Removed text is struck through; added text is highlighted.
A diesel particulate filter (DPF) warning can result from accumulated soot, interrupted regeneration, a sensor fault or an engine problem producing excess soot. Start with the fault evidence and operating conditions: a warning does not automatically mean the filter needs replacement.
Oxygen-sensor faults and combustion problems may affect aftertreatment diagnosis. See common oxygen sensor faults.Coolant warm-up and its measurement can affect regeneration conditions. See common coolant temperature sensor faults.Crankshaft signal faults are another possible cause of poor running. See common crankshaft position sensor faults. See also Camshaft position sensor faults. See also Throttle position sensor faults. See also Accelerator pedal position sensor faults. See also Knock sensor faults. See also Intake air temperature sensor faults. See also Exhaust gas temperature sensor faults. See also DPF differential pressure sensor faults. See also NOx sensor faults. See also AdBlue and SCR system faults.
Quick symptom guide
What you seeWhere to investigate
DPF warning or restricted powerRead all codes and freeze-frame data; check calculated loading, pressure measurement, regeneration status and related faults.
Regeneration happens frequently or does not finishCheck journey pattern, temperatures, fuel level, sensor plausibility and faults causing excess soot or preventing the process.
Pressure reading implausibleInspect pressure sensor, pipes, ports, wiring and exhaust leaks; compare with vehicle-specific measurements.
Oil level rises or smells of fuelCheck for dilution and follow the manufacturer's service procedure; repeated post-injection and interrupted regenerations are possible causes.
Pressure remains high after a confirmed successful regenerationInvestigate ash, physical restriction, sensor or hose faults and other exhaust restrictions. A single reading does not identify the cause.
Signs overlap with EGR, fuelling and boost problems. Use the handbook for the warning shown and the manufacturer's diagnostic procedure for the exact engine and aftertreatment system.
What the filter is collecting
Sintered-metal diesel particulate filter loaded with soot. The pleated element is a different construction from the square-channel wall-flow monoliths described above. Photo: Michael KR, 1 November 2015, Wikimedia Commons. CC BY-SA 4.0. Longest side reduced to 1,400 pixels for this page; no crop. Adaptations of this photograph must stay under the same licence.
Soot is combustible particulate matter. Regeneration raises filter temperature or uses suitable operating conditions to reduce accumulated soot. Ash is non-combustible residue that accumulates over time and is not removed by normal regeneration. Estimated soot and ash values shown by a scan tool may be calculated rather than directly measured.
Filter constructions vary. The photograph above is a soot-loaded sintered-metal element; many vehicle DPFs use a ceramic wall-flow core. See soot and ash in a DPF for the difference, and HELLA's aftertreatment guide for pressure monitoring and regeneration.
Start with the vehicle, not the filter
Record the complaint. Note the warning, power loss, driving pattern, recent repair work, service history and any failed regeneration attempts.
Save all fault codes and freeze-frame data. Check engine, aftertreatment and relevant other modules. Do this before clearing faults or resetting learned values.
Inspect safely. With components cool, check exhaust joints, wiring, pressure pipes and temperature-sensor connections for visible damage. Look for intake or boost leaks and EGR faults where the evidence points there.
Check oil and fluid requirements. Check oil level and condition against the vehicle procedure. Identify any fuel-borne additive system and follow its service instructions; additive systems and fluid types differ.
Review live data. Record measured differential pressure, engine speed and load, exhaust and coolant temperatures, soot and ash estimates, regeneration status and distance since regeneration where available.
Confirm the measurements. Test pressure sensor and hoses, exhaust-temperature signals and their wiring using the manufacturer's method. Compare pressure at the specified operating conditions and use an independent measurement if the procedure calls for one.
Find the cause. Check for problems preventing regeneration or producing excessive soot, including EGR, charge-air leaks, fuelling and cooling-system faults when supported by evidence.
Choose the repair. Follow the manufacturer's loading thresholds and instructions for normal regeneration, a workshop procedure, professional cleaning or replacement. Retest and complete only the adaptations relevant to the work actually performed.
Differential pressure and sensor faults
The pressure difference across a DPF changes with exhaust flow as well as restriction. Compare readings at the speed, load and temperature specified for that vehicle; a single idle reading or a value from another model is not a universal pass limit. Some systems use different pressure-sensing arrangements, so identify the sensors and ports before testing.
Cracked, blocked, disconnected or incorrectly routed hoses, blocked pressure ports, exhaust leaks and wiring faults can produce a misleading signal. An independent measurement can help separate a sensor fault from an actual restriction when performed at the correct points using the prescribed procedure. HELLA describes a Dacia Dokker example where damaged differential-pressure sensor hoses could distort the value and trigger reduced power.
A plausible pressure sensor does not prove the filter is healthy, and a pressure reading alone cannot reliably distinguish soot from ash or a damaged core. Compare the complete evidence and the vehicle's service limits.
Why regeneration may fail
Frequent short trips or interrupted journeys can stop a normal regeneration from finishing. Depending on the vehicle, a fault code, implausible temperature signal, low coolant temperature, low fuel level or a problem with a required additive system can also prevent it. Excess soot production can overwhelm a working system. The AA's DPF guidance describes several of these factors; exact conditions and warnings depend on the vehicle.
For a warning that the handbook says can be addressed by driving, follow that vehicle's instructions and local road rules. A flashing warning, severe power loss or additional fault may require a workshop diagnosis instead. Do not repeat regeneration attempts to clear a fault without finding why it occurred.
Workshop regeneration
A service regeneration is a controlled workshop procedure, not a universal first step. Before starting, establish that the vehicle, soot loading, oil condition and other prerequisites meet the manufacturer's limits and that relevant faults have been addressed. Excessive loading or a damaged filter can make regeneration inappropriate. Follow the diagnostic tool and manufacturer instructions, including ventilation, surroundings, monitoring and cooling time: the exhaust becomes very hot.
Cleaning or replacing the filter
Cordierite diesel particulate filter after mechanical cleaning. The channel faces are open, with staining left toward the rim. This is not the soot-loaded sintered-metal filter shown earlier. Photo: Michael KR, 1 November 2015, Wikimedia Commons. CC BY-SA 4.0. Longest side reduced to 1,400 pixels for this page; no crop. Adaptations of this photograph must stay under the same licence.
The cleaned filter in this photograph is a cordierite unit, not the same filter or construction as the soot-loaded element shown above. The images are examples, not a before-and-after test result.
If soot cannot be removed by the permitted regeneration procedure, or ash or physical damage is suspected, use the manufacturer's decision process. A specialist can assess whether the specific filter can be cleaned and test it using suitable equipment. Cracked, melted or contaminated cores may require replacement. Compare documented flow or pressure test results before and after cleaning where available; appearance alone does not establish filtering performance.
Do not reset a replacement or ash counter merely to silence a warning. Perform adaptations and counters only when required for the actual repair and according to the vehicle procedure. See particulate filter faults and carbon deposits and cleaning.
An air-mass reading fault can influence combustion or EGR diagnosis. See common MAF sensor faults.Intake MAP and DPF differential pressure are different measurements. See common MAP sensor faults for intake pressure checks.
Check the EGR and turbo systems
An EGR or fuel fault can contribute to excessive soot; a split charge-air pipe or boost-control fault can also cause poor combustion and loss of power. Equally, a DPF pressure-sensor problem or exhaust restriction can resemble an engine or turbo fault. Diagnose each system from measurements rather than assuming one fault proves another.
Common EGR faults covers valve movement, control and flow checks.Turbo diagnostics covers boost pressure and control investigation.Common boost leaks covers charge-air inspection and testing.
For cylinder, fuel-supply and injector checks when fuelling is suspected, see common injector faults.
For fuel-supply and pump diagnosis when fuelling faults are suspected, see common fuel pump faults.
Fuel-pressure sensor diagnosis is covered separately in common fuel pressure sensor faults; it is a different circuit from the DPF differential-pressure sensor.
Verify the repair
Restore all connections, complete required adaptations, then compare relevant readings under the same specified conditions as before. Confirm the original complaint, fault memory and regeneration status over an appropriate test. If the fault returns, reassess sensor plausibility, driving conditions and the underlying cause of soot production before repeating the repair.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Common DPF faults: symptoms, checks and diagnosis
A diesel particulate filter (DPF) warning can result from accumulated soot, interrupted regeneration, a sensor fault or an engine problem producing excess soot. Start with the fault evidence and operating conditions: a warning does not automatically mean the filter needs replacement.
Quick symptom guide
What you see
Where to investigate
DPF warning or restricted power
Read all codes and freeze-frame data; check calculated loading, pressure measurement, regeneration status and related faults.
Regeneration happens frequently or does not finish
Check journey pattern, temperatures, fuel level, sensor plausibility and faults causing excess soot or preventing the process.
Pressure reading implausible
Inspect pressure sensor, pipes, ports, wiring and exhaust leaks; compare with vehicle-specific measurements.
Oil level rises or smells of fuel
Check for dilution and follow the manufacturer's service procedure; repeated post-injection and interrupted regenerations are possible causes.
Pressure remains high after a confirmed successful regeneration
Investigate ash, physical restriction, sensor or hose faults and other exhaust restrictions. A single reading does not identify the cause.
Signs overlap with EGR, fuelling and boost problems. Use the handbook for the warning shown and the manufacturer's diagnostic procedure for the exact engine and aftertreatment system.
What the filter is collecting
Sintered-metal diesel particulate filter loaded with soot. The pleated element is a different construction from the square-channel wall-flow monoliths described above. Photo: Michael KR, 1 November 2015, Wikimedia Commons. CC BY-SA 4.0. Longest side reduced to 1,400 pixels for this page; no crop. Adaptations of this photograph must stay under the same licence.
Soot is combustible particulate matter. Regeneration raises filter temperature or uses suitable operating conditions to reduce accumulated soot. Ash is non-combustible residue that accumulates over time and is not removed by normal regeneration. Estimated soot and ash values shown by a scan tool may be calculated rather than directly measured.
Filter constructions vary. The photograph above is a soot-loaded sintered-metal element; many vehicle DPFs use a ceramic wall-flow core. See soot and ash in a DPF for the difference, and HELLA's aftertreatment guide for pressure monitoring and regeneration.
Start with the vehicle, not the filter
Record the complaint. Note the warning, power loss, driving pattern, recent repair work, service history and any failed regeneration attempts.
Save all fault codes and freeze-frame data. Check engine, aftertreatment and relevant other modules. Do this before clearing faults or resetting learned values.
Inspect safely. With components cool, check exhaust joints, wiring, pressure pipes and temperature-sensor connections for visible damage. Look for intake or boost leaks and EGR faults where the evidence points there.
Check oil and fluid requirements. Check oil level and condition against the vehicle procedure. Identify any fuel-borne additive system and follow its service instructions; additive systems and fluid types differ.
Review live data. Record measured differential pressure, engine speed and load, exhaust and coolant temperatures, soot and ash estimates, regeneration status and distance since regeneration where available.
Confirm the measurements. Test pressure sensor and hoses, exhaust-temperature signals and their wiring using the manufacturer's method. Compare pressure at the specified operating conditions and use an independent measurement if the procedure calls for one.
Find the cause. Check for problems preventing regeneration or producing excessive soot, including EGR, charge-air leaks, fuelling and cooling-system faults when supported by evidence.
Choose the repair. Follow the manufacturer's loading thresholds and instructions for normal regeneration, a workshop procedure, professional cleaning or replacement. Retest and complete only the adaptations relevant to the work actually performed.
Differential pressure and sensor faults
The pressure difference across a DPF changes with exhaust flow as well as restriction. Compare readings at the speed, load and temperature specified for that vehicle; a single idle reading or a value from another model is not a universal pass limit. Some systems use different pressure-sensing arrangements, so identify the sensors and ports before testing.
Cracked, blocked, disconnected or incorrectly routed hoses, blocked pressure ports, exhaust leaks and wiring faults can produce a misleading signal. An independent measurement can help separate a sensor fault from an actual restriction when performed at the correct points using the prescribed procedure. HELLA describes a Dacia Dokker example where damaged differential-pressure sensor hoses could distort the value and trigger reduced power.
A plausible pressure sensor does not prove the filter is healthy, and a pressure reading alone cannot reliably distinguish soot from ash or a damaged core. Compare the complete evidence and the vehicle's service limits.
Why regeneration may fail
Frequent short trips or interrupted journeys can stop a normal regeneration from finishing. Depending on the vehicle, a fault code, implausible temperature signal, low coolant temperature, low fuel level or a problem with a required additive system can also prevent it. Excess soot production can overwhelm a working system. The AA's DPF guidance describes several of these factors; exact conditions and warnings depend on the vehicle.
For a warning that the handbook says can be addressed by driving, follow that vehicle's instructions and local road rules. A flashing warning, severe power loss or additional fault may require a workshop diagnosis instead. Do not repeat regeneration attempts to clear a fault without finding why it occurred.
Workshop regeneration
A service regeneration is a controlled workshop procedure, not a universal first step. Before starting, establish that the vehicle, soot loading, oil condition and other prerequisites meet the manufacturer's limits and that relevant faults have been addressed. Excessive loading or a damaged filter can make regeneration inappropriate. Follow the diagnostic tool and manufacturer instructions, including ventilation, surroundings, monitoring and cooling time: the exhaust becomes very hot.
Cleaning or replacing the filter
Cordierite diesel particulate filter after mechanical cleaning. The channel faces are open, with staining left toward the rim. This is not the soot-loaded sintered-metal filter shown earlier. Photo: Michael KR, 1 November 2015, Wikimedia Commons. CC BY-SA 4.0. Longest side reduced to 1,400 pixels for this page; no crop. Adaptations of this photograph must stay under the same licence.
The cleaned filter in this photograph is a cordierite unit, not the same filter or construction as the soot-loaded element shown above. The images are examples, not a before-and-after test result.
If soot cannot be removed by the permitted regeneration procedure, or ash or physical damage is suspected, use the manufacturer's decision process. A specialist can assess whether the specific filter can be cleaned and test it using suitable equipment. Cracked, melted or contaminated cores may require replacement. Compare documented flow or pressure test results before and after cleaning where available; appearance alone does not establish filtering performance.
Do not reset a replacement or ash counter merely to silence a warning. Perform adaptations and counters only when required for the actual repair and according to the vehicle procedure. See particulate filter faults and carbon deposits and cleaning.
Check the EGR and turbo systems
An EGR or fuel fault can contribute to excessive soot; a split charge-air pipe or boost-control fault can also cause poor combustion and loss of power. Equally, a DPF pressure-sensor problem or exhaust restriction can resemble an engine or turbo fault. Diagnose each system from measurements rather than assuming one fault proves another.
For cylinder, fuel-supply and injector checks when fuelling is suspected, see common injector faults.
For fuel-supply and pump diagnosis when fuelling faults are suspected, see common fuel pump faults.
Verify the repair
Restore all connections, complete required adaptations, then compare relevant readings under the same specified conditions as before. Confirm the original complaint, fault memory and regeneration status over an appropriate test. If the fault returns, reassess sensor plausibility, driving conditions and the underlying cause of soot production before repeating the repair.
Revision 21: Common DPF faults: symptoms, checks and diagnosis
A diesel particulate filter (DPF) warning can result from accumulated soot, interrupted regeneration, a sensor fault or an engine problem producing excess soot. Start with the fault evidence and operating conditions: a warning does not automatically mean the filter needs replacement.
Oxygen-sensor faults and combustion problems may affect aftertreatment diagnosis. See common oxygen sensor faults.
Read all codes and freeze-frame data; check calculated loading, pressure measurement, regeneration status and related faults.
Regeneration happens frequently or does not finish
Check journey pattern, temperatures, fuel level, sensor plausibility and faults causing excess soot or preventing the process.
Pressure reading implausible
Inspect pressure sensor, pipes, ports, wiring and exhaust leaks; compare with vehicle-specific measurements.
Oil level rises or smells of fuel
Check for dilution and follow the manufacturer's service procedure; repeated post-injection and interrupted regenerations are possible causes.
Pressure remains high after a confirmed successful regeneration
Investigate ash, physical restriction, sensor or hose faults and other exhaust restrictions. A single reading does not identify the cause.
Signs overlap with EGR, fuelling and boost problems. Use the handbook for the warning shown and the manufacturer's diagnostic procedure for the exact engine and aftertreatment system.
What the filter is collecting
Sintered-metal diesel particulate filter loaded with soot. The pleated element is a different construction from the square-channel wall-flow monoliths described above. Photo: Michael KR, 1 November 2015, Wikimedia Commons. CC BY-SA 4.0. Longest side reduced to 1,400 pixels for this page; no crop. Adaptations of this photograph must stay under the same licence.
Soot is combustible particulate matter. Regeneration raises filter temperature or uses suitable operating conditions to reduce accumulated soot. Ash is non-combustible residue that accumulates over time and is not removed by normal regeneration. Estimated soot and ash values shown by a scan tool may be calculated rather than directly measured.
Filter constructions vary. The photograph above is a soot-loaded sintered-metal element; many vehicle DPFs use a ceramic wall-flow core. See soot and ash in a DPF for the difference, and HELLA's aftertreatment guide for pressure monitoring and regeneration.
Start with the vehicle, not the filter
Record the complaint. Note the warning, power loss, driving pattern, recent repair work, service history and any failed regeneration attempts.
Save all fault codes and freeze-frame data. Check engine, aftertreatment and relevant other modules. Do this before clearing faults or resetting learned values.
Inspect safely. With components cool, check exhaust joints, wiring, pressure pipes and temperature-sensor connections for visible damage. Look for intake or boost leaks and EGR faults where the evidence points there.
Check oil and fluid requirements. Check oil level and condition against the vehicle procedure. Identify any fuel-borne additive system and follow its service instructions; additive systems and fluid types differ.
Review live data. Record measured differential pressure, engine speed and load, exhaust and coolant temperatures, soot and ash estimates, regeneration status and distance since regeneration where available.
Confirm the measurements. Test pressure sensor and hoses, exhaust-temperature signals and their wiring using the manufacturer's method. Compare pressure at the specified operating conditions and use an independent measurement if the procedure calls for one.
Find the cause. Check for problems preventing regeneration or producing excessive soot, including EGR, charge-air leaks, fuelling and cooling-system faults when supported by evidence.
Choose the repair. Follow the manufacturer's loading thresholds and instructions for normal regeneration, a workshop procedure, professional cleaning or replacement. Retest and complete only the adaptations relevant to the work actually performed.
Differential pressure and sensor faults
The pressure difference across a DPF changes with exhaust flow as well as restriction. Compare readings at the speed, load and temperature specified for that vehicle; a single idle reading or a value from another model is not a universal pass limit. Some systems use different pressure-sensing arrangements, so identify the sensors and ports before testing.
Cracked, blocked, disconnected or incorrectly routed hoses, blocked pressure ports, exhaust leaks and wiring faults can produce a misleading signal. An independent measurement can help separate a sensor fault from an actual restriction when performed at the correct points using the prescribed procedure. HELLA describes a Dacia Dokker example where damaged differential-pressure sensor hoses could distort the value and trigger reduced power.
A plausible pressure sensor does not prove the filter is healthy, and a pressure reading alone cannot reliably distinguish soot from ash or a damaged core. Compare the complete evidence and the vehicle's service limits.
Why regeneration may fail
Frequent short trips or interrupted journeys can stop a normal regeneration from finishing. Depending on the vehicle, a fault code, implausible temperature signal, low coolant temperature, low fuel level or a problem with a required additive system can also prevent it. Excess soot production can overwhelm a working system. The AA's DPF guidance describes several of these factors; exact conditions and warnings depend on the vehicle.
For a warning that the handbook says can be addressed by driving, follow that vehicle's instructions and local road rules. A flashing warning, severe power loss or additional fault may require a workshop diagnosis instead. Do not repeat regeneration attempts to clear a fault without finding why it occurred.
Workshop regeneration
A service regeneration is a controlled workshop procedure, not a universal first step. Before starting, establish that the vehicle, soot loading, oil condition and other prerequisites meet the manufacturer's limits and that relevant faults have been addressed. Excessive loading or a damaged filter can make regeneration inappropriate. Follow the diagnostic tool and manufacturer instructions, including ventilation, surroundings, monitoring and cooling time: the exhaust becomes very hot.
Cleaning or replacing the filter
Cordierite diesel particulate filter after mechanical cleaning. The channel faces are open, with staining left toward the rim. This is not the soot-loaded sintered-metal filter shown earlier. Photo: Michael KR, 1 November 2015, Wikimedia Commons. CC BY-SA 4.0. Longest side reduced to 1,400 pixels for this page; no crop. Adaptations of this photograph must stay under the same licence.
The cleaned filter in this photograph is a cordierite unit, not the same filter or construction as the soot-loaded element shown above. The images are examples, not a before-and-after test result.
If soot cannot be removed by the permitted regeneration procedure, or ash or physical damage is suspected, use the manufacturer's decision process. A specialist can assess whether the specific filter can be cleaned and test it using suitable equipment. Cracked, melted or contaminated cores may require replacement. Compare documented flow or pressure test results before and after cleaning where available; appearance alone does not establish filtering performance.
Do not reset a replacement or ash counter merely to silence a warning. Perform adaptations and counters only when required for the actual repair and according to the vehicle procedure. See particulate filter faults and carbon deposits and cleaning.
An air-mass reading fault can influence combustion or EGR diagnosis. See common MAF sensor faults.
Intake MAP and DPF differential pressure are different measurements. See common MAP sensor faults for intake pressure checks.
Check the EGR and turbo systems
An EGR or fuel fault can contribute to excessive soot; a split charge-air pipe or boost-control fault can also cause poor combustion and loss of power. Equally, a DPF pressure-sensor problem or exhaust restriction can resemble an engine or turbo fault. Diagnose each system from measurements rather than assuming one fault proves another.
For cylinder, fuel-supply and injector checks when fuelling is suspected, see common injector faults.
For fuel-supply and pump diagnosis when fuelling faults are suspected, see common fuel pump faults.
Fuel-pressure sensor diagnosis is covered separately in common fuel pressure sensor faults; it is a different circuit from the DPF differential-pressure sensor.
Verify the repair
Restore all connections, complete required adaptations, then compare relevant readings under the same specified conditions as before. Confirm the original complaint, fault memory and regeneration status over an appropriate test. If the fault returns, reassess sensor plausibility, driving conditions and the underlying cause of soot production before repeating the repair.