Injector catalogue › Petrol injectors › ASNU testing
Testing guides: Port injectors | GDI injectors | Results and flow calculations | Cleaning and refitting.
Cleaning is a conditional part of injector service, not proof that a damaged injector has been repaired. Establish the baseline first, confirm that the specific injector may be serviced in the chosen way, and retest at the original settings. Llandow Tuning's process describes external inspection, initial leak and delivery checks, service where appropriate, and before/after recording.
Decide whether the injector is serviceable
Read the injector manufacturer's and bench manufacturer's instructions for the exact part and its materials. An integrated filter, tip or seal may not be removable or available separately. Do not remove material from a nozzle to imitate a spray pattern and do not assume a replacement screen or cap for one family fits another. If the body, connector or nozzle is damaged, or the approved procedure cannot be established, refer to a specialist or replace the part as directed.
There is no universal ultrasonic time, temperature, immersion depth, solution or driving programme. For example, the Bosch Motorsport HDEV 5.2 datasheet explicitly says not to use ultrasonic cleaning on that particular injector. ASNU describes cleaning cycles for compatible injectors; that capability does not override an injector manufacturer's restriction.
Test and cleaning fluids are different
ASNU identifies FlowRite as injector test/measurement fluid and Bio-Clean as ultrasonic-bath cleaning fluid. Use the approved product and the instructions for the machine and injector; do not put bath cleaner in the measurement circuit or assume pump petrol is the correct bench fluid. ASNU's fluid guidance describes each product. Control contamination and dispose of used liquids according to the applicable workshop procedure.
Filters, caps and seals
Where the exact design supports service, use the correct removal and insertion tooling and replace service parts with the specified components. Preserve the nozzle and bore; avoid pushing debris further inside. ASNU publishes separate instructions for Delphi MPI filter removal and a Siemens piezo filter and ASNU 219/219T tool. The separate tools and procedures are an example of why one generic filter-removal method is unsafe.
If a filter has disintegrated, record it and investigate where the missing material may have gone. In its Siemens piezo guidance, ASNU recommends replacement when a removed filter has broken up because fragments may be inside. That recommendation is specific to its identified situation; follow the applicable manufacturer's decision for other parts.
Repeat and record the test
After the approved service and reassembly, repeat the applicable leakage, spray and flow tests under the same recorded conditions as the baseline. A result that improves but remains outside an applicable specification needs further investigation. A leak, damaged body or visibly defective spray is not cleared by a good flow number. Avoid promising that cleaning will restore every injector.
Refitting to the vehicle
Use the vehicle maker's procedure for the exact engine: replacement seals, any single-use pipes or fasteners, approved lubricants, tightening sequence and torque. For its own performance injectors, ASNU specifies fresh O-rings on refitting and a clean non-silicone oil for the stated O-rings; that is not a universal lubricant instruction for every GDI combustion seal.
GDI seals can need dedicated fitting and sizing tools and have different orientation and handling rules. Compare ASNU's Nissan Qashqai GDI seal note with Bosch's high-pressure injector guidance; do not transfer one injector's seal instructions to another. Refit to the correct cylinder or update the ECU's injector data when required. BMW's N63 training manual gives one petrol piezo example that requires adjustment after replacement.
Once the system is correctly assembled, perform the manufacturer's priming, leak check and diagnostic checks. A bench report describes the tested injector under the recorded conditions; it does not prove that a vehicle's pump, rail, wiring, compression or mixture control is sound.
Sources
- Llandow Tuning injector service workflow.
- ASNU fluids; ASNU performance injector fitting instructions.
- Bosch HDEV 5.2 data sheet; ASNU Delphi MPI filter tip; ASNU Siemens piezo filter tip; ASNU Nissan GDI seal tip.
- Bosch high-pressure injector installation guidance; BMW N63 engine reference manual.
See also: Automotive injector cleaning and flow testing machines for bench methods, equipment examples and diagnostic limitations.