The crankshaft position sensor (CKP) provides the engine control unit (ECU) with crankshaft speed and position information. A missing or implausible signal can cause a crank-but-no-start, stalling or intermittent running. Wiring, the trigger wheel, battery and mechanical faults can produce similar symptoms, so test the complete circuit before replacing the sensor.

Symptoms and first checks
| Observation | What to investigate |
|---|---|
| Cranks but does not start | Check battery, cranking speed, fault codes, ECU engine-speed data, synchronisation and the CKP circuit; fuel, ignition and compression remain possible causes. |
| Stalls or will not restart when hot | Capture the fault when it occurs and check the sensor signal, supply, wiring and other power or fuel faults. |
| Misfire, hesitation or intermittent loss of speed signal | Inspect the signal under the fault conditions, connector, harness, sensor mounting and trigger wheel. |
| Crank/cam correlation code | Check both signals and the vehicle-specific timing reference; mechanical timing, variable cam timing or a trigger fault may be involved. |
HELLA's crankshaft-sensor guidance lists starting problems, stalling, wiring faults, trigger-wheel damage and contamination among relevant symptoms and causes. A fault code alone does not identify a failed sensor.
What the sensor reads
The CKP sensor detects features on a rotating target such as a crankshaft trigger wheel, pulley or flywheel. The ECU uses the resulting signal for engine speed and timing information. Many engines also use a camshaft position (CMP) signal for phase identification. The ability to start or run with one signal missing varies by system.
Inductive and Hall-effect sensors
An inductive, or variable-reluctance, sensor generates an alternating signal as the target moves; its amplitude and shape depend on speed, air gap and circuit design. A Hall-effect or other active sensor is powered and produces a switched output. Designs and signal voltages vary; some circuits are floating rather than chassis-ground referenced. Identify the actual type and wiring from the vehicle information, not connector pin count or appearance alone.
Use the correct scope inputs, isolation and grounding for the circuit. Do not apply an ohmmeter to an unidentified or active sensor. HELLA cautions that resistance testing can damage a Hall sensor. Only measure a confirmed inductive sensor's resistance when the manufacturer specifies the procedure; an in-range resistance does not prove a good signal under cranking or heat.
Reading a trigger pattern
Some trigger wheels have a deliberate missing-tooth or other reference pattern. A wider gap may therefore be normal; its position is not automatically top dead centre. Other systems use different patterns. Compare with the correct known-good waveform and manufacturer data at a comparable cranking speed or running condition.
Look for unexpected dropouts, irregular spacing, distortion or a signal too weak for the ECU under the fault conditions. Low battery voltage or slow cranking can affect the test. A plausible scan-tool RPM is useful evidence but can be delayed or calculated and does not prove every pulse is correct.
Practical diagnostic sequence
- Record the fault. Note no-start, hot or cold conditions, stalling, recent clutch, timing or sensor work and any mechanical noise. Save all codes and freeze-frame information.
- Check basic starting conditions. Test battery condition and voltage during cranking, starter and grounds using the vehicle procedure. Confirm that the engine turns at the expected speed.
- Identify the sensor and circuit. Obtain the sensor type, wiring, reference pattern and test conditions. Check if the signal is floating before connecting scope grounds.
- Inspect safely. With the engine stopped, examine connectors, harness routing, heat damage, mounting and accessible contamination. Inspect the target and air gap only as the manufacturer directs.
- Review live data. Observe engine speed and crank/cam synchronisation while the fault is present where supported. Absence of RPM directs further tests but is not conclusive proof of a bad sensor.
- Capture the signal. Use the specified scope setup while cranking or running under the fault conditions. Check supply and ground on active sensors; compare waveform and timing with the correct reference.
- Check the ECU input and wiring. If the signal is present at the sensor but not at the ECU, follow the prescribed harness and connector checks. A good signal at the ECU does not automatically prove its interpretation or mechanical timing.
- Check crank/cam correlation when indicated. Compare simultaneous signals with the correct engine reference, accounting for variable valve timing and test conditions. Investigate mechanical timing and trigger-wheel installation where the evidence warrants it.
- Repair and verify. Correct the cause, fit the specified sensor and seal, perform any required learn procedure, then repeat the original start or driving test and review fault memory.
Keep clear of belts, fans and rotating components while cranking. Secure test leads and use a second person where appropriate. Do not repeatedly crank an engine if the manufacturer’s procedure or the fault suggests a risk of mechanical damage.
Crank and cam correlation
Correlation faults can arise from a sensor or wiring problem, a damaged or incorrectly fitted trigger wheel, mechanical timing error or variable valve timing fault. A waveform comparison can help distinguish them, but only against the correct engine, software and operating conditions. Pico's crank/cam comparison describes both electrical and mechanical possibilities.
Generic P0335–P0339 codes commonly concern the crankshaft sensor circuit, range, low, high or intermittent signal; correlation and camshaft codes are separate. Use the full manufacturer-specific definition, bank or sensor identification and test plan.
Replacement and verification
Use the correct sensor for the engine and target wheel. Check the mounting surface, seal and specified air gap; use only the manufacturer's installation method. Do not assume a similar connector means the electrical design or calibration is interchangeable. Some vehicles require a crankshaft variation or position learn after specified repairs, while others do not.
Confirm reliable starting hot and cold if relevant, capture a signal under the original fault conditions, check for returning codes and complete required relearns. If the problem remains, revisit power supply, wiring, synchronisation, fuel and engine mechanical checks.
Related diagnostic guides
- AdBlue and SCR system faults — fluid supply, dosing and SCR efficiency checks.
- NOx sensor faults — NOx measurement, wiring and SCR checks.
- DPF differential pressure sensor faults — pressure hoses, sensor readings and filter restriction.
- Exhaust gas temperature sensor faults — exhaust temperature, wiring and regeneration checks.
- Intake air temperature sensor faults — air temperature, wiring and heat-soak checks.
- Knock sensor faults — knock sensing, wiring and combustion checks.
- Accelerator pedal position sensor faults — pedal input and acceleration response checks.
- Throttle position sensor faults — throttle feedback and response checks.
- Camshaft position sensor faults — starting and crank/cam synchronisation checks.
- Coolant temperature sensor faults — starting and warm-up data.
- Oxygen sensor faults — mixture and misfire look-alikes.
- MAP and MAF sensor faults — pressure and airflow inputs.
- Fuel pressure sensor, fuel pump and injector faults — fuel-related no-start checks.
- DPF faults, EGR faults, turbo diagnostics and boost leaks — related drivability investigations.