Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Fuel-system decisions

Scope: These are EA888 Simos 18 examples, mainly 18.1. Exact ECU hardware, engine, transmission, software, calibration and patches determine whether a function or definition applies. Community labels are research leads: confirm the target A2L, axes, units, scaling, selectors and logs. Neither listed names nor file ranges are recommended settings.

Extra air and ethanol can increase fuel demand. Depending on the engine and market, the hardware may have direct injection alone or both direct and port injection. An HPFP upgrade, a low-pressure pump change and MPI injectors address different limits; none guarantees adequate fuel delivery or a correctly calibrated engine. See the Simos 18 fuel-upgrade discussion and Simos Wiki fuel-management overview for community examples.

Inventory both pumps, pressure sensors, rail routing, injectors and control hardware. Compare low-side and direct-injection rail pressure with their respective targets under appropriate load. The location of the pressure sensor matters: a dual-injection thread reports a pressure drop between feed and port rail in one layout. Do not assume every retrofit or factory circuit is plumbed the same way.

MPI and combustion modes

Port injection needs the physical injectors and compatible driver, wiring and fuel supply, plus a software strategy that requests it in the actual operating mode. Simos Wiki describes combustion-mode selection and its relationship to DI/MPI operation. A commanded pulse alone does not prove correct injection, spray or lambda. Characterise the actual injectors and verify idle, warmup, transient and load operation.

Map and signal examples

The following are from the SC8S5031_C_OEM community A2L cross-reference, not universal ECU identifiers:

  • ip_fac_mff_ti_stnd_h_rng_mpi[0] — an MPI injector characteristic relating fuel mass to injection time in the final injection timing reference. Fuel blend and injector characteristics matter.
  • ip_fac_ti_prs_mpi — pressure-difference correction to injection time; prs_dec_inj_1_hom_mpi is a runtime pressure-difference measurement in the MPI pressure-correction reference.
  • ip_fac_mff_bas_mplh[4] — a multiple-injection fuel-mass correction entry, not a DI/MPI split map. The multiple-injection reference also lists a combustion-mode selector id_idx_cal_fac_mff_bas_mplh.
  • ip_ti_min_mpi[0] is listed as minimum MPI injection time and lv_ti_lim_max_mpi as a measurement flag. The community index's minimum-time axis descriptions conflict, so confirm them in the matching A2L rather than inferring a correction.

High-load pressure and injection phase

In the SC8S5031 fuel-pressure setpoint cross-reference, ip_fup_sp_bas_sel is a family of basic fuel-pressure setpoint tables. The displayed example has engine speed and predicted cylinder air mass axes, with a pressure output; idx_fup_sp_sel_cmb_mod is a runtime selector, not a calibration map. Confirm the selected combustion mode and actual pressure reference in the matching ASW. Increasing a target cannot establish that a pump, sensor, injector or supply line can achieve it.

The SC8S5031 injection-phase reference describes ip_soi_1_opp_1_cus as start of injection for the first pulse during single injection, and ip_soi_1_opp_2_cus for the first pulse during double injection. The cited examples use predicted cylinder air mass and injection speed as axes; their outputs are crank angles. These are mode-specific phase entries, not interchangeable fuel quantity maps. Check the selected injection mode, pressure and actual injection duration before drawing conclusions about the usable window.

An injector flow-test discussion contains disputed assumptions about direct-injection timing windows and flow. A pump upgrade alone does not establish injector headroom: examine injection timing/window, supply and rail pressures, lambda, trims and the actual injection mode together.

Detailed fuelling guides: MPI combustion modes and fuel split · MPI injector calibration · direct injection and fuel pressure.

Related guides: bigger turbos · wastegate and boost control · fuel-system and MPI upgrades · ethanol and flex fuel · torque model and DSG · ignition and knock · launch control · rolling anti-lag.

References reviewed 17 November 2026. Forum accounts are reported observations, not independently verified fixes.