Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Torque, air and the transmission

Scope: These are EA888 Simos 18 examples, mainly 18.1. Exact ECU hardware, engine, transmission, software, calibration and patches determine whether a function or definition applies. Community labels are research leads: confirm the target A2L, axes, units, scaling, selectors and logs. Neither listed names nor file ranges are recommended settings.

The engine ECU coordinates requested torque, air charge and limits; the DSG receives torque information and may request a reduction. Torque is modelled and should be distinguished from dyno measurement. The EcuTek EA888 Mk7 tuning guide explains the EA888 fast and slow paths; the EcuTek DQ250 guide describes how its DQ250 example uses engine torque information in clutch and shift control.

Definition names to investigate

The bri3d a2l2xdf community definition list groups the following families; selectors, indexes and units must be checked against the exact ASW:

  • ip_maf_stk_sp_vvl_cam_h and ip_maf_stk_sp_vvl_cam_l — torque-related air-mass setpoint map families, with flap, lift and cam selections.
  • ip_tqi_ref_n_m_air_vvl_cam_h and ip_tqi_ref_n_m_air_vvl_cam_l — reference indicated-torque map families related to air charge, rpm and operating selections.
  • ip_tq_pow_max_at and ip_tq_pow_max_mt — maximum clutch-torque map families. Gearbox, power-class and software selectors require verification.
  • ip_fac_tq_req_driv_h_vs_dct and ip_fac_tq_req_driv_l_vs_dct — community labels for DCT high/low-speed driver request factors, not a substitute for checking the complete request path.

A Mk7 GTI discussion compares related air-to-torque and torque-to-air relationships, but other corrections and states mean they should not be treated as exact inverses in all conditions. Indicated, clutch/output, estimated and requested torque describe different points in the calculation.

Axes, selection and limits for a turbo upgrade

In the SC8S5031 torque-based air-setpoint reference, the ip_maf_stk_sp_vvl_cam_h/l family uses engine speed and indicated-torque request axes and returns air mass per stroke. The corresponding reference-torque family ip_tqi_ref_n_m_air_vvl_cam_h/l instead uses engine speed and cylinder air mass and returns indicated torque. Thus the second axis and output have different units and roles. Selection depends on the applicable intake flap, valve lift and cam conditions; community cross-mapped indexes can conflict, so confirm the actual selector.

The SC8S5031 torque-limitation cross-reference identifies ip_tqi_pow_max_bas as a full-load indicated-torque limitation. This is a different torque quantity from the clutch-torque families ip_tq_pow_max_at and ip_tq_pow_max_mt. Check the relevant selector and units rather than applying the same value to each family.

The SC8S5031 air-mass-limit reference describes ip_m_air_cyl_max_stnd_vvl as a standardised fresh-air limit by rpm and valve lift. m_air_cyl_max_cor_vvl and ratio_m_air_cyl_max are runtime values, not additional calibration tables. Ambient and intake-temperature corrections can affect the resulting limit. A flat displayed load may instead be a channel range, scaling or sampling issue, so verify the logger before blaming this map.

When inspecting a turbo setup, compare the current torque request, limited torque, requested and corrected cylinder air charge, selected operating state and pressure targets. A change to an air-setpoint family does not by itself ensure coherent reverse torque reporting, and changing a reference map does not directly establish measured output. The EcuTek EA888 guide discusses selected air-charge maps and logging for its documented applications.

DSG and logs

The DQ250 guide says ECM torque influences clutch-pressure control in that documented gearbox. Under-reporting to bypass a limit can make the information less representative of the actual load. Compare ECU and TCU identification, requested and limited torque, air-charge targets, actual/estimated values, gear, shift request, clutch behaviour and intervention status where supported.

A manual GTI case reported torque reduction after shifts despite normal dynamometer pulls; the suggested maps were not validated as the cause. It demonstrates why a steady pull does not cover every transient.

Detailed Simos 18 guides: torque model calibration · DSG torque coordination.

Related guides: bigger turbos · wastegate and boost control · fuel-system and MPI upgrades · ethanol and flex fuel · torque model and DSG · ignition and knock · launch control · rolling anti-lag.

References reviewed 17 November 2026. Forum accounts are reported observations, not independently verified fixes.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.