Tuning Wiki

ZF 6HP is a family of six-speed torque-converter automatic transmissions. A complete type, suffix and parts-list number identify the particular gearbox more accurately than “ZF6”; the mechanical assembly, mechatronic hardware and vehicle software must be matched separately. See ZF's 6-speed family tree and identification guide and remanufactured transmission catalogue.

Cutaway of ZF 6HP26 automatic transmission
ZF 6HP26 cutaway. Photograph by Ralf Pfeifer, Wikimedia Commons, CC BY-SA 3.0; unmodified.

Types and identification

ZF's dated family-tree document groups its 6HP19, 26 and 32 rear-wheel-drive families and documents 6HP21 and 6HP28 developments and four-wheel-drive variants. These descriptions are from that source, not a guarantee that a unit with the same broad name fits a particular vehicle.

TypeConfiguration in ZF's 2009 guideIdentification note
6HP19Rear-wheel driveZF also lists 6HP19X external 4x4 and 6HP19A internal 4x4.
6HP21 / 21XRear-wheel drive / external 4x4Distinct types in the 19-family branch; check the complete part number.
6HP26 / 26X / 26A61Rear-wheel drive / external 4x4 / internal 4x4Case, output and application differ; suffix matters.
6HP28 / 28X / 28A61 / 28AFRear-wheel drive / external 4x4 / internal 4x4 variantsZF identifies these separately within its 26/28 branch.
6HP32 / 32X / 32ARear-wheel drive / external 4x4 / internal 4x4Match the actual gearbox and assembly number before ordering.

Source: ZF 6 Speed Family Tree, revision 1.2. ZF separately lists the 6HP19, 19X, 19A, 21, 21X, 26, 26A61, 26X, 28, 28A61, 28AF, 28X, 32 and 32A in its 6HP seal-kit information. These are examples, not a complete model or application list. Do not infer a certified torque limit from the digits in the name.

Record the full ZF main parts-list / specification number, transmission part number and serial number, plus OE number, donor vehicle, engine, date and driveline. ZF's identification figure also shows an OE control-module hardware number where fitted. A code on a vehicle listing or an apparently similar casting is not enough to identify interchangeability.

Individual 6HP controller guides

Some connector tables are sourced application examples, not verified for every part number. Follow the exact vehicle and controller documentation.

Mechatronics and factory controller

In BMW's documented E65 GA6HP26Z application, the electronic transmission control and hydraulic valve body form a mechatronic unit inside the transmission. BMW's E65 training describes three on/off solenoids and six electronic pressure-control valves, while its E70 GA6HP19TU/26TU training lists two on/off and seven proportional pressure-control valves. Those counts and selector arrangements apply to the stated examples only; do not infer a universal 6HP solenoid assignment. Sources: BMW E65 GA6HP26Z training and BMW E70 transmission training.

Record the mechatronic label and electronically read controller hardware and software identifiers, not just the gearbox name. Factory EGS / TCM software, immobiliser pairing, selector type and engine torque coordination depend on the donor. BMW's EWS4 service bulletin describes matched EGS, engine and CAS modules for the affected BMW vehicles; it must not be applied to all 6HP vehicles. No universal connector pinout is asserted here: use the vehicle, TCU and connector-specific diagram and view orientation.

For a conversion, check bellhousing, converter, crank/flexplate interface, cooling, mount, length, output flange or transfer case, selector and park actuation, speed signals and engine torque reduction on the exact donor and recipient. See ZF 6HP and 8HP tuning and swap diagnosis.

Programming and swap-control examples

These are supplier-documented examples, not evidence that a tool works with every 6HP. Verify transmission and controller IDs, operation, method, licence, harness, power and recovery procedure before use. Read/write access and calibration editing are different functions.

  • xHP Flashtool: xAutomotive documents settings for supported six-speed ZF applications; use its vehicle checker for the specific car and controller.
  • AutoTuner: the supplier lists ZF 6HP MPC562 OBD read/write; check the exact vehicle and available function.
  • Alientech KESS3: Alientech's upgrade 3.42 documents bench read, write and cloning for Foton Sauvana 2.0T 6HP19 applications from 2014. This example does not establish BMW or other applications.
  • Magicmotorsport FLEX: the manufacturer's duplicable-unit list lists bench 6HP duplication and specific restrictions. Duplication is not itself a tuning map or proof of a particular calibration-write protocol.
  • CANformance CANTCU: its transmission matrix lists beta integrations for BMW E-series 6HP19/26 mechanical-selector and 6HP21/28 joystick-selector cases. This integrates a retained transmission TCM; support, shifter and flasher limitations differ from its 8HP entries.

Service and diagnosis

Use the fluid, parts and fill procedure for the complete type and specification. ZF service information 50145 identifies different procedures and fluid requirements by application; do not assume every 6HP uses the same fluid or level procedure. Inspect leakage, cooler and connector seals, fault codes and transmission oil condition before attributing a complaint to software.

Log requested and actual gear/range, relevant engine and shaft speeds, converter command/slip, temperature, throttle and torque intervention where supported. Save the original fault information and adaptations before changes. Adaptation cannot repair mechanical, electrical or hydraulic faults. For detailed application-specific checks see BMW E65/E70 6HP diagnosis and Maserati M145 6HP26 diagnosis.

Related: ZF gearbox overview, ZF 8HP gearbox types. Sources reviewed 17 November 2026.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.