Removed text is struck through; added text is highlighted.
Hard starting, stalling or loss of power can be caused by a fuel pump, but also by a restricted filter, poor electrical supply, a pressure-control fault or excessive injector leakage. Test the fuel system as a whole before replacing a pump.
Simplified common-rail fuel path: the supply, high-pressure and return circuits have different jobs. Layouts vary. Original Tuning Wiki illustration, also used in common-rail diesel fuel systems.
Fuel delivery faults can alter mixture feedback. See common oxygen sensor faults.
Coolant-temperature faults can resemble fuel-supply starting complaints. See common coolant temperature sensor faults.
A missing crankshaft signal can also cause no-start or stalling. See common crankshaft position sensor faults. See also Camshaft position sensor faults. See also Throttle position sensor faults. See also Accelerator pedal position sensor faults. See also Knock sensor faults. See also Intake air temperature sensor faults. See also Exhaust gas temperature sensor faults. See also DPF differential pressure sensor faults. See also NOx sensor faults. See also AdBlue and SCR system faults.A missing crankshaft signal can also cause no-start or stalling. See common crankshaft position sensor faults. See also Camshaft position sensor faults. See also Throttle position sensor faults.
Quick symptom guide
SymptomStart by checking
No start or long crankBattery and cranking speed, fuel level and supply, fault codes, pressure demand and actual pressure.
Power falls under loadFuel pressure and delivery under the fault conditions; blocked filter, supply, pump control, rail regulation and sensors are possibilities.
Stalls intermittently or when hotElectrical supply and ground, pump control, connectors and fuel delivery; confirm the fault before replacing parts.
Low rail pressureLow-pressure feed first, then high-pressure regulation, injector return where applicable and sensor plausibility.
Metal particles in fuel componentsStop running the system and follow the vehicle-specific contamination diagnosis; the pump and other parts may be affected.
Know which pump you are testing
A low-pressure pump supplies fuel from the tank or through a feed circuit. A petrol port-injection system may use it to supply the injector rail directly. Many diesel common-rail and petrol direct-injection systems also have a high-pressure pump. Arrangements differ: some diesel systems draw fuel rather than using a separate electric in-tank feed pump.
A pump operating during an actuator test proves that it responds; it does not prove sufficient pressure and flow under demand. Follow the test plan for the engine and pump arrangement. HELLA's fuel-system guidance explains why a restricted supply can become apparent only at higher demand.
Safety before opening the fuel system
High-pressure fuel can penetrate skin and cause serious injury. Diesel common-rail and petrol direct-injection circuits may remain pressurised after the engine stops. Do not loosen a high-pressure connection while running or search for a leak by hand. Follow the manufacturer's depressurisation and isolation procedure, use correctly rated equipment, and seek immediate emergency medical attention for a suspected injection injury.
Fuel and vapour can ignite. Work in an appropriate ventilated area, control ignition sources, collect fuel safely and follow the manufacturer's electrical and environmental procedures.
Diagnostic sequence
Record the complaint. Note starting behaviour, temperature, fuel level, load, recent work and fuel-filter history. Save all fault codes and freeze-frame data before clearing them.
Identify the system. Establish the engine, fuel and pump types, low- and high-pressure circuits, control method and correct service data.
Inspect safely. With the system isolated as specified, inspect wiring, connectors, lines, filter and housing for damage, leaks or evidence of contamination. Check the correct fuel and filter are fitted.
Review live data. Compare requested and actual fuel pressure during the complaint, including cranking or load when appropriate. Check that the sensor reading is plausible and the reported units are understood.
Check the low-pressure supply. Measure pressure and delivery using the approved equipment, test points and conditions. Inspect restrictions and air ingress where relevant. Pressure at idle alone does not prove adequate flow under demand.
Check electrical control. On electric pumps, test command, supply and earth under operating conditions. A poor connection or voltage drop can make a sound pump underperform.
Investigate the high-pressure side. Once feed is confirmed, follow the specified checks for the pressure sensor, metering or regulation, pump drive and injector leakage. Do not infer a failed pump from a low-pressure code alone.
Repair the cause and verify. Follow cleaning, replacement, priming and adaptation procedures for the system. Check for leaks by the approved method and repeat the original test.
Use the manufacturer's pressure and flow limits. HELLA's high-pressure pump guide illustrates checking low-pressure supply before assessing the high-pressure circuit. Delphi's voltage-drop guidance explains how a poor electrical connection can imitate a weak pump.
Fuel pressure, flow and control
Illustrative test points in a common-rail system. Test points and limits vary; use the vehicle manufacturer's procedure. Original Tuning Wiki illustration from common-rail fuel system tests.Illustrative test points in a common-rail system. The figures and test conditions in the illustration are examples for the original guide, not universal limits; use the vehicle manufacturer's procedure. Original Tuning Wiki illustration from common-rail fuel system tests.
Pressure and flow answer different questions. A system may reach its target at idle yet fail to deliver enough fuel at higher demand. Compare measurements under the vehicle manufacturer's specified conditions and investigate the filter, pipes, tank pickup and electrical supply before condemning the pump.
On a common-rail engine, low actual pressure can arise from insufficient feed, a regulation or sensor fault, excessive injector return, a mechanical drive issue or pump wear. A scan-tool reading is valuable but is still a sensor signal; use the vehicle's approved independent check where required. See common-rail fuel system tests.
For checking whether a rail-pressure reading is accurate, see common fuel pressure sensor faults.
Bosch CP4: roller and cam failures
The Bosch CP4 is a family of diesel high-pressure pumps. A cam drives a plunger through a roller and roller shoe or tappet assembly. Designs and vehicle plumbing vary, so identify the installed pump and engine before applying any repair procedure.
Diesel World's CP4.2 article contains photographs of the roller tappet, cam and an example of damaged roller and cam. The photographs are of one dismantled pump, not proof that a particular vehicle has the same damage. The publication's interpretation of causes is not a substitute for an examination of the affected pump.
What can fail?
In a 2024 response to the US safety regulator, Bosch described several possible damage mechanisms: loss of the lubricating film between roller and shoe, deposits that make a roller sticky, and water-related corrosion or fatigue. Bosch identified fuel properties, high fuel temperature, air, particles and water outside specified limits among possible influencing factors. These are manufacturer-reported mechanisms; the cause of an individual failure must be established from the vehicle and component evidence.
If the roller cannot roll correctly, abnormal sliding and wear can damage the roller, shoe or cam. Progressive damage can generate metallic particles that travel into the fuel system. Do not assume every CP4 fault has the same cause or that a particular bearing has failed merely because rail pressure is low.
Recognising and confirming the problem
Possible complaints include hard starting, a pressure fault, rough running, loss of power or sudden stalling. These are not unique to CP4 damage.Metallic debris in a fuel component is a significant finding but does not by itself identify its origin or prove the entire system is contaminated. Follow the manufacturer’s specified inspection points and preserve samples and findings.Absence of visible debris at one inspection point does not rule out internal wear or contamination elsewhere.Do not dismantle a pressurised pump or remove metering components as a generic shortcut. Use the applicable service procedure and a qualified diesel specialist where needed.
NHTSA's investigation closure for selected 2019–2020 6.7-litre Ram trucks describes a recall involving internal CP4 failure, debris and possible loss of motive power. That finding is scoped to the vehicles and market in the document; it is not a claim that every CP4 installation is recalled. Check the vehicle identification number with the manufacturer or relevant national recall service.
Contamination and repair
If internal pump damage or metallic contamination is confirmed, avoid further unnecessary cranking or running and follow the vehicle manufacturer's contamination procedure. Depending on the system and findings, the assessment can include the pump, metering valve, rail, injectors, high- and low-pressure lines, filter housing, tank, return circuit and feed pump. The prescribed action may be inspection, cleaning or replacement; it is vehicle- and component-specific. A new pump fitted into a contaminated system can be damaged again.
Retain diagnostic readings, photographs, debris samples and repair records. Use the specified fuel and filter and the manufacturer's priming procedure after service. No additive or conversion guarantees prevention; assess modifications against the vehicle maker's requirements and applicable approvals.
Poor power can also result from air metering or intake faults. See common MAF sensor faults.
An intake pressure sensor fault can also cause poor performance. See common MAP sensor faults.
Distinguish injector, DPF, EGR and turbo faults
Fuel starvation and air-system faults can both cause loss of power. Injector faults can also affect rail pressure or combustion, and poor combustion may contribute to soot loading. A DPF warning, EGR fault or low boost reading needs its own evidence; none alone proves a fuel-pump fault.
Common injector faults: cylinder checks, approved return-flow tests and coding.Common DPF faults: pressure sensing, soot and regeneration.Common EGR faults: valve, controls and flow.Turbo diagnostics: charge pressure and boost-control investigation.
After repair
Fit the correct components and new seals or pipes where specified. Prime the system and carry out adaptations only as directed. Check for leaks, clear codes when appropriate and compare pressure readings with the original fault conditions. Confirm the starting and driving complaint is resolved and investigate any returning fault.
For more system detail see fuel pump faults and common-rail supply pumps.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 9: Common fuel pump faults: symptoms, checks and CP4 failures
Hard starting, stalling or loss of power can be caused by a fuel pump, but also by a restricted filter, poor electrical supply, a pressure-control fault or excessive injector leakage. Test the fuel system as a whole before replacing a pump.
Simplified common-rail fuel path: the supply, high-pressure and return circuits have different jobs. Layouts vary. Original Tuning Wiki illustration, also used in common-rail diesel fuel systems.
Battery and cranking speed, fuel level and supply, fault codes, pressure demand and actual pressure.
Power falls under load
Fuel pressure and delivery under the fault conditions; blocked filter, supply, pump control, rail regulation and sensors are possibilities.
Stalls intermittently or when hot
Electrical supply and ground, pump control, connectors and fuel delivery; confirm the fault before replacing parts.
Low rail pressure
Low-pressure feed first, then high-pressure regulation, injector return where applicable and sensor plausibility.
Metal particles in fuel components
Stop running the system and follow the vehicle-specific contamination diagnosis; the pump and other parts may be affected.
Know which pump you are testing
A low-pressure pump supplies fuel from the tank or through a feed circuit. A petrol port-injection system may use it to supply the injector rail directly. Many diesel common-rail and petrol direct-injection systems also have a high-pressure pump. Arrangements differ: some diesel systems draw fuel rather than using a separate electric in-tank feed pump.
A pump operating during an actuator test proves that it responds; it does not prove sufficient pressure and flow under demand. Follow the test plan for the engine and pump arrangement. HELLA's fuel-system guidance explains why a restricted supply can become apparent only at higher demand.
Safety before opening the fuel system
High-pressure fuel can penetrate skin and cause serious injury. Diesel common-rail and petrol direct-injection circuits may remain pressurised after the engine stops. Do not loosen a high-pressure connection while running or search for a leak by hand. Follow the manufacturer's depressurisation and isolation procedure, use correctly rated equipment, and seek immediate emergency medical attention for a suspected injection injury.
Fuel and vapour can ignite. Work in an appropriate ventilated area, control ignition sources, collect fuel safely and follow the manufacturer's electrical and environmental procedures.
Diagnostic sequence
Record the complaint. Note starting behaviour, temperature, fuel level, load, recent work and fuel-filter history. Save all fault codes and freeze-frame data before clearing them.
Identify the system. Establish the engine, fuel and pump types, low- and high-pressure circuits, control method and correct service data.
Inspect safely. With the system isolated as specified, inspect wiring, connectors, lines, filter and housing for damage, leaks or evidence of contamination. Check the correct fuel and filter are fitted.
Review live data. Compare requested and actual fuel pressure during the complaint, including cranking or load when appropriate. Check that the sensor reading is plausible and the reported units are understood.
Check the low-pressure supply. Measure pressure and delivery using the approved equipment, test points and conditions. Inspect restrictions and air ingress where relevant. Pressure at idle alone does not prove adequate flow under demand.
Check electrical control. On electric pumps, test command, supply and earth under operating conditions. A poor connection or voltage drop can make a sound pump underperform.
Investigate the high-pressure side. Once feed is confirmed, follow the specified checks for the pressure sensor, metering or regulation, pump drive and injector leakage. Do not infer a failed pump from a low-pressure code alone.
Repair the cause and verify. Follow cleaning, replacement, priming and adaptation procedures for the system. Check for leaks by the approved method and repeat the original test.
Use the manufacturer's pressure and flow limits. HELLA's high-pressure pump guide illustrates checking low-pressure supply before assessing the high-pressure circuit. Delphi's voltage-drop guidance explains how a poor electrical connection can imitate a weak pump.
Fuel pressure, flow and control
Illustrative test points in a common-rail system. The figures and test conditions in the illustration are examples for the original guide, not universal limits; use the vehicle manufacturer's procedure. Original Tuning Wiki illustration from common-rail fuel system tests.
Pressure and flow answer different questions. A system may reach its target at idle yet fail to deliver enough fuel at higher demand. Compare measurements under the vehicle manufacturer's specified conditions and investigate the filter, pipes, tank pickup and electrical supply before condemning the pump.
On a common-rail engine, low actual pressure can arise from insufficient feed, a regulation or sensor fault, excessive injector return, a mechanical drive issue or pump wear. A scan-tool reading is valuable but is still a sensor signal; use the vehicle's approved independent check where required. See common-rail fuel system tests.
The Bosch CP4 is a family of diesel high-pressure pumps. A cam drives a plunger through a roller and roller shoe or tappet assembly. Designs and vehicle plumbing vary, so identify the installed pump and engine before applying any repair procedure.
In a 2024 response to the US safety regulator, Bosch described several possible damage mechanisms: loss of the lubricating film between roller and shoe, deposits that make a roller sticky, and water-related corrosion or fatigue. Bosch identified fuel properties, high fuel temperature, air, particles and water outside specified limits among possible influencing factors. These are manufacturer-reported mechanisms; the cause of an individual failure must be established from the vehicle and component evidence.
If the roller cannot roll correctly, abnormal sliding and wear can damage the roller, shoe or cam. Progressive damage can generate metallic particles that travel into the fuel system. Do not assume every CP4 fault has the same cause or that a particular bearing has failed merely because rail pressure is low.
Recognising and confirming the problem
Possible complaints include hard starting, a pressure fault, rough running, loss of power or sudden stalling. These are not unique to CP4 damage.
Metallic debris in a fuel component is a significant finding but does not by itself identify its origin or prove the entire system is contaminated. Follow the manufacturer’s specified inspection points and preserve samples and findings.
Absence of visible debris at one inspection point does not rule out internal wear or contamination elsewhere.
Do not dismantle a pressurised pump or remove metering components as a generic shortcut. Use the applicable service procedure and a qualified diesel specialist where needed.
NHTSA's investigation closure for selected 2019–2020 6.7-litre Ram trucks describes a recall involving internal CP4 failure, debris and possible loss of motive power. That finding is scoped to the vehicles and market in the document; it is not a claim that every CP4 installation is recalled. Check the vehicle identification number with the manufacturer or relevant national recall service.
Contamination and repair
If internal pump damage or metallic contamination is confirmed, avoid further unnecessary cranking or running and follow the vehicle manufacturer's contamination procedure. Depending on the system and findings, the assessment can include the pump, metering valve, rail, injectors, high- and low-pressure lines, filter housing, tank, return circuit and feed pump. The prescribed action may be inspection, cleaning or replacement; it is vehicle- and component-specific. A new pump fitted into a contaminated system can be damaged again.
Retain diagnostic readings, photographs, debris samples and repair records. Use the specified fuel and filter and the manufacturer's priming procedure after service. No additive or conversion guarantees prevention; assess modifications against the vehicle maker's requirements and applicable approvals.
Fuel starvation and air-system faults can both cause loss of power. Injector faults can also affect rail pressure or combustion, and poor combustion may contribute to soot loading. A DPF warning, EGR fault or low boost reading needs its own evidence; none alone proves a fuel-pump fault.
Fit the correct components and new seals or pipes where specified. Prime the system and carry out adaptations only as directed. Check for leaks, clear codes when appropriate and compare pressure readings with the original fault conditions. Confirm the starting and driving complaint is resolved and investigate any returning fault.
Revision 20: Common fuel pump faults: symptoms, checks and CP4 failures
Hard starting, stalling or loss of power can be caused by a fuel pump, but also by a restricted filter, poor electrical supply, a pressure-control fault or excessive injector leakage. Test the fuel system as a whole before replacing a pump.
Simplified common-rail fuel path: the supply, high-pressure and return circuits have different jobs. Layouts vary. Original Tuning Wiki illustration, also used in common-rail diesel fuel systems.
Battery and cranking speed, fuel level and supply, fault codes, pressure demand and actual pressure.
Power falls under load
Fuel pressure and delivery under the fault conditions; blocked filter, supply, pump control, rail regulation and sensors are possibilities.
Stalls intermittently or when hot
Electrical supply and ground, pump control, connectors and fuel delivery; confirm the fault before replacing parts.
Low rail pressure
Low-pressure feed first, then high-pressure regulation, injector return where applicable and sensor plausibility.
Metal particles in fuel components
Stop running the system and follow the vehicle-specific contamination diagnosis; the pump and other parts may be affected.
Know which pump you are testing
A low-pressure pump supplies fuel from the tank or through a feed circuit. A petrol port-injection system may use it to supply the injector rail directly. Many diesel common-rail and petrol direct-injection systems also have a high-pressure pump. Arrangements differ: some diesel systems draw fuel rather than using a separate electric in-tank feed pump.
A pump operating during an actuator test proves that it responds; it does not prove sufficient pressure and flow under demand. Follow the test plan for the engine and pump arrangement. HELLA's fuel-system guidance explains why a restricted supply can become apparent only at higher demand.
Safety before opening the fuel system
High-pressure fuel can penetrate skin and cause serious injury. Diesel common-rail and petrol direct-injection circuits may remain pressurised after the engine stops. Do not loosen a high-pressure connection while running or search for a leak by hand. Follow the manufacturer's depressurisation and isolation procedure, use correctly rated equipment, and seek immediate emergency medical attention for a suspected injection injury.
Fuel and vapour can ignite. Work in an appropriate ventilated area, control ignition sources, collect fuel safely and follow the manufacturer's electrical and environmental procedures.
Diagnostic sequence
Record the complaint. Note starting behaviour, temperature, fuel level, load, recent work and fuel-filter history. Save all fault codes and freeze-frame data before clearing them.
Identify the system. Establish the engine, fuel and pump types, low- and high-pressure circuits, control method and correct service data.
Inspect safely. With the system isolated as specified, inspect wiring, connectors, lines, filter and housing for damage, leaks or evidence of contamination. Check the correct fuel and filter are fitted.
Review live data. Compare requested and actual fuel pressure during the complaint, including cranking or load when appropriate. Check that the sensor reading is plausible and the reported units are understood.
Check the low-pressure supply. Measure pressure and delivery using the approved equipment, test points and conditions. Inspect restrictions and air ingress where relevant. Pressure at idle alone does not prove adequate flow under demand.
Check electrical control. On electric pumps, test command, supply and earth under operating conditions. A poor connection or voltage drop can make a sound pump underperform.
Investigate the high-pressure side. Once feed is confirmed, follow the specified checks for the pressure sensor, metering or regulation, pump drive and injector leakage. Do not infer a failed pump from a low-pressure code alone.
Repair the cause and verify. Follow cleaning, replacement, priming and adaptation procedures for the system. Check for leaks by the approved method and repeat the original test.
Use the manufacturer's pressure and flow limits. HELLA's high-pressure pump guide illustrates checking low-pressure supply before assessing the high-pressure circuit. Delphi's voltage-drop guidance explains how a poor electrical connection can imitate a weak pump.
Fuel pressure, flow and control
Illustrative test points in a common-rail system. Test points and limits vary; use the vehicle manufacturer's procedure. Original Tuning Wiki illustration from common-rail fuel system tests.
Pressure and flow answer different questions. A system may reach its target at idle yet fail to deliver enough fuel at higher demand. Compare measurements under the vehicle manufacturer's specified conditions and investigate the filter, pipes, tank pickup and electrical supply before condemning the pump.
On a common-rail engine, low actual pressure can arise from insufficient feed, a regulation or sensor fault, excessive injector return, a mechanical drive issue or pump wear. A scan-tool reading is valuable but is still a sensor signal; use the vehicle's approved independent check where required. See common-rail fuel system tests.
The Bosch CP4 is a family of diesel high-pressure pumps. A cam drives a plunger through a roller and roller shoe or tappet assembly. Designs and vehicle plumbing vary, so identify the installed pump and engine before applying any repair procedure.
In a 2024 response to the US safety regulator, Bosch described several possible damage mechanisms: loss of the lubricating film between roller and shoe, deposits that make a roller sticky, and water-related corrosion or fatigue. Bosch identified fuel properties, high fuel temperature, air, particles and water outside specified limits among possible influencing factors. These are manufacturer-reported mechanisms; the cause of an individual failure must be established from the vehicle and component evidence.
If the roller cannot roll correctly, abnormal sliding and wear can damage the roller, shoe or cam. Progressive damage can generate metallic particles that travel into the fuel system. Do not assume every CP4 fault has the same cause or that a particular bearing has failed merely because rail pressure is low.
Recognising and confirming the problem
Possible complaints include hard starting, a pressure fault, rough running, loss of power or sudden stalling. These are not unique to CP4 damage.
Metallic debris in a fuel component is a significant finding but does not by itself identify its origin or prove the entire system is contaminated. Follow the manufacturer’s specified inspection points and preserve samples and findings.
Absence of visible debris at one inspection point does not rule out internal wear or contamination elsewhere.
Do not dismantle a pressurised pump or remove metering components as a generic shortcut. Use the applicable service procedure and a qualified diesel specialist where needed.
NHTSA's investigation closure for selected 2019–2020 6.7-litre Ram trucks describes a recall involving internal CP4 failure, debris and possible loss of motive power. That finding is scoped to the vehicles and market in the document; it is not a claim that every CP4 installation is recalled. Check the vehicle identification number with the manufacturer or relevant national recall service.
Contamination and repair
If internal pump damage or metallic contamination is confirmed, avoid further unnecessary cranking or running and follow the vehicle manufacturer's contamination procedure. Depending on the system and findings, the assessment can include the pump, metering valve, rail, injectors, high- and low-pressure lines, filter housing, tank, return circuit and feed pump. The prescribed action may be inspection, cleaning or replacement; it is vehicle- and component-specific. A new pump fitted into a contaminated system can be damaged again.
Retain diagnostic readings, photographs, debris samples and repair records. Use the specified fuel and filter and the manufacturer's priming procedure after service. No additive or conversion guarantees prevention; assess modifications against the vehicle maker's requirements and applicable approvals.
Fuel starvation and air-system faults can both cause loss of power. Injector faults can also affect rail pressure or combustion, and poor combustion may contribute to soot loading. A DPF warning, EGR fault or low boost reading needs its own evidence; none alone proves a fuel-pump fault.
Fit the correct components and new seals or pipes where specified. Prime the system and carry out adaptations only as directed. Check for leaks, clear codes when appropriate and compare pressure readings with the original fault conditions. Confirm the starting and driving complaint is resolved and investigate any returning fault.