Scope: Calibration names and signal descriptions here are examples from the community SC8S5031_C_OEM Simos 18.1 cross-reference. Verify ECU hardware, software, A2L, scaling, units, axes and activation on the target. An extracted description can be incomplete or mismatched; names do not establish that any function is active in another image. The ECU adaptation and statistical indicators discussed here do not directly measure the petrol's laboratory octane rating.
Fuel, octane and calibration
Octane rating indicates fuel resistance to knock under specified laboratory test conditions. RON and MON use different test conditions; the common US anti-knock index (AKI) is (RON + MON) / 2. A number on a pump and a tune's fuel requirement must use the same rating system; there is no exact universal RON-to-AKI conversion without the fuel's MON. Fuel composition and ethanol content are separate considerations. US DOE/NREL fuel assessment; Worldwide Fuel Charter.
Use the fuel specification required by the actual calibration. COBB's MQB flex-fuel release, for example, specifies separate 91 and 93 octane base-fuel maps in its own application even with an ethanol sensor. Ethanol percentage is not a direct measurement of the base petrol's knock resistance. Higher displayed ethanol or a selected map slot does not establish that the fuel meets every requirement.
Knock-based global adaptation
The community KNCK global adaptation description describes a mean of individual adaptation corrections feeding a global factor and a global ignition correction. Its narrative associates an increasing factor with poorer fuel quality and describes recovery when mean correction is sufficiently small. This is a response to knock-related behaviour under the conditions in which learning is enabled, not a laboratory RON reading. Temperature, load, calibration, noise, mechanical condition and detection availability can all complicate interpretation.
fac_ad_knkis the global adaptation factor;iga_ad_knkis the resulting global ignition-angle correction, not an editable ignition table.lv_fac_ad_knk_enais the global-adaptation enable flag;lv_fac_ad_knk_limindicates a limitation. Logger names, sign convention, indices and availability require verification. KNCK control reference.ip_fac_ad_knk_incandip_fac_ad_knk_decdescribe global-factor increment and decrement curves versus engine speed.ip_cycnr_ad_knk_incandip_cycnr_ad_knk_decdescribe combustion-cycle counts for global-factor changes, also versus speed in this definition.ip_fac_ad_knk_maxis described as a threshold for recognising factor 1 over the drive cycle, with coolant and modelled cylinder-intake-air temperature axes. It should not be assumed to be an octane number or a simple high-octane timing map.- For the separate individual AD1 loop,
ip_iga_ad_1_thd_dec_knkandip_iga_ad_1_thd_inc_knkare spark-retard thresholds for adaptation in retard and advance directions, respectively, versus engine speed.iga_ad_1_knk[3]is an example runtime individual-adaptation signal. Confirm the cylinder/index mapping on the target.
These are monitoring and adaptation mechanisms. Suppressing them merely to remove visible correction can conceal a real combustion problem. Compare per-cylinder fast retard, individual learned corrections, the global correction and the enable state rather than treating them as one quantity.
Operating-point learning and key-cycle persistence
The SC8S5031 KNCK control reference identifies id_iga_ad_1_knk_len as the AD1 learning-grid definition and iga_ad_1_knk_save[3] as an example cylinder-indexed saved-adaptation table. Its displayed operating-point axes use n_knk in rpm and maf_h_rng_knk in mg/stroke. The narrative describes applying the relevant previously saved correction when the working point changes, then continuing AD1 correction. The table is learned state, not a base ignition table or an octane map; confirm axis layout, index-to-cylinder mapping and memory representation on the actual ECU.
ip_fac_tco_knk_ad is described as a coolant-temperature weighting factor for AD1 and global adaptation, with tco in °C as its axis. In the same reference, AD1 maps are stored in non-volatile memory during power-latch, while the global factor may be modified according to conditions before storage. The extraction describes lc_knk_ad_clr as a calibration switch that clears several learned values before storage. Do not assume every key cycle, battery disconnect, flash or scan-tool reset clears or preserves the same values: the implementation, memory state, reset procedure and tool matter. Record adaptation state and repeat comparable tests rather than interpreting a single post-restart trace as a fuel-octane measurement.
Low-RON statistical detection examples
The FUSL reference describes a low-RON symptom/state strategy in this image. Its indicators are inferred states with operating conditions and timers, not a fuel sample test. Related names include:
ip_iga_thd_low_ron: ignition-angle threshold for symptoms of low-RON fuel, against engine speed and predicted cylinder air mass.ip_iga_hys_rls_ron_det: ignition-angle offset for releasing low-RON states, against engine speed and predicted cylinder air mass.ip_fac_iga_thd_low_ron_cor: a correction factor with engine speed and intake-air temperature axes;id_maf_min_low_ron_enais an engine-speed-dependent air-mass threshold for detection activation.state_cdn_ron_detis a runtime state-transition condition; the reference describes values for holding, advancing or releasing a state. It is not a numerical octane measurement.lv_low_ron_det_enais a separate detection-enable flag in the fuel-quality adaptation reference, which lists additional conditions including knock-detection availability and coolant temperature.
Check the precise selectors, signals and implementation. The existence of a detection threshold does not prove fuel below a particular pump grade, nor that every operating mode continuously evaluates it.
Aftermarket octane sliders and logging
The community Simos Wiki custom-features description describes Eurodyne's custom octane slider as interpolating between two repurposed basic-ignition tables. This is a product-specific feature, not proof that all factory Simos 18 calibrations use the same high/low octane tables or automatically sense the selected fuel. Verify installed software and the tuner's map documentation. THANAS's Simos 18 switchable-map example likewise lists fuel-specific map slots as examples, with individual calibration.
For diagnosis record the fuel source and grade, rating system, measured ethanol content if relevant, software and selected mode. Compare repeatable, equivalent operating points while logging engine speed, load or air mass, actual and target lambda, intake and coolant temperatures, ignition table output and final timing, cylinder-specific knock corrections and available adaptation state. Note detection enable, interventions and logger sampling. COBB's MQB monitor list documents examples of final ignition, temperature correction and per-cylinder knock channels for its supported vehicles.
A persistent change can have other causes besides the fuel grade; investigate hardware, fuel delivery, sensors and calibration before assigning one cause. A quiet log alone does not prove adequate knock margin. Avoid assuming an immediate adaptation reset or a universal number of miles for relearning.
Related: fuel octane · Simos 18 knock detection and control · ignition timing · ethanol and flex fuel · switchable maps.
For pre-spark combustion, low-speed high-load research and diagnostic limits, see Simos 18 low-speed pre-ignition and knock.