Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Exhaust changes and the Simos 18 air path

On a turbocharged EA888, a downpipe begins at the turbine outlet; a cat-back system is farther downstream. They can change noise and exhaust-side restriction at different locations. A larger pipe, a different catalyst or an altered silencer does not by itself establish a particular power gain or a suitable boost calibration. Identify the exact vehicle, engine, ECU ASW/CAL, turbo, catalyst/particulate-filter equipment and replacement system. Volkswagen SSP 522 describes the integrated manifold and turbine arrangement for its CHHA/CHHB example, not every Simos 18 vehicle.

Hardware changes can affect turbine expansion, boost response and the exhaust-pressure model. Before using any tune, confirm the tuning supplier's specific supported software, turbo, fuel and exhaust configuration. For example, COBB's Mk7 GTI and Golf R table lists stock or specified cat-back exhausts for its described stages; it is an example of that supplier's product requirements, not a universal definition of “Stage 2.”

What pressure and temperature maps represent

The following are research examples from the community SC8S5031_C_OEM Simos 18.1 exhaust-pressure reference. Confirm ASW/CAL, exhaust configuration, hardware index, units and active branch. An ECU-estimated pressure is not a physical pressure measurement, and representable limits are not hardware ratings.

  • ip_prs_ex_pcat_inc_1[3] is labelled a catalyst-flow pressure-increase model against mfl_sum_cat in kg/h and ambient pressure amp in hPa. A different downpipe or catalyst may change the physical relationship; the map alone does not tell you the real pressure drop of the replacement.
  • ip_pq_tur_1_ref[1] is a turbine pressure-quotient model against engine speed and an air-mass-labelled axis; the second input has NO_INPUT_QUANTITY metadata. Establish the source and quotient direction before interpreting it.
  • ip_pq_tur_l_bpa_open and ip_pq_tur_l_bpa_close concern low-load turbine quotient for wastegate states. Their kg/h- and hPa-labelled axes lack explicit input quantities, and an adjacent copied caption conflicts with the open label. Check the actual function and selection on the matched file.
  • ratio_prs_ex is a runtime current-to-reference exhaust-pressure ratio, and prs_ex_pcat_up_dyn is a pre-catalyst model-path pressure. Neither proves a physical sensor is fitted. See the separate exhaust-pressure guide for their limitations and more calibration examples.

Turbo speed, turbine/catalyst temperature and lambda protection remain separate concerns. A changed exhaust can make stock model assumptions less representative; raising a limit or suppressing a fault does not establish physical margin. Compare matched pressure requests and actuals, wastegate request and feedback, lambda target and actual, fuel pressures and relevant temperature/protection states. Where an independent probe is used, record its location, pressure reference and temperature suitability.

What published comparisons can and cannot show

In a MyGolfMk7 comparison, one GTI with an IS38+ turbo, catted aftermarket downpipe and custom 93-octane tune was tested with stock versus aftermarket rear exhaust hardware. The author compared several third-gear acceleration runs and reported no statistically significant difference in acceleration time or estimated peak wheel power in the selected five-run sets. Session temperature and sample size limited the result; it does not prove all cat-backs give zero gain. The reported power was estimated from acceleration data, not a separate wheel-dyno measurement.

In a separate stock-calibration logging example, the author reviewed one GTI's logs with a particular catted aftermarket downpipe and reported lambda and manifold pressure tracking their respective requests in the observed runs. That result does not validate other downpipes, different software, long-term catalyst monitoring or emissions compliance. A steady-state bench-flow comparison is useful for comparing tested parts at the stated conditions, but does not reproduce pulsating hot exhaust or by itself predict installed power. Downpipe test methodology.

Fitment and diagnostic workflow

  1. Check intended fitment, turbo outlet, sensor bungs and wiring reach, catalyst/particle-filter configuration, joints, hangers, heat shielding and clearance for the exact vehicle. Use the exhaust manufacturer's installation instructions and the vehicle repair information.
  2. Investigate leaks and faults before changing calibration. Exhaust leaks, oxygen-sensor wiring, valve operation, restriction or incorrect hardware configuration can all affect sound or diagnosis. Preserve catalyst and oxygen-sensor monitoring; use current vehicle-specific procedures for any fault.
  3. For a meaningful comparison, record the same fuel, software, gear, rpm range, conditions and test method before and after the one change. Compare the same pressure location and absolute/gauge convention. Use controlled facilities and account for temperature, sample variation and instrumentation rather than claiming a general gain from one run.

Check local road-use, emissions, noise and type-approval requirements for the exact vehicle and replacement system. Supplier fitment or a catalyst in a pipe is not proof of approval in every market.

Related: exhaust-pressure modelling · bigger turbo tuning · turbocharger protection · exhaust flaps · oxygen sensors · catalyst protection. References reviewed 17 November 2026.