Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Airflow
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

What this section is

An airflow meter tells the control unit how much air the engine is taking, so injection, ignition and, on some cars, the gearshift can follow the load. The meter sits between the air cleaner and the throttle. Everything downstream of it, including a leak, is air the meter did not count.

There are two families. A volume meter reports how much space the air occupies. A mass meter reports how much air that volume actually contains, so a cold morning and a hot afternoon do not need a separate density correction for the main signal. Speed-density systems have no meter at all: they estimate the mass from manifold pressure, air temperature, throttle position and engine speed. That pressure sensor, and the boost sensor on a turbocharged engine, are in manifold and boost pressure sensors.

Meter types

Vane airflow meters measure volume with a spring-loaded flap and a potentiometer. This is the air vane on Bosch L-Jetronic, early Toyota, Nissan and Ford EFI. Hot-wire MAF sensors hold a platinum wire above the air temperature and read the current that keeps it there. Denso, Bosch LH-Jetronic and the Hitachi meters on Nissan are this type. Hot-film MAF sensors use a printed or micromechanical film instead of a free wire. Bosch HFM, Siemens VDO, Pierburg and the early GM Delco meters are this type. The signal may be a voltage or a frequency. Karman vortex meters count the vortices shed by a blunt body. Toyota used an optical pickup. Mitsubishi Electric used ultrasonics. Both report volume, as a rising frequency.

The K-Jetronic sensor plate is a mechanical cousin of the vane. Air lifts a plate and a control plunger meters fuel directly. It does not produce an electrical airflow signal.

Makers

The same technology is sold under several names. Who makes airflow meters covers Bosch, Denso, Hitachi, Mitsubishi Electric, Siemens VDO, Pierburg, Delphi and the Ford and Fiat-group suppliers, and which technology each one actually used.

Bosch film meters, in numbers

HFM 2 thick-film bridge, four curves, four-pin plug, no burn-off. HFM 5 micromechanical film, return-flow detection, five housings and the voltage table. HFM 7 adds the deflection bypass. The insert and the tube are calibrated together. Siemens VDO SIMAF and the 20.3855, and the maf2maf converter that maps one curve onto the other. POSiFA PMA1000 programmable module for a customer housing. Pierburg frequency meter on the 1.6 HDi and TDCi. Frequency falls as flow rises.

Using the signal

Test figures for the common families, including the GM and Ford codes, are on hot wire, hot film, vane and Karman measurements. Nissan plug pins are on Nissan MAF pinouts and Consult. The 1.9 TDI Bosch and Pierburg curves, and the mg/stroke conversion, are on Volkswagen TDI air-mass measurement. Replacing a vane with a mass-air sensor is AFM to MAF conversion.

A control unit does not see kilograms per hour. It sees a voltage or a frequency and looks that up on the curve stored for that exact meter. A different maker’s sensor, or the same maker’s sensor with a different part number, can be electrically healthy and still report the wrong mass.

For sensor transfer curves, logging and examples across factory and standalone controllers, see MAF calibration across ECU types.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Airflow metering

What this section is

An airflow meter tells the control unit how much air the engine is taking, so injection, ignition and, on some cars, the gearshift can follow the load. The meter sits between the air cleaner and the throttle. Everything downstream of it, including a leak, is air the meter did not count.

There are two families. A volume meter reports how much space the air occupies. A mass meter reports how much air that volume actually contains, so a cold morning and a hot afternoon do not need a separate density correction for the main signal. Speed-density systems have no meter at all: they estimate the mass from manifold pressure, air temperature, throttle position and engine speed. That pressure sensor, and the boost sensor on a turbocharged engine, are in manifold and boost pressure sensors.

Meter types

  • Vane airflow meters measure volume with a spring-loaded flap and a potentiometer. This is the air vane on Bosch L-Jetronic, early Toyota, Nissan and Ford EFI.
  • Hot-wire MAF sensors hold a platinum wire above the air temperature and read the current that keeps it there. Denso, Bosch LH-Jetronic and the Hitachi meters on Nissan are this type.
  • Hot-film MAF sensors use a printed or micromechanical film instead of a free wire. Bosch HFM, Siemens VDO, Pierburg and the early GM Delco meters are this type. The signal may be a voltage or a frequency.
  • Karman vortex meters count the vortices shed by a blunt body. Toyota used an optical pickup. Mitsubishi Electric used ultrasonics. Both report volume, as a rising frequency.

The K-Jetronic sensor plate is a mechanical cousin of the vane. Air lifts a plate and a control plunger meters fuel directly. It does not produce an electrical airflow signal.

Makers

The same technology is sold under several names. Who makes airflow meters covers Bosch, Denso, Hitachi, Mitsubishi Electric, Siemens VDO, Pierburg, Delphi and the Ford and Fiat-group suppliers, and which technology each one actually used.

Bosch film meters, in numbers

  • HFM 2 thick-film bridge, four curves, four-pin plug, no burn-off.
  • HFM 5 micromechanical film, return-flow detection, five housings and the voltage table.
  • HFM 7 adds the deflection bypass. The insert and the tube are calibrated together.
  • Siemens VDO SIMAF and the 20.3855, and the maf2maf converter that maps one curve onto the other.
  • POSiFA PMA1000 programmable module for a customer housing.
  • Pierburg frequency meter on the 1.6 HDi and TDCi. Frequency falls as flow rises.

Using the signal

Test figures for the common families, including the GM and Ford codes, are on hot wire, hot film, vane and Karman measurements. Nissan plug pins are on Nissan MAF pinouts and Consult. The 1.9 TDI Bosch and Pierburg curves, and the mg/stroke conversion, are on Volkswagen TDI air-mass measurement. Replacing a vane with a mass-air sensor is AFM to MAF conversion.

A control unit does not see kilograms per hour. It sees a voltage or a frequency and looks that up on the curve stored for that exact meter. A different maker’s sensor, or the same maker’s sensor with a different part number, can be electrically healthy and still report the wrong mass.

For sensor transfer curves, logging and examples across factory and standalone controllers, see MAF calibration across ECU types.

Revision 3: Airflow metering

What this section is

An airflow meter tells the control unit how much air the engine is taking, so injection, ignition and, on some cars, the gearshift can follow the load. The meter sits between the air cleaner and the throttle. Everything downstream of it, including a leak, is air the meter did not count.

There are two families. A volume meter reports how much space the air occupies. A mass meter reports how much air that volume actually contains, so a cold morning and a hot afternoon do not need a separate density correction for the main signal. Speed-density systems have no meter at all: they estimate the mass from manifold pressure, air temperature, throttle position and engine speed. That pressure sensor, and the boost sensor on a turbocharged engine, are in manifold and boost pressure sensors.

Meter types

  • Vane airflow meters measure volume with a spring-loaded flap and a potentiometer. This is the air vane on Bosch L-Jetronic, early Toyota, Nissan and Ford EFI.
  • Hot-wire MAF sensors hold a platinum wire above the air temperature and read the current that keeps it there. Denso, Bosch LH-Jetronic and the Hitachi meters on Nissan are this type.
  • Hot-film MAF sensors use a printed or micromechanical film instead of a free wire. Bosch HFM, Siemens VDO, Pierburg and the early GM Delco meters are this type. The signal may be a voltage or a frequency.
  • Karman vortex meters count the vortices shed by a blunt body. Toyota used an optical pickup. Mitsubishi Electric used ultrasonics. Both report volume, as a rising frequency.

The K-Jetronic sensor plate is a mechanical cousin of the vane. Air lifts a plate and a control plunger meters fuel directly. It does not produce an electrical airflow signal.

Makers

The same technology is sold under several names. Who makes airflow meters covers Bosch, Denso, Hitachi, Mitsubishi Electric, Siemens VDO, Pierburg, Delphi and the Ford and Fiat-group suppliers, and which technology each one actually used.

Bosch film meters, in numbers

  • HFM 2 thick-film bridge, four curves, four-pin plug, no burn-off.
  • HFM 5 micromechanical film, return-flow detection, five housings and the voltage table.
  • HFM 7 adds the deflection bypass. The insert and the tube are calibrated together.
  • Siemens VDO SIMAF and the 20.3855, and the maf2maf converter that maps one curve onto the other.
  • POSiFA PMA1000 programmable module for a customer housing.
  • Pierburg frequency meter on the 1.6 HDi and TDCi. Frequency falls as flow rises.

Using the signal

Test figures for the common families, including the GM and Ford codes, are on hot wire, hot film, vane and Karman measurements. Nissan plug pins are on Nissan MAF pinouts and Consult. The 1.9 TDI Bosch and Pierburg curves, and the mg/stroke conversion, are on Volkswagen TDI air-mass measurement. Replacing a vane with a mass-air sensor is AFM to MAF conversion.

A control unit does not see kilograms per hour. It sees a voltage or a frequency and looks that up on the curve stored for that exact meter. A different maker’s sensor, or the same maker’s sensor with a different part number, can be electrically healthy and still report the wrong mass.

For sensor transfer curves, logging and examples across factory and standalone controllers, see MAF calibration across ECU types.