Tuning Wiki

The same job, several makers

An airflow meter is rarely unique to the car badge on the grille. The car maker specifies the curve, the plug and the housing. The sensor maker builds the element. Swapping a Bosch film for a Denso wire because both are called a MAF gives the control unit a voltage it will interpret on the wrong curve. This page is which maker used which technology. Curves and pins for a particular part stay on that part’s page.

MakerTechnologyWhere it turns up
BoschVane, then hot wire, then hot filmL-Jetronic, LH-Jetronic, Motronic, and many European and GM installations
DensoHot wireToyota and Lexus, and other engines Denso supplied
Hitachi, earlier JECSHot wire, and a high-frequency hot filmNissan ECCS; GM 3.3 and 3.8 after 1990
Mitsubishi ElectricKarman vortex, ultrasonicMitsubishi petrol engines of the 1980s and 1990s
Siemens VDO, later ContinentalHot film, fixed or programmableEuropean petrol and diesel, including the 20.3855
PierburgHot film, voltage or frequencyVolkswagen diesels, PSA and Ford 1.6 diesels
Delphi, earlier AC Rochester and DelcoHot film, frequencyGM petrol engines from 1984 until most of them went speed-density
Ford / MotorcraftVane, then hot wireFord electronic injection
Magneti MarelliVane era, then hot filmFiat-group engines

Bosch

Bosch is the maker whose generations are easiest to separate by name. L-Jetronic uses the vane. LH-Jetronic, and the 1985–89 GM 5.0 and 5.7 tuned-port engines, use the hot wire with a one-second burn-off after shutdown. The thick-film HFM 2 drops the burn-off. The micromechanical HFM 5 adds return-flow detection and, on most versions, an intake-air temperature sensor. The HFM 7 adds the deflection bypass and is calibrated as a tube plus insert. Part numbers in the 0 280 and 0 281 ranges are Bosch. A neighbouring number is a different curve.

Denso

Denso’s automotive airflow meters are hot wires. Toyota and Lexus are the volume. The element is a platinum wire held a fixed temperature above a thermistor in the same airstream, and the signal on the later sensors is a voltage that rises with mass, inside a 0 to 5 V span. Two packages exist. The earlier one is a measuring tube with the wire in an internal bypass, and on the 1980s performance engines the control unit commands a burn-off after shutdown. The later one is a plug-in slot that samples a passage in the air-cleaner housing or a straight duct, and that slot type has no burn-off relay. Intake-air temperature is commonly a second output in the same plug, with its own ground.

The slot is calibrated for the housing it was designed to sit in. Depth and orientation are part of the calibration. An oiled aftermarket filter is the usual way a Denso wire starts under-reading: the oil film insulates the wire, heater current falls, reported mass falls, and open-loop fuel goes lean. There is no Denso equivalent of the Bosch HFM voltage table on this wiki. Use the curve for the Toyota or Lexus part number. A Bosch column that also spans 0 to 5 V is a different meter.

Hitachi and JECS

Nissan’s ECCS airflow meters of the CA, SR, RB and VG years are hot wires, supplied through JECS and later Hitachi. The early plugs carry a signal that runs about 2 to 7 V, plus a cleaning pin and a calibration pin that the loom often leaves unused. Later plugs are 12 V, ground and signal, and some inserts add intake-air temperature pins that are not connected. The colours and the Consult pins are on Nissan MAF pinouts and Consult.

Hitachi’s other well-known meter is a film. On the GM 3.3 and 3.8 after the 1990 changeover it is a hot film whose output is a high-frequency square wave, about 2.9 kHz at idle and about 5.0 kHz at 3500 rpm on a 3800. That is a different sensor from the Delco film it replaced, which idled near 32 Hz. Both are described under hot-film sensors.

Mitsubishi Electric

Mitsubishi Electric’s meter for the petrol engines of the 1980s and 1990s is a Karman vortex meter with an ultrasonic transmitter and receiver across the wake. The housing can look like any other tube in the intake. Frequency rises with air speed. The measurement is volume, so air temperature is still a separate input. Toyota’s Karman meter is optical, a mirror and a photo-coupler, and is a different sensor.

Siemens VDO and Pierburg

Siemens VDO, later part of Continental, builds hot-film meters. The SIMAF can be programmed for an analogue voltage, a ratiometric voltage or a frequency, with reverse-flow compensation. The 20.3855 is a fixed curve, 8 to 550 kg/h at 12 V. The maf2maf converter remaps that voltage onto an HFM 5 curve and must be powered from a relay, rather than from the control unit’s HFM 5 supply pin.

Pierburg builds both voltage-output and frequency-output films. On the 1.9 TDI the Pierburg analogue meter and the Bosch film share a job and use different curves: idle with EGR closed is about 1.6 V on the Pierburg and about 2.2 V on the Bosch. On the 1.6 HDi and TDCi the Pierburg output is a frequency that falls as flow rises, 5000 Hz with the engine stopped. Those two Pierburg sensors are different parts. Details are on the frequency meter and the TDI measurement pages.

Delphi, Ford and Marelli

Delphi’s predecessors, AC Rochester and Delco, supplied the GM hot-film frequency meters from 1984: about 32 Hz at idle to about 150 Hz at wide-open throttle, idle voltage near 2.5 V if the signal is read as a level. Most GM engines dropped the meter for speed-density in 1990. The Buick 3.3 and 3.8 moved to the Hitachi film above.

Ford’s own early electronic injection used a vane, battery-referenced or 5 V, rising or falling with plate angle. Later Ford mass-air meters are hot wires, usually a sampling element in the inlet tube. Codes 26, 56, 66 and 76 are the out-of-range, too-high, too-low and no-response codes for that Ford signal. The GM frequency codes are a different system.

Magneti Marelli supplied the meters on Fiat-group engines, vanes in the early electronic systems and hot films later. A Marelli film has its own curve. Looking like an HFM 5 does not make it one.

NGK and NTK also supply hot-wire and hot-film elements as original equipment on some Japanese and European engines. The element technology still has to be identified from the part, using the part number, before any voltage or frequency limit from another maker is used.

What stays with the part

  • A 0 to 5 V span. Bosch HFM, later Denso and many Siemens meters all use it, on different curves.
  • A rising frequency. Toyota Karman, Mitsubishi Karman, early Delco film and the Hitachi 3800 all rise with flow, over completely different ranges. The Pierburg diesel frequency falls.
  • A burn-off relay. Present on Bosch LH and early Denso, and brought out, often unused, on early Nissan wires. Absent on HFM films and on later Denso slot sensors.
  • A plug-in insert. HFM 5, HFM 7, Denso slot and PMA1000 are all inserts. Each is calibrated for one housing.