Tuning Wiki

For a practical diagnostic checklist with pictures, see common MAP sensor faults.

What this section is

A manifold-pressure sensor tells the control unit the absolute pressure of the air in the intake. On a naturally aspirated engine that pressure is the load signal. On a turbocharged engine the same kind of sensor, with a higher range, reads the pressure in the manifold or in the charge pipe after the compressor. Both are absolute. Neither reads boost as a number above atmosphere.

Absolute pressure includes the atmosphere. With the engine stopped at sea level the sensor sits near 100 kPa, not at zero. Gauge boost is what is left after barometric pressure is subtracted. A sensor that has reached 250 kPa absolute is at about 1.5 bar of boost only when the barometer is near 100 kPa. At altitude the same absolute reading is more boost, and the control unit can only know that if it has a barometric reading as well.

The airflow meter is a different instrument. It sits in the intake tract and reports mass or volume directly. Speed-density has no meter: it estimates the mass in one intake event from this pressure, the air temperature, the engine speed and a volumetric-efficiency model. The meter types are on airflow metering.

Where the sensor sits

  • Manifold absolute pressure, after the throttle. This is the load sensor on a speed-density engine, and a plausibility check on many engines that also have an airflow meter.
  • Boost or charge pressure, after the compressor and usually before the throttle. Same measurement, higher range, and the value the boost controller is trying to hold.
  • Barometric pressure. Sometimes a second sensor, sometimes the manifold sensor read at key-on before the engine turns, and sometimes a cell inside the control unit.

A differential sensor across a diesel particulate filter, and a rail-pressure sensor on a common-rail pump, are not this part. They can share a maker and a plug style. The range is tens of kilopascals to a few hundred for manifold and boost air. Rail pressure is hundreds of bar.

What the control unit actually receives

The usual production sensor is a piezoresistive silicon diaphragm with a sealed vacuum behind it, so the signal is absolute. A circuit on the same chip amplifies that and compensates temperature. The output is a voltage that is ratiometric: it is a fraction of the 5 V supply, not a fixed number of volts. A supply that has sagged to 4.8 V scales the whole curve. Reading the signal against a battery ground, or against a different 5 V from the one that feeds the sensor, shifts the pressure.

Some sensors add an NTC in the same housing and a fourth pin. That is a T-MAP. The temperature curve is not the pressure curve, and a dead temperature element does not by itself prove the pressure element is dead.

Ford’s EEC-IV MAP and BARO sensors are the exception in this section. They put out a frequency, not a ratiometric voltage. The table is on Ford MAP and BARO frequency sensors.

The part number is the calibration

A control unit does not see kilopascals. It sees a voltage or a frequency and looks that up on the curve stored for that exact sensor. Two Bosch sensors in the same housing can be 20 to 115 kPa and 20 to 300 kPa. At the same true pressure they produce different voltages, and a voltage that is legal for both will not set an electrical fault. The engine then runs on the wrong load.

The published curves and the pin orders, which are not the same from one Bosch housing to the next, are on Bosch absolute-pressure sensors. The motorsport parts, which print a sensitivity and an offset, are on Bosch Motorsport air-pressure sensors. The silicon elements used loose, and inside many other makers’ sensors, are on NXP MPX absolute pressure sensors. Who built which kind of sensor is on manifold pressure sensor manufacturers.

A reading that is in range and still wrong

  • The hose or the O-ring leaks, so the sensor sees somewhere between manifold and atmosphere. The voltage looks alive.
  • Condensate collects in a port that points upwards. Bosch mounts the pressure fitting downwards for that reason.
  • The replacement is the right plug and the wrong range.
  • The signal is read against the wrong ground, or the 5 V reference is shared with a load that pulls it down.
  • On a frequency sensor, a DC voltmeter is the wrong instrument. The wire is switching.

Key-on, engine stopped, is the check that does not need a road. The reported absolute pressure should agree with a barometer at that altitude. A 1 bar sensor near 4.5 V and a 3 bar sensor near 1.6 V can both be telling the truth about the same atmosphere. They are not interchangeable.