Tuning Wiki

The GS19.02 is an electronic transmission controller used in certain ZF 6HP26 mechatronic assemblies. In a Jaguar 6HP26, the TCM sits on the hydraulic valve body and connects to the vehicle through a 16-way transmission connector; it uses speed, selector, engine and vehicle information to control shifts. Jaguar 2004-model-year 6HP26 on-board-diagnostics description.

ZF 6HP26 transmission cutaway
ZF 6HP26 transmission cutaway, shown for family context; it does not identify the installed TCM. Ralf Pfeifer, Wikimedia Commons, CC BY-SA 3.0, unmodified.
ZF 6HP mechatronic electronic module and connector sleeve
Illustrative ZF 6HP mechatronic electronic module and connector sleeve, from ZF Aftermarket service information 50324. Credit ZF Friedrichshafen AG; reproduced with user-confirmed permission. This general image does not identify the controller part number or a Jaguar-specific unit.

Identification and compatibility

Jaguar specialist Old Jaguar's 6HP part-number guide associates GS19.02 mechanical-shift 6HP26 units with Jaguar S-Type X202, XJ X350 and XK X103 and cites Bosch 0260550001 or 0260550011 and ZF 0501213094 or 0501213414. This is a specialist's application list, not a ZF interchange approval: check the actual plate, control unit hardware/software and vehicle VIN, engine, selector and market. The same Bosch hardware number found on a different vehicle is not proof the software or assembly is suitable. The separate 6HP family guide covers mechanical variants.

Jaguar 6HP26 16-way connector example

The following functions transcribe the Jaguar 6HP26 pin-assignment table in William Henney's ZF6HP26 training presentation. It lists an example with M-shift and touch-shift signals; the source does not tie the table to the Bosch part numbers above or a VIN. It shows a numbered connector photograph but does not unambiguously state the view orientation: match the manufacturer drawing and moulded cavity numbers with the vehicle-specific wiring document before making connections. “Not used” means that source example only. These are source-documented assignments, not independent bench verification.

CavityFunction in cited example
1M shift program
2CAN low
3ISO K (listed as example application)
4Touch −, manual downshift
5Touch +, manual upshift
6CAN high
7Not used in source example
8Not used in source example
9Terminal 15 wake-up
10P/N signal, starter inhibit
11Not used in source example
12Not used in source example
13Terminal 31-1 ground
14Terminal 30 permanent positive
15Not used in source example
16Terminal 31-2 ground

Do not apply the table to Jaguar 6HP26/28 shift-by-wire, Land Rover or BMW modules without their specific documentation. The presentation shows a different shift-by-wire example with LIN at cavity 8. Obtain the correct fuse, power sequencing and termination requirements; never infer them from a family name.

Factory programming and calibration tools

Jaguar's 2004 model-year document describes vehicle diagnosis. Jaguar technical training reproduced by Manualzz states that replacement mechatronics in its documented 6HP26 application require programming with WDS and an adaptation drive. This is service configuration, not by itself a custom tuning capability.

PCMflash lists a Jaguar/Land Rover transmission module with 6HP26/6HP28 read, write and checksum capabilities; its module 81 manual gives the protocol family. Identify the specific vehicle and controller and check the supplier's current connection method and function list. Magicmotorsport FLEX lists 6HP bench duplication in its compatibility table; duplication is not evidence of calibration editing for this particular hardware ID. Original-file recovery and stable power are essential; tools and appropriate calibration software are separate.

See ZF gearbox and transmission control. Sources reviewed 17 November 2026.

Community replacement reports

In an April 2021 Jaguar Forums discussion, an S-Type R owner reports an unsuccessful TCM flash and considers a used S-Type mechatronic rather than an unknown Ford or BMW donor. The thread describes a proposed replacement, not a verified completed fit, and does not identify the GS19.02 hardware number. It illustrates the need to check the exact part, software and recovery route, not that matching the broad gearbox name guarantees interchange.

In a separate repair-shop discussion, a contributor recounts difficulty locating equipment able to program a Jaguar replacement mechatronic's shift strategy. The specific controller number and independent outcome are not established, so confirm equipment and programming support for the actual vehicle before removal.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.