Injector catalogue › Petrol injectors › ASNU testing
ASNU injector testing makes an injector's electrical condition, leakage, spray and delivery observable under controlled bench conditions. A useful service records each injector before any approved cleaning, repeats the relevant tests afterwards, and keeps the test settings with the results. The steps and capabilities depend on the injector, ASNU model and available adapters.

Choose the guide
- ASNU port injector testing — identify, mount, leak-test, inspect spray and measure dynamic and static delivery.
- ASNU GDI injector testing — high-pressure petrol injectors, solenoid and piezo drivers, low-pressure bench interpretation and limitations.
- Test results and flow calculations — test conditions, cc/min, per-injection volume, matching and a report checklist.
- Cleaning and refitting — appropriate cleaning, serviceable filters and seals, retesting and vehicle-specific reinstallation.
What the ASNU machine does
An ASNU test bench holds compatible injectors in a rail, supplies test fluid and drives each injector through a controlled cycle. The technician observes spray through the viewing area, checks for leaks and measures delivered fluid using the machine's measuring equipment. ASNU's Classic GDI brochure lists up to eight injectors, a leak check, spray observation, static and dynamic functions, individual selection and an ultrasonic bath. Not every function or accessory applies to every injector.
The Classic GDI lists GDI drive and solenoid inductance checking, with a separate piezo adapter listed as an option. ASNU describes the Junior as testing up to six injectors and requiring an optional GDI box for compatible GDI work. Verify the precise model, firmware, harness, rails and approved test method rather than assuming every ASNU setup supports every injector. See ASNU's equipment information.
Practical sequence
- Identify: record part and cylinder numbers, symptoms, injector type and any calibration/index code; inspect for obvious damage.
- Prepare: select the proper rail, seals, connector and electrical driver; use the approved test fluid and specified conditions. Keep each injector tied to its receiving channel.
- Establish the baseline: run the supported electrical, closed-injector leak, spray and pulsed-flow checks; include static flow where appropriate. Record each individual result and test setting before service.
- Service only if permitted: use the method and parts approved for that injector. Cleaning, filter replacement and ultrasonic treatment are not suitable for every design.
- Retest and report: repeat the relevant checks at comparable settings, note remaining defects and record the outcome for each injector. Follow the vehicle maker's instructions for seals, installation, coding and post-repair checks.
This sequence follows the approach described in Llandow Tuning's ASNU petrol-injector service; exact test order and the available service parts vary with the injector and machine.
Port versus direct injection
Port injectors generally use a lower-pressure manifold rail. GDI injectors spray into the cylinder and can require dedicated high-current or piezo drive, specific sealing and different removal tools. An injector's colour, plug or physical size does not by itself identify its drive or interchangeable replacement.
ASNU describes the Classic GDI as a lower-pressure comparison bench: its brochure states a maximum of 10 bar for the machine described and gives 75–200 bar for some vehicle GDI systems. The low-pressure test can expose differences in spray and sealing, but a good result does not certify operation at the vehicle's higher rail pressures or under every heat and load condition. Follow up unexplained vehicle symptoms with the vehicle and injector manufacturer's diagnostic process. ASNU Classic GDI brochure; ASNU's low-pressure testing paper; Llandow's GDI limitations.
ASNU resources
- ASNU catalogues and brochures — Classic GDI, GDI/FSI and piezo boxes, remote software, report sheet, and injector-specific service tips.
- ASNU instructional videos — Remote Control Program usage, GDI low-pressure testing, Siemens piezo tests, insulation checking, filter and seal tools.
- ASNU Remote Control Software and Digital Flow Kit — optional computer control, test information and results on compatible equipment.
- ASNU test and cleaning fluids — FlowRite for testing and Bio-Clean for the ultrasonic bath as specified by ASNU.
For injector identification and flow references see the port injector catalogue, direct injector catalogue and ASNU performance injector catalogue.