A common-rail complaint is tested before a pump or an injector is replaced. Fault memory comes first, including a check that the stored code is plausible. Low-pressure and high-pressure measurements come next, even when the controller has stored nothing. Air or a blocked filter on the low-pressure side will pull the rail down, and a new high-pressure pump will not cure it. The hardware those tests are measuring is on common-rail diesel fuel systems, supply pumps and injectors. Hydraulic unit injectors are tested differently: HEUI fuel systems.
For an injector-focused sequence and return-flow equipment limits, see common-rail injector testing on the vehicle.
Before any gauge
Ask what happened, when, in what weather, and whether the complaint followed refuelling. A recent fill and a full gauge justify checking fuel quality; they do not establish contamination. Incorrect fuel can damage the system or affect combustion, so follow the vehicle's fuel-identification and recovery procedure.
Confirm the engine will actually do what the driver described. Read the codes from every module that can stop the fuel, not only the engine controller. Some electronically controlled pumps depend on a networked control module. Check relevant communication, power and command data for the particular vehicle before condemning the pump.
Then the basic mechanical checks, which solve more of these jobs than a parts cannon: oil level, coolant level, a belt that is driving the pump, a blocked air cleaner, battery condition, leaks, fuel actually reaching the pump, injector leak-off, the pump timing mark if the pump is timed, connectors that have been disturbed, and whether the idle is stable once it starts. Do not open a sealed high-pressure part because a connector was loose.
Check cranking speed, battery condition and starter-circuit voltage drop against the engine-specific procedure. Slow cranking can affect both pressure generation and compression temperature; it does not make all pressure or compression readings meaningless.
A diesel needs heat in the chamber and fuel at the right moment. Heat is cranking speed, compression and the glow system. Compression escapes at the head gasket, an inlet valve, an exhaust valve, or the rings. Pressure-pulse and compression tests can help locate leakage, but their interpretation and confirmation depend on the engine and equipment. Check glow-system command and supply under the specified temperature conditions; strategy varies by vehicle.
Do not use starting fluid. Engines are damaged by it, and an engine that has speed, compression and fuel at the right time does not need it.
Low-pressure circuit
The low-pressure circuit is the pipe from the tank to the high-pressure pump, and the return. Inspect the pipes for damage and for air leaks, and inspect the filter. Measurements are examples from particular systems, not limits for every engine. Use the actual vehicle's specifications and approved test conditions:
| Measurement | Figure | If it fails |
|---|---|---|
| Pressure difference across the filter | Use the specified limit at the prescribed flow and conditions. | Investigate restriction in the filter or associated pipework; see Delphi's filter diagnosis. |
| Example electric feed-pump system, between filter and high-pressure pump, while cranking | 2.0 to 2.5 bar | Pump, relay, module, or a blockage upstream. A pulsed returnless petrol pump will not show a steady voltage. Use the pressure. |
| Supply line to the high-pressure pump | Specified positive pressure or suction | Configuration and limits vary by installation; verify feed-pump layout and test conditions. |
| Air in an approved transparent test section | Interpret using the vehicle procedure | Bubbles can indicate air ingress; also check test connections, priming and normal system behaviour. |
| Return circuit | Vehicle-specific | Follow the specified measurement method; pressure and function depend on the system. |
| Pressurised injector return | Vehicle-specific | Some piezo systems need maintained back-pressure and approved adapters. Do not use an incompatible open-bottle test. |
On a Denso system, walk the tank before the pump. Look for a modified tank, a pickup that sits above the residual fuel, a crushed in-tank pipe, internal plating debris, a kinked hose, a split hose, a sedimentor full of water, a priming pump that weeps, a blocked main filter and a blocked gauze at the pump inlet. A rising oil level means fuel is entering the engine, from an injector body, a return seal or a leak-off path, and that is checked before a long crank is called a weak pump.
High-pressure circuit
Follow the vehicle-specific isolation and depressurisation procedure before connecting approved equipment. Keep all opened joints scrupulously clean.
Where the manufacturer specifies a pump-outlet capacity test, a trained specialist uses the correct rated equipment, calibrated restriction, operating conditions and application-specific limit. A pump-outlet test is not the same as measuring the installed rail during cranking. Supply pressure, cranking speed and controls can affect the result. Delphi: a vehicle-specific diagnostic example.
If the approved procedure calls for an independent rail-pressure measurement, a specialist can compare a correctly rated reference instrument with the ECU value at the specified conditions. A disagreement requires checks of the reference instrument, sensor supply, ground, signal, wiring and applicable tolerances before replacing the sensor. Fuel pressure sensor diagnosis.
Some manufacturer scan-tool routines command a controlled rail-pressure or leak check. Use the exact application instructions, prerequisites and approved leak-detection method. A flow damper may restrict a downstream leak and can affect interpretation; do not look for high-pressure spray by touch or smell.
Certain Cummins common-rail applications require a specified rail pressure before injection is enabled. Use the exact engine's starting threshold and test data; a long crank can have several causes. Fuel dilution or a rising oil level warrants prompt investigation of possible fuel-entry paths, which vary by engine.
Some engine-specific diagnostic procedures use a manufacturer-approved isolation tool to locate an internal high-pressure leak. This is a specialist test requiring the exact vehicle procedure, correctly rated equipment and verified depressurisation. Do not improvise a rail plug or open a high-pressure connection while the engine is running or cranking.
Injector return quantity
Excessive injector return is one possible cause of low rail pressure, especially while cranking. Identify the injector and return-circuit design first: some systems require maintained back-pressure and an open-bottle method can be unsuitable or damaging. Use the vehicle and test-equipment instructions, test conditions and limits for the exact installation; neither a percentage spread nor a volume is a universal pass criterion. See on-vehicle injector testing and Pico's test limitations.
Return-flow results are influenced by rail pressure and operating conditions. An outlier warrants investigation, but does not prove nozzle spray or delivery, or establish that the pump is sound. For off-engine testing use the specified bench and test plan. Piezo drive and return arrangements require particular care; do not disconnect a piezo injector electrically while the engine runs. Pico: piezo safety.
What the scan tool is for
Read the codes, then use live data, then an active test. On a Denso system the order is: confirm the symptom, read codes, watch the inputs and outputs, command the outputs with the key on, and if the fault is still there go back to reproducing it. Non-recurring faults are written down properly. The driver’s complaint and the stored data are not always the same fault.
Use the manufacturer's circuit diagram, approved test points and suitable probes. Compare scan data with the measured circuit signal and check supply and ground. Diagnose an open, short or poor connection using the specified isolation and measurement procedure; do not force probes into terminals or damage seals. See intermittent diesel wiring faults.
Rail pressure is an important live-data item on a common rail, but it must be interpreted with the vehicle's diagnostic procedure and the fuel and system condition. On a HEUI engine, injector-control-pressure readings, sensor voltage and regulator command may help; establish whether a scan value is measured or substituted using the exact controller's service data. See HEUI fuel systems.
Cylinder contribution data or an approved cylinder cut-out test identifies a cylinder to investigate, not the failed component. Compression, combustion, wiring and fuel delivery can affect the result. Follow the vehicle-specific procedure and do not apply a single oxygen-sensor voltage threshold to every engine or sensor.
Symptom and the first fuel-system suspects
These are the Denso diagnostic branches for a Toyota-shaped common rail. Glow-system operation, crankshaft position, start signal and ECU supply are useful checks in the relevant diagnostic branches. Requirements and fallback behaviour differ by engine and conditions. The air cleaner is on the list because low air is blamed on injectors.
| Symptom | Fuel-system items in the branch | Check before the pump |
|---|---|---|
| Lamp on | Stored code | Read the code. A lamp circuit that lies is a separate test. |
| Long crank, starter speed normal | Injector, supply pump | Glow actually powered, crank-speed signal present while cranking, cylinder-recognition waveform, start signal at the ECU, ECU supply. |
| Cranks and will not fire | Injector, supply pump | Same electrical list. Then rail pressure against the cranking threshold, then return quantity. |
| Stalls at idle, or stalls as it returns from speed | Injector, supply pump | Overheating, crankshaft signal, ECU supply. A stall on a hot return to idle is often the crankshaft sensor or a rail that will not hold at low delivery. |
| Idle unstable just after start | Injector, supply pump, filter, rail-pressure sensor | Filter and the sensor agreement with a gauge, before a set of injectors. |
| Slow to return to idle, or will not | Injector, supply pump | Accelerator-position sensor. A pedal that still reads open keeps the fuel on. |
| Rough idle | Injector, supply pump | Mechanical vibration, overheating, crankshaft signal. Then contribution and return. |
| No power, poor acceleration | Injector, supply pump | Air cleaner and intake duct, EGR, air-mass meter, boost-pressure sensor, accelerator position. Distinguish air, fuel and control faults with the specified tests. |
| Knock | Injection timing and rate | Too much fuel in the ignition delay. Pilot missing, timing late or early, a nozzle that dribbles, low cetane. |
| Black smoke | Quantity too high for the air | Air filter, EGR that will not shut, boost leak, poor atomisation, retarded timing. |
| White smoke | Fuel that did not burn | Late injection, cold chamber, poor fuel, oil being burnt. White vapour or smoke can have several causes; check glow operation, compression, fuel supply and coolant as appropriate. |
| Poor economy | Quantity, rail pressure, leak-off | The same measurements. Investigate high pressure or excessive leakage using the correct procedure. Normal return fuel is recirculated, so return flow alone does not establish a fuel-economy fault. |
Black smoke generally suggests soot from combustion; white exhaust may contain unburned fuel or water vapour, while blue or blue-grey smoke can indicate oil. Colour and temperature alone do not identify a component. Compare fuel delivery, air supply, combustion and coolant condition as appropriate.
A circuit fault and a separate fuel-delivery problem can coexist. A connector that changes the symptom during an approved wiring check warrants investigation, while a return-flow outlier should be assessed using the correct test and limits. Neither observation alone proves the complete repair.
Petrol fuel pressure and lean faults
Petrol port injection and direct injection have different pressure systems and procedures. Use scan data and the specified pressure, flow and electrical tests for the actual system; a pump with correct pressure at idle can still lack delivery under load. See fuel pump faults.
P0171 indicates a lean condition on bank 1; possible causes include unmetered air, a faulty or contaminated air-mass sensor, fuel supply or injector issues, exhaust leaks and sensor or control faults. Study fuel trims at the relevant operating points and confirm the cause with the appropriate tests rather than replacing an oxygen sensor or injector on the code alone. Delphi: MAF and lean codes; fuel trims.
Injector identity matters: a flow comparison can show one injector different from the others, but does not by itself say which part is correct. Check each part number and vehicle application before concluding that the outlier is faulty. Injector balance and flow tests are system-specific; compare the approved test results and limits, and distinguish electrical response from delivered fuel and spray. See injector diagnosis.
After the repair
After repair, prime the low-pressure system as specified, enter injector codes or carry out adaptations where required, and check for leaks by the prescribed method. Reproduce the original hot, cold or load conditions safely, then review pressure, relevant live data and fault memory. Clear adaptations only when the vehicle-specific procedure calls for it.
For a step-by-step approach to a vehicle that cranks but will not start, see common-rail diesel hard starting and no-start diagnosis.
See also: Automotive diesel injector leak-off and return flow testers for test equipment, interpretation, pressure requirements and documented part numbers.
See also: Automotive diesel fuel pressure and rail pressure test kits for supply-side and common-rail measurement methods, equipment and safety.
See also: Automotive diesel fuel contamination and water-in-fuel testers for sampling, screening methods, equipment and diagnostic limits.
See also: Automotive diesel fuel transfer pumps and priming tools for low-pressure supply, bleeding and transfer equipment and diagnostic uses.
See also: Automotive diesel fuel filter and water separator service tools for filter housing, bowl and sensor tools, service and diagnosis.
See also: Automotive diesel fuel line disconnect tools and quick connector repair kits for low-pressure connector service, repair equipment and limitations.