Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Applicability: Engineering names below are examples from the community SC8S5031 Simos 18.1 reference unless another source is identified. Confirm the exact ECU software, definition, units, axes, indexing and installed hardware before using a calibration; names and meanings cannot be assumed across variants. The community cross-reference can contain extraction or indexing errors. SC8S5031 reference.

Pressure control and diagnosis

Direct injection depends on the low-pressure supply as well as the high-pressure pump, rail, injector flow and available injection window. Compare the requested and measured values at the appropriate locations rather than assuming a high-pressure shortfall is always the HPFP. Pressure units, signal sampling and whether a signal is measured or modelled must be checked for the actual ECU and logger.

In the published FUSL fuel-pressure setpoint calculation, ip_fup_sp_bas_sel[12] is one example base setpoint selection indexed by engine speed and predicted air mass. idx_fup_sp_sel_cmb_mod is a runtime selection signal; fup_sp_tmp, fup_sp_lim, fup_sp_max, and lv_fup_sp_grd_act describe stages or states of setpoint calculation, not maps to edit. The array index is not a universal selection. A low final command and a commanded pressure that hardware cannot achieve require different investigations.

The SC8S5031 measured-value reference lists fup_efp_mes and fup_efp_sp for feed-pressure measurement and electrical-pump setpoint, fup_h for high-range pressure, fup_dif for high-side deviation, and pump_vol_vcv and state_vcv for pump-control information. These are diagnostic signals; establish their definitions, pressure reference and logger units for the vehicle. None alone establishes pump headroom.

Injection window and pulse constraints

At high demand, injection must fit in the available crank-angle window as well as satisfy pressure and fuel-mass requirements. The INJR injection-phase reference identifies ip_eoi_lim_ofs_iga as an end-of-injection limit offset associated with ignition and combustion mode. lv_crk_dif_soi_eoi_lim, its _mpi counterpart, and lv_crk_inj_rng_lim are runtime range-related signals. The injection-phase calculation also describes lf_inj_rng_sho_not_suf[0][0] for an insufficient shortened injection range and c_delta_t_min_dui_4 for pulse separation. Confirm the matching definition and cross-reference; these indicators do not independently identify every cause of a fueling problem. Do not remove phase limits to conceal inadequate hardware.

Lambda request is coordinated

ip_lamb_fl_sp is a full-load lambda setpoint candidate indexed by rpm and elapsed full-load time in the published example; ip_lamb_fl_sp_tia is a temperature-related candidate. lv_tia_cdn_fl_sp is a runtime condition. These are not necessarily the final commanded lambda because other conditions, protections or installed tuning features can alter the request. TQDR full-load enrichment; EcuTek RaceROM EA888 documentation.

For a turbo or fueling upgrade, log final lambda target and measurement, low- and high-side pressure setpoints and actuals, available pump-control signals, injector time, combustion mode and relevant phase-limit states across a controlled range of load and engine speed. Include warm-up and transients rather than treating a single full-load pull as complete validation.

Mixture feedback guides: lambda control · fuel trim and adaptation.

For SOI, EOI, pulse separation and injection-window examples, see Simos 18 direct injection timing and phasing.

For low-side pressure, pump duty and upgraded pump control, see Simos 18 low pressure fuel pump control and upgrades.

For pump displacement modelling, VCV control and upgrade checks, see Simos 18 high pressure fuel pump control and upgrades.

Related: Fuel system and MPI upgrades · MPI combustion modes and fuel split · MPI injector calibration · Direct injection and fuel pressure · Ethanol and flex fuel.

For direct-injector fuel-mass/time characterisation, current-profile maps and COSI feedback examples, see Simos 18 direct injector characterisation and COSI.

For rail-pressure sensor conversion, validity flags, substitute readings and diagnostic-monitoring examples, see Simos 18 fuel pressure sensor and diagnostic monitoring.