Purpose and scope
The manifold pressure sensor and the pressure-upstream-of-throttle (PUT) sensor describe different points in the air path. A higher-range sensor can be useful when the original sensor cannot measure the intended pressure, but its output must be interpreted correctly throughout the engine's operating range. The ECU uses pressure information in its air-path calculations and diagnostics. A pressure rating alone does not establish a replacement sensor's voltage-to-pressure relationship. Volkswagen's SSP 522 identifies G71 manifold pressure and G31 charge pressure sensors for its illustrated EA888 application; check the actual engine and wiring before identifying a sensor.
The calibration names below are examples from the community SC8S5031_C Simos 18.1 reference. Confirm software ID, definition, units, curve, axes, electrical interface and sensor data for the exact ECU and hardware. Other versions may differ. No addresses or universal replacement values are implied. Source: SC8S5031 pressure acquisition definitions.
Sensor conversion names
| Definition | Role in this reference |
|---|---|
ip_prs_im_mes | Manifold pressure conversion characteristic, hPa output against vp_prs_im_sens sensor voltage. Its voltage-axis reference is ldp_vp_prs_im_sens_mv_ip_prs. |
ip_prs_up_thr_mes | PUT pressure conversion characteristic, hPa output against vp_prs_up_thr_sens sensor voltage. Its voltage-axis reference is ldp_vp_prs_up_thr_mv_ip_prs_up. |
vp_prs_im_sens, vp_prs_up_thr_sens | Voltage measurements, not pressure targets or tuning maps. |
ip_amp_mes | Ambient-pressure conversion, separate from both MAP and PUT sensor conversions. Air pressure determination reference. |
The two sensor conversion curves each have two voltage-axis points in the cited reference. That is a description of this definition, not proof that any sensor's response is linear or compatible. An independently published 8V0906264L community XDF also labels MAP and PUT scaling; it is not a factory specification. Some generated descriptions conflict, so corroborate the map input, output, code and actual sensor behavior rather than relying on the label alone.
Absolute pressure, range and replacement
Pressure sensors generally report absolute pressure; a boost-gauge value is relative to ambient. Compare like units and reference pressures. For example, 3,000 mbar absolute at 1,000 mbar ambient corresponds to 2,000 mbar gauge; local ambient varies. A sensor advertised by its maximum bar rating may have a different useful minimum, output slope, offset, electrical connector or temperature element. Obtain the actual part's data and verify vacuum as well as high-pressure coverage; do not transfer a scaling recipe based solely on “4 bar”.
Drivability problems after a higher-range MAP change are an example of the risk. A community Simos 18 report describes drivability issues and faults following a higher-range MAP change and scaling work, with possible sensor and scaling causes discussed but no general solution established. It is an anecdote, not validation of a particular sensor or conversion.
Checks and logging
- Record the ECU software ID, original sensor part numbers, sensor locations and the replacement's transfer data. Confirm the supply, signal, ground and any shared temperature-sensor connections against the relevant documentation.
- With ignition on and engine off, after readings settle, compare manifold and upstream-throttle pressures with local ambient as a basic plausibility check. This single point cannot verify the high-pressure slope.
- Using a suitably rated controlled pressure source and an independent calibrated reference, compare the raw sensor output and ECU-converted pressure at multiple relevant points, including low and high pressures within the equipment's permitted range. Correct interpretation requires the actual sensor curve, its axis and ECU scaling to agree. Preserve sensor fault and plausibility diagnostics.
- On a healthy engine, log manifold and PUT pressures and their respective targets, ambient pressure and available sensor voltage while checking for implausible readings or faults. COBB distinguishes PUT Sensor (Raw), calculated upstream pressure and PUT setpoint in its MQB monitor definitions; channel availability and meaning depend on vehicle and tool. A setpoint is a request, not a measurement.
- Investigate leaks, wiring, sensor saturation and actual control behavior before changing boost requests or diagnostic limits. A sensor conversion, a pressure target and a protective limit are separate functions.
For ambient pressure, altitude and compressor pressure-ratio examples, see Simos 18 altitude and ambient pressure effects.
Related: air charge modelling, wastegate and boost control, bigger turbo tuning and turbocharger protection.
Sources and evidence
- Community SC8S5031 Simos 18.1 cross-reference: pressure acquisition — image-specific definitions; extracted metadata and prose can conflict.
- SimosDefinitions: 8V0906264L XDF — community calibration labels for a different image.
- Volkswagen SSP 522, EA888 2.0 TSI — hardware example, not universal fitment.
- COBB: Volkswagen and Audi MQB monitor list — product-specific monitor definitions.
- NefMoto: Simos18 MAP sensor discussion — community troubleshooting reports.