GS19.04 is a controller designation used in selected Bosch/ZF 6HP26 mechatronics. Its shift-by-wire version must be distinguished from similarly designated mechanical-shift versions.


Identification and examples
Jaguar specialist Old Jaguar associates the 6HP26 GS19.04 E-shift example with Bosch 0260550024 and ZF 6058007071, and lists Jaguar XF X250 2.7, 3.0 and 4.2 and Aston Martin DB9 examples. Its separate GS19.04 M-shift entry has different identifiers. This is a specialist reference, not a guaranteed interchange list; confirm the actual gearbox, TCM hardware and software, donor, selector, engine, VIN and market.
The transmission controller and hydraulic valve body form the mechatronic in Jaguar's documented 6HP application; see the Jaguar 6HP26 diagnostic description. Vehicle configuration and selector arrangements vary by model.
Jaguar 6HP26/28 shift-by-wire connector example
The 16-way gearbox connector assignments below are transcribed from William Henney's 6HP26 training presentation, specifically its “Jaguar 6HP26/28 with shift-by-wire” table. The presentation does not associate the table with a specific Bosch number or VIN and does not clearly state connector-face orientation. It gives a numbered connector photograph: check that and the actual VIN-specific wiring document and moulded cavity numbers before connecting. These are documented assignments for the described example, not independently bench-verified or a guaranteed pinout for this particular controller number. “Not used” applies to the source example only.
| Cavity | Function in source example |
|---|---|
| 1 | Not used in source example |
| 2 | CAN low |
| 3 | ISO K (example application) |
| 4 | Not used in source example |
| 5 | Not used in source example |
| 6 | CAN high |
| 7 | Not used in source example |
| 8 | LIN selector-position information |
| 9 | Terminal 15 wake-up |
| 10 | Park / no-park signal |
| 11 | Not used in source example |
| 12 | Not used in source example |
| 13 | Terminal 31-1 ground |
| 14 | Terminal 30 permanent positive |
| 15 | Not used in source example |
| 16 | Terminal 31-2 ground |
The same presentation's mechanical-selector example has different functions at cavities 1, 4, 5 and 8. Do not transfer these values to mechanical-shift Jaguar, Land Rover, BMW or another car without its own wiring evidence.
Programming and recalibration
PCMflash lists Jaguar/Land Rover 6HP26/28 in module 81's manual, with reading, writing and checksum for specific TCM families. Magicmotorsport FLEX lists selected 6HP bench duplication in its duplicable units list; duplication alone does not prove calibration editing for this exact number. Check the current tool's vehicle, ECU identity, protocol and required licence. A calibration editor or service is separate from the device that reads and writes a file.
Use manufacturer-prescribed service configuration and a recovery plan when replacing the TCM. A compatible blank or used controller may require application-specific software and setup; match the vehicle and preserve its original identification and configuration before changing anything.
See ZF 6HP gearbox types and controllers. Sources reviewed 17 November 2026.
Community fitting and service experience
In a Jaguar XF six-speed service report, an owner describes difficulty reaching the electrical connector sleeve and notes that the seal tubes in the larger 6HP26/28 family differ from 6HP19/21. The report does not identify GS19.04 or document a controller swap; use it as an access and parts-identification example, not a pinout or replacement guide.
Jaguar's JTB00305NAS1, shared on that forum, identifies selected 2009–2011 XF 6HP26 vehicles and VIN ranges for a transmission MIL issue. Check the actual VIN and bulletin before applying any procedure; the bulletin does not identify every unit as Bosch 0260550024.