Scope. Exhaust pressure affects the turbine, gas exchange and diagnostic interpretation; the intake boost number alone cannot show it. This guide uses the community SC8S5031_C_OEM Simos 18.1 EGPR cross-reference for software examples, plus manufacturer information for specific EA888 vehicles. Verify engine, ECU ASW/CAL, exhaust arrangement, fitted sensors, active branch, axes, units and source of each logged value. Representable ranges are not calibration targets.
Locate the pressure before comparing it
Pressure upstream of the turbine describes the exhaust drive side; pressure downstream of the turbine and upstream of the catalyst describes a different location. Pressure before and after the catalyst can help assess catalyst restriction. A value described only as “exhaust pressure” or “backpressure” is incomplete without its measurement point and reference. Volkswagen SSP 522 describes an integrated exhaust manifold and a turbo bolted to it for its 2.0-litre 162/169 kW EA888 example; verify the actual exhaust and catalyst layout on the car.
For comparisons that require a physical pressure ratio, use absolute pressures at the two stated points, recorded together. For example, at an ambient pressure of 1.00 bar, 2.00 bar gauge corresponds to 3.00 bar absolute; dividing that by 1.50 bar absolute gives a ratio of 2.0. Gauge-pressure ratios are different and become misleading near zero. Always state whether a ratio compares turbine inlet with turbine outlet, exhaust with intake, or a current model value with a reference. Garrett explains gauge and absolute pressure.
Modelled pressure and calibration examples
These examples are from EGPR exhaust gas pressure. Their existence does not prove that a car has an exhaust-pressure sensor, or that the ECU's estimate remains accurate after a turbo or exhaust change.
ip_prs_ex_pcat_inc_1[3]is labelled a pressure increase from catalyst flow, output in hPa againstmfl_sum_catin kg/h and ambient pressureampin hPa. Check which exhaust-system index and branch are selected; this is a model term, not a measured catalyst pressure drop or a universal replacement-exhaust calibration.ip_crlc_prs_ex_pcat_inc[1]is a low-pass filtering coefficient for pressure before the catalyst with engine-speednin rpm as its axis. It changes model dynamics, not the restriction itself.ip_pq_tur_1_ref[1]is a turbine pressure quotient at reference conditions against engine speed and an air-mass-per-stroke axis; the latter hasNO_INPUT_QUANTITYmetadata. Verify the actual input and ratio direction.ip_pq_tur_l_bpa_closeandip_pq_tur_l_bpa_openare labelled low-load turbine-quotient maps for closed and open wastegate. Their axes are labelled kg/h and hPa but haveNO_INPUT_QUANTITYmetadata; the open map's adjacent FR table caption says closed. Confirm selection, inputs and implementation before use.ip_ratio_prs_ex_wg_ofs[3]is an offset for the exhaust-pressure ratio depending on operating point and wastegate position. The source identifies engine speed, air-mass and position-related data; verify index selection and interpolation, especially the dummy axis map.ip_fac_teg_dyn_prs_pcatis a dynamic temperature-correction factor with an unbound axis in the extraction.
prs_ex_pcat_up_dyn is a runtime model-path value labelled absolute pre-catalyst pressure on reference conditions. ratio_prs_ex is a current-to-reference exhaust-pressure ratio; its documented selector lc_ratio_prs_ex_pcat chooses pre-catalyst versus pre-turbine ratio in this reference. It is not automatically a measured turbine-inlet-to-outlet ratio or exhaust-to-intake ratio. Confirm selector, computation and logger support. A variable labelled MEASUREMENT in a definition can still be calculated.
Exhaust-system diagnostic is a different function
The SC8S5031 EGPR exhaust-system diagnosis reference lists ip_map_int_ex_sys_ref as a reference manifold-pressure integral in hPa·s indexed by ambient pressure and catalyst temperature, and ip_fac_map_int_ex_sys_tia as its intake-air-temperature correction. map_int_ex_sys, state_map_int_ex_sys and lv_cdn_diag_ex_sys are runtime integral, test-state and diagnostic-condition fields. The extracted selector lc_put_mes_act_ex_sys_int can substitute PUT for a MAP-related calculation in that strategy. This is an indirect, condition-dependent diagnostic, not a pressure gauge or a universal P-code definition; do not infer a healthy catalyst from a test that did not run.
Practical measurement and tuning checks
- Record ECU and turbo identification, exhaust and catalyst configuration, ambient pressure, test conditions and fault/freeze-frame information. Confirm where any independent pressure probes are installed and whether values are absolute or gauge.
- Compare turbine-inlet and turbine-outlet pressure at matched engine speed, load, temperature and wastegate state where suitable instruments are fitted. Exhaust pulses, probe location, sensor response, heat protection and filtering affect readings. Do not mount an ordinary low-temperature pressure sensor directly in hot exhaust without a suitable engineered installation.
- Log available manifold and upstream-throttle targets and actuals, engine speed, actuator request and feedback, air charge, lambda and temperature-related protection. A logged model pressure is useful context but must be validated independently before treating it as a measured limit.
- For suspected restriction, distinguish pressure before and after the catalyst and investigate intake leaks, actuator and other faults as well. An Audi technical-service training example lists pre/post-catalyst pressure testing among its P0299 underboost checks and also lists several other causes. Follow the current vehicle-specific procedure; the document's general idle example is not a universal full-load specification.
- Compare matched before/after logs for a hardware change, including operating and ambient conditions. Diagnose physical mismatches before recalibrating models. Retain catalyst and turbo protection and avoid treating a changed estimate as evidence that real pressure or temperature has improved.
Related: bigger turbo tuning · wastegate and boost control · exhaust gas temperature modelling · catalyst protection · turbocharger protection. References reviewed 17 November 2026.
For EA888 exhaust hardware and source-qualified downpipe and cat-back comparisons, see Simos 18 exhaust and downpipe upgrades.