Scope: The hardware example is Volkswagen's CHHB/CHHA EA888 2.0 TSI with Simos 18.1. Calibration identifiers and signal descriptions are from the community SC8S5031_C_OEM reference, not guaranteed definitions for other Simos 18 software. Verify ECU ID, hardware, matching definitions, selectors, axes, units and actual operating behaviour. Some extracted functional descriptions are inconsistent; identify the map from multiple pieces of evidence rather than its label alone. Volkswagen SSP 522; SC8S5031 CHRG recirculation setpoint reference.
Recirculation valve and wastegate
The turbocharger recirculation or diverter valve provides a bypass path for compressor-side air during conditions including throttle lift. Volkswagen identifies N249 in the compressor housing on the illustrated EA888 turbocharger, and shows recirculated air during overrun. V465 is a different actuator which moves the exhaust-side wastegate. Do not mistake an N249 request for a wastegate position or assume all turbocharger conversions use the same routing and valve. SSP 522, air supply and forced induction.
Recirculation commands are coordinated with pressure and transients. The example software includes surge-related requests and a post-shift window: it is not simply a sound effect. Removing, forcing closed or slowing the valve can alter compressor operation and transient response; diagnose the actual cause of a noise or boost problem before changing control logic. The cited definitions establish a protection-related path, not a universal threshold or a guarantee against compressor damage.
Example control maps and values
These entries are from the CHRG setpoint reference; calibration values are image- and hardware-specific:
ip_t_rcl_close_dlyis described as the minimum opening time of the recirculation actuator, with manifold-pressure setpointprs_im_spin hPa and engine speednin rpm as axes and milliseconds as the output. The source's copied functional-description text conflicts with this heading, so verify the matched definition and active logic.ip_t_rcl_close_dly_flgives a minimum high-load opening time in milliseconds against engine speed.ip_t_rcl_open_act_flis the time window, also in milliseconds against speed, in which an opening can be triggered after a high-load gear shift. The documented trigger involves detected compressor surge; this is not an unconditional gearshift opening command.ip_pv_grd_rcl_open_thdis a pedal-gradient opening threshold in percent per second against engine speed.ip_fac_tq_req_grd_rcl_close_setandip_fac_tq_req_grd_rcl_close_rstare pedal-factor gradient thresholds for setting and resetting a closing request, against engine speed and gear. Cross-check selector, sign and implementation; some generated prose appears shifted between fields.c_pq_put_amp_min_rcl_openis the minimum upstream-throttle to ambient-pressure ratio for an opening condition, andc_pq_cha_min_rcl_open_fl_surgea minimum compressor pressure ratio for high-load opening. These are dimensionless conditions, not boost setpoints.c_map_sp_hys_rcl_openis a manifold-pressure-setpoint hysteresis in hPa.c_t_per_open_rclandc_t_per_close_rclare periodic opening and closing times for a diagnostic path, not the normal post-shift opening maps. A diagnosis can deliberately command the valve under specified conditions.
Requested, measured and modelled positions
In the CHRA position reference, psn_rcl_sp is the position setpoint. psn_rcl is a selected position which can be measured, modelled, or overridden depending on the active conditions. psn_rcl_mes is described as the measured signal and psn_rcl_mdl as modelled; lv_ena_psn_rcl indicates position-sensor enable. The existence of a measured channel in an engineering definition does not prove the target vehicle has that sensor. The described psn_rcl convention is 0% closed and approximately 100% open, but verify the tool's presentation and configuration.
lv_rcl_open_req is an opening request and lv_rcl_open_req_surge is a surge-related opening request in the cited CHRG reference. They are runtime signals, not editable maps and not proof of physical movement. lv_rcl_diag_open_act is associated with a diagnostic opening: an unexpected request in a log should be interpreted alongside fault and diagnostic state.
Fault diagnosis and modifications
- Record exact engine and ECU software, turbo/valve part and routing, fault codes, freeze frame, and when the symptom occurs. Check the appropriate current workshop repair procedure.
- Compare throttle and pedal positions, manifold and upstream-throttle pressure and targets, ambient pressure, turbo actuator request and available recirculation request or feedback at appropriate sampling rates. A target is not a measured pressure; identify gauge versus absolute units and whether valve position is modelled.
- Inspect the valve, seals, air-path connections, wiring and the operation of the relevant actuator using the manufacturer's approved diagnostic procedure. A pressure-control fault or poor boost response can have several causes, including leaks, pressure sensors and wastegate control; it does not by itself identify N249.
- The SC8S5031 diagnostic reference contains pressure-model terms such as
ip_put_mdl_rcl_close_ofs_1andip_put_mdl_rcl_open_ofs_1. These are diagnosis-model offsets, not normal pressure targets; preserve diagnostic and protection functions when investigating a change. - For a larger turbo or replacement valve, confirm physical fit, electrical control, seal and recirculation route for that specific kit; compare logs before and after the hardware change. Integrated Engineering's GT2260S MQB kit description, for example, lists a supplied diverter valve and dedicated tuning. This documents that kit only, not a universal upgrade or required calibration recipe.
Related: wastegate and boost control · turbocharger protection · bigger turbo tuning · MAP and boost pressure sensors.
Sources
- Volkswagen SSP 522: EA888 2.0 TSI design and function, air supply and turbocharger sections; manufacturer hardware example.
- SC8S5031 community CHRG recirculation setpoint definitions; examples of maps, conditions and signals.
- SC8S5031 CHRA recirculation actuator position; position source and enable distinctions.
- SC8S5031 recirculation valve diagnosis and turbocharger plausibility diagnosis; image-specific diagnostic references.
- Integrated Engineering GT2260S MQB product information; kit-specific equipment description.