Constant-temperature hot wire
A hot-wire mass-airflow sensor is a constant-temperature anemometer. A fine platinum wire is heated by an electric current. Incoming air carries that heat away. A control circuit raises or lowers the current so the wire stays a fixed temperature above the air around it. More mass flow takes more heat, so the circuit supplies more current. That current is the measurement. Electronics in the housing turn it into a voltage, or less often a frequency, for the control unit.
Heat leaves the wire according to how many molecules pass it and how cold they are relative to the wire. That is the mass of the air, including the effect of humidity. A vane still needs a separate temperature correction to approach the same answer. A hot wire has already made it.
A thermistor, the cold wire, sits in the same airstream and is not heated as a sensor. It measures incoming-air temperature so the hot wire’s target can stay a fixed amount above that temperature as the day changes. On many housings this thermistor is also brought out as the intake-air temperature signal, on its own pin and often its own ground. The Toyota arrangement is that split: one ground for the meter, a separate ground for the temperature sensor.
How hot the wire is
The offset is not one number for every maker. On the Bosch and the early GM tuned-port hot wires, the platinum wire is held about 100 °C (212 °F) above the incoming air. Another description, used for a different hot-wire construction, holds the wire near 200 °C and treats the current that maintains that temperature as the flow signal. Both are constant-temperature meters. The test limits of one do not transfer to the other. A hot-film foil, which is a different element, has been described as held about 75 °C (167 °F) above the surrounding air. That figure belongs on the hot-film page.
Burn-off
A bare platinum wire collects dust and oil. The layer insulates the wire, less current is needed to hold temperature, and the meter reports less mass than is really flowing. In open loop the mixture goes lean. At light load a narrowband sensor can hide it. At wide-open throttle it cannot.
Bosch LH-Jetronic, and the 1985–89 GM 5.0 and 5.7 litre tuned-port engines that used the same Bosch wire, burn the deposit off after shutdown. The control unit, through a relay, heats the wire to about 1000 °C for one second. On those GM cars, code 36 is a burn-off that did not happen. Power for running and power for the burn-off are separate relays. The feed is the orange-and-black wire, ground is black, and the signal is the brown-and-white wire. Back-probed at terminal B6 of the PCM, that signal is checked around 2.5 V and must rise as the throttle opens with the engine running. Idle on these analogue Bosch wires is usually 0.4 to 0.8 V, and wide-open throttle is 4.5 to 5.0 V.
Early Denso wires on Toyota, including 1980s performance engines, use the same idea: a burn-off after shutdown. Later Denso slot sensors do not. There is no burn-off relay and no cleaning temperature. A missing burn-off on a sensor that never had one is not a fault.
Nissan’s early Hitachi wires bring a cleaning pin and a calibration-potentiometer pin out to the plug. On the RB30 and VG30 looms those pins are present and not used. The published colours are on Nissan MAF pinouts. Output on those early meters is about 2 to 7 V, not the 0 to 5 V of a later sensor.
Full-flow wire and bypass wire
Some meters put the wire in the main bore. Others put it in a small bypass or sampling tube and infer the total flow from the sample. The inference holds while the flow in the main bore is even. A cone filter clamped on the inlet, a tight bend immediately upstream, or a sensor sat at the wrong angle makes the sample unrepresentative. The engine then hunts or goes flat in one load range while the wire itself is electrically fine.
Denso used both constructions. The earlier Toyota meters are a measuring tube with the wire in a bypass passage inside that tube. From the late 1990s the common Toyota and Lexus meter is a plug-in slot: the element samples a shaped passage in the air-cleaner housing or a straight duct, and the slot is calibrated for that housing. Turning the insert, or swapping an insert into a different housing, changes the sample. The voltage can still look sensible and the mass is wrong.
Denso
Denso is the hot-wire supplier for Toyota and Lexus, and the same construction appears where Denso supplied other Japanese petrol engines. The element is a platinum hot wire and an air-temperature thermistor. On the later sensors the signal is a voltage that rises with mass flow, generally inside a 0 to 5 V span. Intake-air temperature is commonly a separate output in the same connector.
An oil film from an over-oiled gauze filter, or dust from a torn paper element, is the usual Denso failure that sets no code. Reported mass falls, open-loop fuel goes lean, and the car hesitates when the throttle is opened. Cleaning belongs on the element, with a cleaner made for these sensors. Brake cleaner and other electrical solvents leave their own film. The element is a fine wire. Do not poke it.
A worked hot-wire example, from a different family, sat at about 0.5 V at idle when healthy and at about 2.0 V at idle when the wire circuit had gone high-resistance. That pair is not a Denso limit. Resistance checks use the diagram for the car in front of you. With the engine idling, confirm feeds and earths before condemning the element. Use a breakout lead for the waveform. Piercing the insulation is the next fault.
Bosch LH and Hitachi
Bosch’s hot wire is the LH-Jetronic meter and the GM tuned-port meter described above. Later Bosch systems moved to the thick-film and then the micromechanical hot film, which does not need a burn-off cycle.
Hitachi supplied the hot-wire meters used with Nissan ECCS through the RB, VG, CA and SR years. Early plugs are the 2 to 7 V meters with the unused cleaning and calibration pins. Later plugs are a simpler set: 12 V, ground and a signal. The R35 and Z33 insert adds intake-air temperature pins that are not connected on that particular insert. Treat the pin table for the chassis as the authority. The plug shape alone does not say which generation it is.
A film or a vortex can look similar
A hot film can look identical from the outside: a module in the intake tract, a rising voltage, an air-temperature pin. The element is a printed or micromachined resistor on a substrate, rather than a free platinum wire, and the self-clean behaviour is different. A Karman meter also lives in the intake tract and also produces a signal that rises with airflow. That signal is a frequency that counts vortices, and it measures volume. Reading a Karman meter, or a frequency-output film, against the 0.4 to 0.8 V Bosch idle figure will condemn a sensor that is doing what it was built to do.