The camshaft position sensor (CMP) tells the engine control unit (ECU) about camshaft position. The ECU compares this information with the crankshaft signal to identify engine phase and manage functions such as injection, ignition and variable valve timing. A camshaft fault code does not automatically mean the sensor needs replacing: wiring, its target, mechanical timing and other faults can produce similar symptoms.
Common symptoms and what to check
| Symptom | Useful next checks |
|---|---|
| Long cranking or no start | Check battery and cranking speed, codes, engine speed and crank/cam synchronisation if available. Fuel, ignition and compression are also possible causes. |
| Intermittent stall, hesitation or poor running | Capture the fault under the conditions in which it occurs; inspect sensor wiring, connectors and the signal as well as other engine inputs. |
| Engine warning lamp or reduced performance | Record all codes and freeze-frame data. A circuit or correlation code points to an investigation, not a confirmed faulty component. |
| Fault after timing, cylinder-head or sensor work | Check correct sensor, installation, connector and harness routing; follow the manufacturer’s procedure for timing and target alignment. |
| Fault occurs hot or on vibration | Inspect heat exposure and harness movement, then record supply, ground and signal while safely reproducing the condition. |
Response to a missing CMP signal differs by system: some engines may start after a delay or operate in a fallback mode, while others may not start. HELLA describes starting problems and stored faults; a Pico case study illustrates a delayed-start diagnosis.
Sensor types and common causes
Many CMP sensors use a powered Hall-effect design and produce a switched signal. Others use a different sensing principle, including inductive and AC-excited designs. Identify the actual system from the vehicle’s wiring and service information; connector appearance or number of pins is not a reliable test of sensor type.
- Sensor or target: internal sensor failure, damage, contamination, incorrect mounting or air gap, or a damaged or incorrectly positioned target.
- Wiring and connectors: chafed or oil-contaminated wiring, loose or corroded terminals, a short or open circuit, or loss of the specified supply or ground.
- Crank signal and timing: an implausible crankshaft signal, timing belt or chain issue, incorrect mechanical timing, or a displaced trigger can affect synchronisation.
- Variable valve timing: oil condition or level, an oil-control fault, actuator or mechanical fault may affect camshaft position where applicable. Diagnose the particular engine before attributing a correlation code to any one part.
Pico’s Hall-effect CMP test describes signal testing; its crank/cam comparison explains checking the relationship between the two signals.
Fault codes: what they do and do not say
Generic codes P0340–P0344 commonly concern camshaft position sensor A circuit, range/performance, low, high or intermittent signal. P0016–P0019 concern crankshaft/camshaft position correlation on the indicated bank and sensor. Definitions, available codes and bank or sensor identification must be checked against the manufacturer’s information. A high or low circuit code can result from the sensor, wiring, supply or ECU input; a correlation code can also be mechanical or variable-timing related. See the HELLA OBD code list.
A practical diagnostic sequence
- Record the complaint. Note whether the problem occurs hot, cold, during starting or under load, and whether timing, engine or sensor work preceded it. Save all codes and freeze-frame information before clearing anything.
- Check basics and live data. Verify battery condition and cranking speed. Where supported, watch engine speed and crank/cam synchronisation during the fault. Live data is useful direction, but an RPM reading alone does not prove every pulse is correct.
- Identify the circuit. Find the correct bank and sensor, its sensing principle, wiring diagram, test points and specified voltages. Identify scope grounding and isolation requirements before connecting equipment.
- Inspect with the engine stopped. Check the connector, terminals, harness, mounting and accessible contamination. Inspect the target and sensor clearance where the manufacturer permits; do not disturb timing components unnecessarily.
- Check electrical supply and ground. For a powered sensor, use the manufacturer’s procedure and compare measurements with its specifications, including under load when required. Repair a shared supply or ground fault before condemning a sensor.
- Capture the signal. Use an oscilloscope during cranking or running under the fault conditions, following the correct setup for that sensor. Compare signal shape and voltage with a suitable reference. Check for dropouts and distortion and compare the signal at the sensor and ECU when indicated.
- Investigate timing when indicated. Capture crank and cam signals together and compare with a known-good reference for the exact engine and comparable operating conditions. Follow the vehicle procedure to check mechanical timing, target installation and variable valve timing.
- Repair and prove the result. Correct the identified fault, follow any specified adaptation or relearn procedure, and repeat the original conditions. Confirm synchronisation, starting and fault memory after an appropriate drive or test.
Keep leads, hands and clothing clear of belts, fans and moving parts when cranking or running. If a mechanical timing failure is suspected, stop and follow the manufacturer’s procedure before further cranking. Do not apply a resistance test to a powered or unidentified active sensor; use only the specified test for the identified component.
Understanding crank and cam correlation
A scope can show whether a recognisable cam signal reaches the ECU and where its transitions occur relative to the crank signal. An electrical dropout and an otherwise clean but incorrectly phased signal suggest different lines of investigation; neither pattern alone identifies the failed part. Compare the same reference features and operating conditions against the correct known-good capture. Variable valve timing can change the relationship, so account for commanded and actual cam position and the manufacturer’s test conditions.
For example, a good signal at the sensor but a missing signal at the ECU directs attention to the intervening circuit and connections. Two clean signals with an unexpected relationship call for checks of the reference, variable timing operation, trigger attachment and mechanical timing. A low battery or slow cranking may complicate both checks.
Replacement and verification
Fit the specified sensor and seal, check the mounting surface and routing, and observe the manufacturer’s torque, clearance and fitting instructions. Similar-looking sensors are not necessarily interchangeable. Carry out any required relearn only where specified. Verify the repair under the original hot, cold or intermittent conditions and check for returning faults; if symptoms remain, revisit the evidence instead of replacing further parts by guesswork.
Related diagnostic guides
- AdBlue and SCR system faults — fluid supply, dosing and SCR efficiency checks.
- NOx sensor faults — NOx measurement, wiring and SCR checks.
- DPF differential pressure sensor faults — pressure hoses, sensor readings and filter restriction.
- Exhaust gas temperature sensor faults — exhaust temperature, wiring and regeneration checks.
- Intake air temperature sensor faults — air temperature, wiring and heat-soak checks.
- Knock sensor faults — knock sensing, wiring and combustion checks.
- Accelerator pedal position sensor faults — pedal input and acceleration response checks.
- Throttle position sensor faults — throttle feedback and response checks.
- Crankshaft position sensor faults
- Coolant temperature sensor faults
- Oxygen sensor faults
- MAP sensor faults
- MAF sensor faults
- Fuel pressure sensor faults
- Fuel pump faults
- Injector faults
- DPF faults
- EGR faults
- Turbo diagnostics
- Boost leaks