Applicability: Engineering names below are examples from the community SC8S5031 Simos 18.1 reference unless another source is identified. Confirm the exact ECU software, definition, units, axes, indexing and installed hardware before using a calibration; names and meanings cannot be assumed across variants. The community cross-reference can contain extraction or indexing errors. SC8S5031 reference.
Characterise the installed injector
Use injector-specific flow and timing data, including fuel, test pressure, battery voltage and short-pulse behaviour. Compare pressures as a differential across the injector, and verify the regulator and pressure-sensor arrangement on the actual installation. Injector flow and dead time vary with the operating conditions; generic data from another ECU or injector should not be transplanted. The following supplier explanations are general injector background, not Simos-specific map definitions: Haltech dead time and short-pulse nonlinearity.
Example OEM calibration names
ip_fac_mff_ti_stnd_h_rng_mpi[0]: inverse injector characteristic relating requested port fuel mass to injection time, expressed in ms per mg/stroke in this example. The displayed axis isfac_afu_ratio, a fuel-mixture factor; the extracted reference shows one axis point for this entry even though its general narrative discusses multiple fuels. Confirm the active fuel configuration, axis data and indexing in the matched software; the factor alone is not a short-pulse or voltage correction. INJR final MPI timing.ip_ti_add_dly_mpi[0]: voltage-dependent injector delay correction in milliseconds.ip_ti_add_dly_temp_cor_mpiadds a temperature-related correction; the example uses intake-manifold temperature and predicted cylinder air mass. INJR dead-time correction.ip_fac_cor_ti_1_hom_clc_mpi: a cylinder-individual nonlinearity correction between calculated injection time and requested fuel mass. Its axis is in mg/stroke, but the extraction marks the runtime inputNO_INPUT_QUANTITY; confirm the actual input, indexing and correction convention before interpreting it. INJR final MPI timing.ip_fac_ti_prs_mpi: injector-time correction factor against injector differential pressure. In this exampleprs_dec_inj_1_hom_mpiis a runtime quantity calculated asFUP_MPI − MAP, not an independently measured differential-pressure sensor or editable map. Confirm the source and reference of each input and verify actual rail and manifold pressures on the vehicle. INJR pressure correction.ip_fac_ti_temp_cor_mpi: fuel-temperature correction versustfu_mpi; determine whether the matching signal is measured or modelled. INJR MPI fuel-temperature correction.ip_ti_min_mpi[0]: minimum injection-time calibration in the published example. Its displayed axis and extracted narrative disagree about voltage versus pressure difference, so verify the matching A2L and software before assigning an axis. INJR final MPI timing.
Flow scaling and test conditions
In its EA888 Mk7 MPI guide, EcuTek describes scaling its MPI injection-time-to-fuel-flow factor by original injector flow divided by replacement injector flow. The guide identifies example values of 200 cc/min and 0.434 ms/(mg/stroke) for its 280–310 PS EU application, and 175 cc/min and 0.416 ms/(mg/stroke) for a different 220–230 PS EU application. These are product- and example-specific reference values, not an authoritative stock identification for every engine. Read the actual starting calibration, verify injector identity and compare ratings measured with the same fluid, pressure differential and test conditions.
For arithmetic only, if a confirmed 200 cc/min injector and a replacement rated 400 cc/min use the same measurement basis, the EcuTek ratio is 200/400 = 0.5: an example factor of 0.434 becomes 0.217 ms/(mg/stroke). This illustrates inverse scaling, not a validated setting, actual fitted injector, or complete calibration. EcuTek separately calls for injector-specific voltage latency and minimum injection-time data, and identifies Mass Fuel Flow Reference Delta as a monitor for the reference-flow offset. Map selection, pressure, fuel properties, short-pulse behaviour, engine hardware and ECU software still require independent validation.
Bosch Motorsport's injector background gives a square-root relationship for estimating static flow at a changed pressure. In a simplified comparison with the same fuel and injector, static flow at pressure differential 2 is approximately static flow at differential 1 multiplied by the square root of differential 2 divided by differential 1. Use pressure across the injector, not uncorrected gauge rail pressure; check limits and verify actual flow. This approximation does not account for short-pulse nonlinearity, temperature, driver characteristics or fuel-density changes. Bosch's EV 14 product information lists varied flow, spray, length and connector versions, so “EV14” alone is not enough to select calibration data or establish fitment.
Worked example: MPI transition deviation
A Simos 18.1 port-injection report describes a brief lean lambda deviation and rpm change when MPI first became active. The spike was later reported as almost gone after the injector dead-time data was corrected, although some correction remained. A hybrid turbo and other calibration changes were also involved; the account is not a controlled before-and-after test, and injector hardware and exact software were not fully established. It illustrates recording lambda target and actual, battery voltage, DI/MPI mode and pulse times through a repeatable transition, rather than assuming a single injector constant resolves every mixture deviation. The forced-mode tests suggested in that report depend on the calibration and hardware and are not a universal instruction to disable protections.
Practical verification
Check idle, short pulses, voltage changes, warm-up and the transition into port injection as well as high-load flow. Compare requested fuel, lambda target, measured lambda and trims with differential pressure and pulse width. Log requested, calculated and performed injection signals when available; their names and sampling must match the software. For example ti_2_mes_mpi[3] is an example ECU-reported performed time for a second or additional MPI pulse for a specified cylinder; a zero can reflect an inactive pulse or unavailable channel and is not by itself proof that all MPI delivery stopped. INJR transfer to basic software.
Do not interpret a software maximum pulse-time value as proof of physical injector or fuel-system capacity. Diagnose pressure, actual injection window, fuel demand and lambda together.
For port-injection end-angle maps, cam correction and transient phasing, see Simos 18 MPI injection timing and phasing.
Related: Fuel system and MPI upgrades · MPI combustion modes and fuel split · MPI injector calibration · Direct injection and fuel pressure · Ethanol and flex fuel.