Tuning Wiki

Injector catalogue › Petrol › Port | Direct | Diesel

This catalogue lists representative manifold/port injectors, including their manufacturer numbers. Flow alone does not establish interchangeability: check measured installation length, rail and manifold seals, nozzle and spray targeting, connector, electrical drive and the ECU's injector-characterisation data.

A Deka VII petrol fuel injector
Deka VII port-injector example; the photograph is illustrative and is not identified as any particular entry below. Photo: David DeGrace via Wikimedia Commons, CC BY-SA 3.0; unchanged.

For testing these injectors, see ASNU port injector testing and understanding flow results.

Bosch Motorsport EV 14

The following Bosch EV 14 ordering information gives mass flow in n-heptane at 3 bar. Approximate volume is calculated from Bosch's stated n-heptane density of 0.684 g/cm³: cc/min = g/min ÷ 0.684. These figures describe the test fluid; they are not a claim that a different fuel has the same mass flow or that the injectors are interchangeable. Pressure is the differential across the injector.

Bosch order numberTypen-heptane g/min at 3 barCalculated n-heptane cc/min
0 280 158 013 (0280158013; 0280 158 013)EV 14 ES150≈219
0 280 158 038 (0280158038; 0280 158 038)EV 14 CKxT237≈347
0 280 158 116 (0280158116; 0280 158 116)EV 14 EL237≈347
B280 436 038-09 (B280436038-09)EV 14 CS387≈566
B280 436 038-10 (B280436038-10)EV 14 CS387≈566
0 280 158 123 (0280158123; 0280 158 123)EV 14 ESxT429≈627
B280 436 038-07 (B280436038-07)EV 14 CS503≈735
B280 436 038-08 (B280436038-08)EV 14 CS503≈735
0 280 158 040 (0280158040; 0280 158 040)EV 14 CKxT670≈980
B280 436 487-01 (B280436487-01)EV 14 CS670≈980

Even equal-flow entries can have different spray patterns. Bosch identifies the -07/-08 and -09/-10 motorsport versions as differing in spray angle; consult the specific drawing and Bosch basic information before choosing an injector.

Bosch EV 6 and common production-derived examples

The Bosch Motorsport EV 6 datasheet lists n-heptane mass flows at 3 bar. The approximate volume column is calculated using 0.684 g/cm³; it is n-heptane, not a separately measured petrol rating.

Bosch numberVersiong/min at 3 barCalculated n-heptane cc/min
0 280 156 194 (0280156194; 0280 156 194)EV 6 CS116≈170
0 280 155 868 (0280155868; 0280 155 868)EV 6 CL261≈382
0 280 155 830 (0280155830; 0280 155 830)EV 6 EL261≈382
0 280 156 063 (0280156063; 0280 156 063)EV 6 ES269≈393
0 280 156 012 (0280156012; 0280 156 012)EV 6 CS310≈453
B 280 434 499-02 (B280434499-02)EV 6 CS658≈962

Bosch Brazil's 2021 performance catalogue separately lists 0 280 155 968 (0280155968), often called the green injector, at 431 cc/min at 3 bar; 0 280 156 086 (0280156086) at 294 cc/min; and 0 280 156 453 (0280156453) at 683 cc/min. Its illustrated tables do not identify the test fluid alongside those values. The same source lists 935 cc/min for 0 280 158 040 at 3 bar, whereas the n-heptane calculation above gives approximately 980. The test bases are not established as equivalent; preserve the source and conditions instead of treating either figure as a universal rating.

Toyota / Denso port examples

The Tomco port-injector catalogue supplies the historical application examples. The separate Stan Weiss flow-data compilation supplies the first three flow figures; the test fluid is not clearly specified for those individual entries. These independent references are not a current vehicle fitment guarantee.

Toyota / Denso referenceExample application from sourceReported flow and pressure
23250-74040 (2325074040); 195500-51601990–1992 MR2 2.2 5S-FE, selected market289.6 cc/min at 2.5 bar
23250-74090 (2325074090)1990–1995 MR2 / 1990–1993 Celica 2.0 3S-GTE, selected market439.8 cc/min at 2.5 bar
23250-49035 (2325049035)1994 Supra 3.0 2JZ-GTE, selected market529.7 cc/min at 2.5 bar
23250-46050 (2325046050); Denso 195500-56401995 Supra 3.0 2JZ-GE, selected market312 cc/min at 3 bar, supplier listing; volume test fluid not stated

Siemens Deka examples

CPR Racing's 2026 service catalogue lists these nominal flows and body/connector descriptions. Its entries do not state test pressure or test fluid alongside these listings. Figures are therefore labelled as catalogue nominal cc/min, not independently normalised to 3 bar. EV1/EV6 terms are used inconsistently by suppliers; use the actual connector description and drawing.

Deka numberNominal cc/minListed configuration
108420441Jetronic; short 48 mm
107961630Jetronic
107962630Jetronic; short 48 mm
108191630USCAR; standard length
110324840Jetronic; standard length
109991840USCAR; standard length
1103332,226Jetronic; standard length

Injector Dynamics

ID1050x / ID1050-XDS product data lists 1,065 cc/min at 3.0 bar using petrol at 52 °C, USCAR connector, and different complete part numbers for the fitments. For example, 1050.34.14.14 is a listed universal configuration. Get pressure-dependent flow, offset and exact fitment data from Injector Dynamics.

ASNU

See the separate ASNU performance injector catalogue for basic ASNU numbers, nozzle angles and a direct link to its illustrated 2026 catalogue.

Using flow data

For an unchanged liquid and an injector in a suitable static-flow regime, Bosch gives Q₂ = Q₁ × √(ΔP₂/ΔP₁). Use pressure difference across the injector, not just gauge rail pressure, and confirm the result by test. This approximation does not supply dead-time, short-pulse behaviour, electrical drive, or spray information. See Bosch injection-valve basic information.

Sources