Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Fixed blend or sensed flex fuel?

Scope: These are EA888 Simos 18 examples, mainly 18.1. Exact ECU hardware, engine, transmission, software, calibration and patches determine whether a function or definition applies. Community labels are research leads: confirm the target A2L, axes, units, scaling, selectors and logs. Neither listed names nor file ranges are recommended settings.

A fixed blend calibration assumes a specified ethanol content. A sensor-based system needs working measurement, wiring and software to use the value; a map-switch position labelled E85 does not itself measure the tank. Available strategies also differ in what they adjust beyond fuel quantity. The Simos 18 flex-fuel thread discusses the difference between fuel adaptation and an ethanol-dependent ignition patch.

Examples of factory-related identifiers

The bri3d a2l2xdf community definition list and Simos Wiki fuel overview list lc_fac_afu_ratio_conf (sensor configuration), lc_fac_afu_ratio_man_act (manual alternative-fuel selection), and c_fac_afu_ratio_man (manual value). Confirm exact meaning and polarity against the matching ASW and the installed patch; values from a different tool or implementation are not a substitute for validation. Check displayed ethanol content against a known fuel sample and diagnose sensor failure and fallback as documented for the actual system.

EcuTek RaceROM example

The EcuTek EA888 flex-fuel guide documents fixed, CAN and sensor inputs for its EA888 implementation and labels FlexFuel Fuel Quantity Multiplier, FlexFuel Cranking Multiplier, FlexFuel Boost Target Max, FlexFuel Lambda Base Set Point, FlexFuel MPI DI split Normal/Warmup and FlexFuel start of Injection HPDI. These are EcuTek feature labels, not universally present OEM identifiers. The maps and blend curves are enabled and selected within that implementation.

Its development example reports low-pressure fuel flow running short at a particular blend on one hybrid-turbo car. That observation is not a safe ethanol limit for any other car. Validate low-side and high-pressure supply, injection timing, lambda and corrections across the intended blend range, including starting and warmup. Higher ethanol content does not by itself prove that knock is absent or that a fuel system has headroom.

The EcuTek EA888 flex-fuel guide describes ethanol blending of its per-mode flex ignition maps with baseline ignition, and product-specific knock-threshold features. These are RaceROM controls, not universal OEM map names; changing a detection threshold affects detection rather than merely the displayed correction. See ignition timing and knock detection and control.

Sensor signal, held values and product-specific diagnostics

The COBB MQB flex-fuel guide describes Threshold to Update MFF Value, Flex Fuel Ethanol Hold Content Boost and Flex Fuel Ethanol Hold Content RPM. In that implementation the last used ethanol content can be held above the configured boost or RPM condition and updated again after the condition clears; the update threshold also affects when changes are adopted. These are COBB feature labels, not universal OEM map names. A stable used value while the raw signal changes can reflect this strategy rather than a working sensor. COBB's MQB monitor list distinguishes Ethanol Content Read from Sensor from Ethanol Content Used.

COBB notes its particular returnless-system sensor arrangement may read a blend that differs temporarily from fuel farther along the system while recently added fuel mixes. Record sensor location, blend history and time, compare a representative sample where practicable, and follow the installed system's diagnosis and fault-response procedures. Hold and smoothing features do not repair faulty wiring, contaminated fuel or an unreliable sensor, and a calculated expected blend is not an independent measurement of fuel composition at the injectors.

The COBB MQB Mk7/7.5 flex-fuel DTC list identifies C0B13 as an ethanol content limit reached or exceeded and C0B16 as fuel temperature out of range. It also lists C0B12 for implausible sensor frequency and C0B14 for a lambda-controller-based ethanol-sensor plausibility diagnosis. These are product-specific diagnostics with multiple possible causes; neither a single code nor an enabled flag proves a failed sensor. Check diagnostic availability and exact calibration before applying their descriptions elsewhere.

Owner-reported example: In a Mk7 Golf R flex-fuel discussion, the owner reported unstable sensor readings and C0B13/C0B16 after an EQT 93/E85 flex-fuel flash. Replacing the sensor and moving a ground had not resolved the reported behaviour at the time of the post. A connector or harness fault was suspected, but the thread did not establish a root cause or confirmed repair, and the exact ECU software was not identified. This case supports checking the whole signal path and actual fuel rather than attributing fluctuating content to a sensor alone.

For frequency and temperature conversion, delayed ethanol values, electrical and plausibility diagnostics, see Simos 18 ethanol sensor signal and flex-fuel diagnosis.

Alternative-fuel cold start and warm-up paths

In the SC8S5031 FMSP post-start cross-reference, ip_fac_afu_ratio_cast is an interpolation function against alternative-fuel ratio fac_afu_ratio; its narrative describes blending gasoline and alternative-fuel post-start paths in a configured system. This is separate from ip_mff_fac_afu's basic running fuel-mass calculation and from an aftermarket cranking multiplier. Confirm the selected ratio source, function configuration and complete equation in the matched software.

  • ip_add_mff_cast_ini_afu and ip_add_mff_cast_ini_at_afu describe initial alternative-fuel post-start enrichment factors, the second labelled for automatic transmission. Their axes are intake-manifold air temperature tia_im and coolant temperature tco, in °C. ip_add_mff_cast_cha_afu is a charger-related factor against n_32 rpm and manifold pressure prs_im hPa.
  • ip_add_mff_deac_cast_afu is a deactivation factor versus corrected after-start cycle count cyc_cast_cor and coolant temperature, not a direct time-in-seconds map. ip_fac_fq_cast separately weights fuel-quality adaptation against fac_fq_st_ad and tco; it is not an ethanol-content sensor reading. FMSP post-start reference.
  • ip_fac_afu_ratio_wup is a separate interpolation curve for the warm-up correction versus fac_afu_ratio. ip_fac_mff_tco_wup_afu and ip_fac_mff_tco_maf_int_ast_wup_afu describe alternative-fuel warm-up deactivation factors, the former using coolant and start-related coolant temperatures, and the latter an integrated-air input in grams and start-related coolant temperature. The source's air-input description and signal label differ; confirm the actual input against the matched file. FMSP warm-up reference.

The ALFU default-start reference describes an optional strategy for a start after an incorrectly estimated alternative-fuel ratio, including an example where refuelling and shutdown precede new fuel reaching the engine. It lists id_fac_dft_st as a factor for the default-start ratio, with a cycle-counter-labelled axis marked NO_INPUT_QUANTITY and a coolant-temperature axis; fac_afu_ratio_dft_st and lv_fac_afu_ratio_dft_st_req are runtime values, not editable maps. Availability, enabling conditions, stored blend and logger access are application-specific; this is not proof that a particular retrofit uses the strategy or measures fuel composition. Check the source labels and code before using any map.

For comparison, EcuTek's EA888 RaceROM documentation describes additional cranking fuel for its implementation, with an RPM threshold and decay controlling the cranking correction. These product-specific controls do not establish the behaviour of an unpatched ECU. Verify actual blend, pressure supply, injector calibration and cold-start sensor readiness before changing fuelling.

Owner report: A 2015 Golf R owner reported a recently installed flex-fuel tune, upgraded HPFP and sensor, approximately 58% ethanol and mild extended cranking on a cold start. Ambient temperature was reported as 85 °F; no root-cause testing, ECU software identification or confirmed repair was supplied. This is an observation on one car, not evidence that the blend caused the crank duration or a general temperature threshold.

Logging

Record actual or fixed ethanol source and content, map slot, lambda target and actual, fuel trims and loop status, low-side and rail pressure, DI/MPI timing and mode where available, ignition, knock correction, intake temperature and any relevant fault. Distinguish a calculated/manual content from a live sensor signal.

Fuel blend calculation and starting

The SC8S5031 basic injection mass reference lists ip_mff_fac_afu as an alternative-fuel stoichiometric fuel-mass factor versus an alternative-fuel ratio input. It concerns the basic fuel calculation; it does not establish ethanol-dependent boost or ignition blending. Confirm the curve, scaling, ratio source and selected mode against the matching software. The alternative-fuel determination reference provides context for the factory-related identifiers above.

EcuTek additionally documents FlexFuel Cranking RPM threshold and FlexFuel Cranking Multiplier decay rate, alongside its fuel quantity, cranking and normal/warm-up MPI split controls. These are RaceROM feature names, and their availability and operation depend on the installed implementation. Assess cold start, cranking, warm-up, blend changes and DI/MPI transitions along with steady-state lambda and fuel pressure. EcuTek EA888 flex-fuel guide.

Detailed fuelling guides: MPI combustion modes and fuel split · MPI injector calibration · direct injection and fuel pressure.

Ethanol content and petrol octane are different properties; for octane requirements and related knock adaptation see Simos 18 fuel octane and knock adaptation.

Related guides: bigger turbos · wastegate and boost control · fuel-system and MPI upgrades · ethanol and flex fuel · torque model and DSG · ignition and knock · launch control · rolling anti-lag.

For temperature-dependent starting and fuelling, see cold start tuning.

For low-side pressure, pump duty and upgraded pump control, see Simos 18 low pressure fuel pump control and upgrades.

References reviewed 17 November 2026. Forum accounts are reported observations, not independently verified fixes.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.