the surge-detection reference. Its axis reference has reduced compressor-inlet volumetric-flow units, but the extracted input is marked NO_INPUT_QUANTITY; confirm the actual lookup signal. A separate hysteresis entry is listed with conflicting idle/part-load descriptions. Compare the actual compressor's operating map and the ECU model; this is not simply a higher-boost target.
  • ip_n_tcha_stnd relates reduced upstream volumetric flow and compressor pressure ratio to a standardised speed lookup; n_cmpr_mdl is a runtime modelled speed in the compressor-model reference. Neither label establishes that a physical turbo-speed sensor is fitted.
  • c_tia_thr_tcha_max_sp and c_tia_thr_tcha_max are temperature-related protection thresholds; lv_tia_thr_tcha_max_prot is a runtime flag in the charge-air temperature protection reference. Check the definition and whether the underlying temperature is modelled.
  • ip_teg_tur_up_sp appears in a lambda-based turbine-overheat path; ip_tqi_teg_max_tur_min appears in a separate torque-based path. Do not treat either representational range as an exhaust-component rating.

A replacement turbo can make the factory model inaccurate. Simply moving a model-based threshold out of the way does not make the new compressor or turbine safe; establish appropriate physical speed and temperature limits and a suitable way to monitor or protect them.

MAP and upstream-throttle sensor scaling

In the SC8S5031 pressure-determination reference, ip_prs_im_mes is the manifold-pressure conversion curve and ip_prs_up_thr_mes is the separate upstream-throttle conversion curve. The example uses their respective sensor-voltage inputs and hPa outputs. vp_prs_im_sens, vp_prs_up_thr_sens and prs_up_thr_mmv are runtime measurements, not conversion maps. Check the exact sensor part, wiring, transfer curve, usable low-pressure and high-pressure range, and any temperature element before treating a higher-range replacement as calibrated.

Compare plausible engine-off readings with a suitable barometric reference and verify pressure and temperature over the relevant operating range against appropriate independent measurements. A dual-sensor swap discussion reports acceptable-looking pressure but poor running; a temperature-sensor mismatch was suspected, not conclusively established. Channel clipping is also not by itself proof that a sensor has reached its physical limit.

For the separate MAP and upstream-throttle sensor conversion curves, replacement checks and logging, see Simos 18 MAP and boost pressure sensors.

Separating target, response and intervention

First check whether the torque and cylinder-air request reach the intended operating region, and whether PUT target is itself limited. Then compare PUT target and measured PUT, actuator command and position, and the available turbo-protection flags over the same event. A target that falls and an actual pressure that fails to follow a steady target are different symptoms. Confirm each sensor's location, pressure reference and range, and repeat under comparable conditions before changing a map. The torque-model guide details the different forward and reverse map axes.

Work through the symptom

Log rpm, gear, pedal, torque request/limit and estimated torque; actual and requested upstream-throttle/manifold pressure; air-charge request/estimate; wastegate target and position; intake temperature, lambda target/actual, ignition and cylinder corrections; rail-pressure target/actual and relevant states. Check the sample rate and channel definitions. A low pressure target suggests a different investigation from a high target that the hardware cannot reach; a mismatch alone does not prove an actuator map is wrong.

A hybrid-turbo case reports boost-control and rail-pressure issues and later improvement following model/pre-control changes. It is one owner's report, not a transferable IS38 map or proven universal remedy. Compare controlled operating points, not a different car's table values.

Detailed Simos 18 guides: torque model calibration · DSG torque coordination.

Detailed valve-train guides: camshaft timing · valve lift tuning.

Detailed air-path guides: air charge modelling · throttle control.

For speed-model, surge and temperature protections on a replacement turbo, see Simos 18 turbocharger protection.

For compressor-side bypass operation, surge-related requests and N249 diagnosis, see Simos 18 turbo diverter and recirculation valve control.

Related guides: bigger turbos · wastegate and boost control · fuel-system and MPI upgrades · ethanol and flex fuel · torque model and DSG · ignition and knock · launch control · rolling anti-lag.

For aftermarket water/methanol systems and verifying the fault-response path, see Simos 18 water methanol injection and failsafe.

References reviewed 17 November 2026. Forum accounts are reported observations, not independently verified fixes.

For measured intercooler comparisons and charge-air temperature-model examples, see Simos 18 intercooler and charge-air cooling upgrades.

For electric actuator stop learning, feedback signals and P00AF/P2563 investigation, see Simos 18 electric wastegate actuator adaptation and diagnosis.

For turbine and catalyst pressure locations, model names and restriction checks, see Simos 18 exhaust pressure modelling and restriction diagnosis.

For tuned EA888 plug selection and ignition-hardware diagnosis, see Simos 18 spark plugs, coils and tuned-engine misfire diagnosis.

For pre-turbo restriction, airflow tests and air-cleaner model examples, see Simos 18 intake and turbo inlet upgrades.

For EA888 exhaust hardware and source-qualified downpipe and cat-back comparisons, see Simos 18 exhaust and downpipe upgrades.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.