Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Changes from revision 4 to revision 5

Removed text is struck through; added text is highlighted.

Applicability: Engineering names below are examples from the community SC8S5031 Simos 18.1 reference unless another source is identified. Confirm the exact ECU software, definition, units, axes, indexing and installed hardware before using a calibration; names and meanings cannot be assumed across variants. The community cross-reference can contain extraction or indexing errors. SC8S5031 reference.

Mode request, enablement and fuel split

Adding a port rail and injectors is not enough to establish correct MPI operation. The ECU must request an appropriate combustion mode, accept that mode after its checks, calculate the desired fuel allocation and drive correctly characterised injectors. A mode request or a split value alone does not prove fuel was delivered. See the Simos Wiki fuel-management overview and EA888 Gen 3 MPI retrofit discussion; the latter is an exploratory report, not a validated recipe.

OEM mode-request examples

c_idx_cmb_mod_opp_stnd[5]: standard combustion-mode selection for an operating point in the published example. c_n_thd_mplh_opp_min[5] and c_n_thd_mplh_opp_max[5]: associated engine-speed thresholds. ip_tqi_thd_mplh_opp_min[5] and ip_tqi_thd_mplh_opp_max[5]: lower and upper indicated-torque request bounds; the example shows engine speed and coolant temperature as axes. id_idx_cmb_mod_opp_flb and id_nr_pls_cmb_mod_opp_stnd describe fallback modes and pulse counts. lv_nr_case_cmb_mod_req_opp[5] is a runtime request signal, not an editable map or proof of the final mode.

Source: TQSP torque-based combustion-mode request. Array indices and mode enumeration are example-specific.

Split and correction controls

ip_fac_opp_mpi_2_pls_1 is identified by VehiCAL's Golf R 5G0906259J 0002, SC800O3000000 example as a DI/MPI split control for its WOT MPI activation, where lower values add MPI. This is a vendor interpretation for that software and operating case: verify its definition and axes, mode availability and actual delivery before applying it elsewhere. It is not a complete MPI retrofit or universal target.

In the SC8S5031 fuel-mass model, lc_fmsp_mpi_hpdi_mod_ena enables consideration of mixed MPI/HPDI lambda variables; lc_mff_add_lam_ad_out_split_ena selects a calculation treatment for additive lambda adaptation. Neither switch proves that MPI hardware is enabled. id_maf_mpi_swi_cmb_mod selects which modes use an MPI-specific predicted-air path; it is not itself the fuel split. See homogeneous fuel-mass setpoint and basic injection mass.

fac_mff_mpi appears as a fuel-split measurement in the wall-film reference; confirm its scaling and logging support. EcuTek RaceROM exposes FlexFuel MPI DI split Normal/Warmup as a product-specific control, not an OEM engineering name; support depends on the installed RaceROM features and configuration. EcuTek flex-fuel documentation.

Inhibition and transition checks

The CBMD reference includes runtime set-inhibition signals lv_set_inh_mpi_fup_efp (feed pressure), lv_set_inh_mpi_inj_err (injector fault), and lv_set_inh_mpi_inj_lim (injection-phase limit). These are logic signals, not calibration maps; a set or clear signal should not automatically be interpreted as the final active inhibit state. Diagnose the underlying condition rather than removing safeguards.

The SC8S5031 multiple-injection correction reference lists ip_fac_mff_add_tran_mod_n_maf[3] as a fuel-mass correction factor during MPI–SDI transitions against engine speed and predicted cylinder air mass, and ip_fac_mff_add_tran_mod_tco[3] as a temperature-related transition factor against coolant temperature. These are transition corrections, not base DI/MPI fuel-split maps; verify index selection and active conditions in the target software.

Log the requested and actual mode, split, MPI and DI pulse information, fuel pressure, lambda target and measured lambda through entry, exit, warm-up and load transients. An MPI retrofit discussion reports a lean/rpm disturbance during an initial transition; this is a single exploratory case, but illustrates why stable full-load data alone is insufficient.

For starting and warm-up mode context, see cold start tuning and idle control tuning.

For flap setpoint maps, position feedback and adaptation checks, see Simos 18 intake manifold runner flap control and diagnosis.

For port-injection end-angle maps, cam correction and transient phasing, see Simos 18 MPI injection timing and phasing.

Related: Fuel system and MPI upgrades · MPI combustion modes and fuel split · MPI injector calibration · Direct injection and fuel pressure · Ethanol and flex fuel.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Simos 18 MPI combustion modes and fuel split

Applicability: Engineering names below are examples from the community SC8S5031 Simos 18.1 reference unless another source is identified. Confirm the exact ECU software, definition, units, axes, indexing and installed hardware before using a calibration; names and meanings cannot be assumed across variants. The community cross-reference can contain extraction or indexing errors. SC8S5031 reference.

Mode request, enablement and fuel split

Adding a port rail and injectors is not enough to establish correct MPI operation. The ECU must request an appropriate combustion mode, accept that mode after its checks, calculate the desired fuel allocation and drive correctly characterised injectors. A mode request or a split value alone does not prove fuel was delivered. See the Simos Wiki fuel-management overview and EA888 Gen 3 MPI retrofit discussion; the latter is an exploratory report, not a validated recipe.

OEM mode-request examples

  • c_idx_cmb_mod_opp_stnd[5]: standard combustion-mode selection for an operating point in the published example.
  • c_n_thd_mplh_opp_min[5] and c_n_thd_mplh_opp_max[5]: associated engine-speed thresholds.
  • ip_tqi_thd_mplh_opp_min[5] and ip_tqi_thd_mplh_opp_max[5]: lower and upper indicated-torque request bounds; the example shows engine speed and coolant temperature as axes.
  • id_idx_cmb_mod_opp_flb and id_nr_pls_cmb_mod_opp_stnd describe fallback modes and pulse counts. lv_nr_case_cmb_mod_req_opp[5] is a runtime request signal, not an editable map or proof of the final mode.

Source: TQSP torque-based combustion-mode request. Array indices and mode enumeration are example-specific.

Split and correction controls

ip_fac_opp_mpi_2_pls_1 is identified by VehiCAL's Golf R 5G0906259J 0002, SC800O3000000 example as a DI/MPI split control for its WOT MPI activation, where lower values add MPI. This is a vendor interpretation for that software and operating case: verify its definition and axes, mode availability and actual delivery before applying it elsewhere. It is not a complete MPI retrofit or universal target.

In the SC8S5031 fuel-mass model, lc_fmsp_mpi_hpdi_mod_ena enables consideration of mixed MPI/HPDI lambda variables; lc_mff_add_lam_ad_out_split_ena selects a calculation treatment for additive lambda adaptation. Neither switch proves that MPI hardware is enabled. id_maf_mpi_swi_cmb_mod selects which modes use an MPI-specific predicted-air path; it is not itself the fuel split. See homogeneous fuel-mass setpoint and basic injection mass.

fac_mff_mpi appears as a fuel-split measurement in the wall-film reference; confirm its scaling and logging support. EcuTek RaceROM exposes FlexFuel MPI DI split Normal/Warmup as a product-specific control, not an OEM engineering name; support depends on the installed RaceROM features and configuration. EcuTek flex-fuel documentation.

Inhibition and transition checks

The CBMD reference includes runtime set-inhibition signals lv_set_inh_mpi_fup_efp (feed pressure), lv_set_inh_mpi_inj_err (injector fault), and lv_set_inh_mpi_inj_lim (injection-phase limit). These are logic signals, not calibration maps; a set or clear signal should not automatically be interpreted as the final active inhibit state. Diagnose the underlying condition rather than removing safeguards.

The SC8S5031 multiple-injection correction reference lists ip_fac_mff_add_tran_mod_n_maf[3] as a fuel-mass correction factor during MPI–SDI transitions against engine speed and predicted cylinder air mass, and ip_fac_mff_add_tran_mod_tco[3] as a temperature-related transition factor against coolant temperature. These are transition corrections, not base DI/MPI fuel-split maps; verify index selection and active conditions in the target software.

Log the requested and actual mode, split, MPI and DI pulse information, fuel pressure, lambda target and measured lambda through entry, exit, warm-up and load transients. An MPI retrofit discussion reports a lean/rpm disturbance during an initial transition; this is a single exploratory case, but illustrates why stable full-load data alone is insufficient.

For starting and warm-up mode context, see cold start tuning and idle control tuning.

For flap setpoint maps, position feedback and adaptation checks, see Simos 18 intake manifold runner flap control and diagnosis.

Related: Fuel system and MPI upgrades · MPI combustion modes and fuel split · MPI injector calibration · Direct injection and fuel pressure · Ethanol and flex fuel.

Revision 5: Simos 18 MPI combustion modes and fuel split

Applicability: Engineering names below are examples from the community SC8S5031 Simos 18.1 reference unless another source is identified. Confirm the exact ECU software, definition, units, axes, indexing and installed hardware before using a calibration; names and meanings cannot be assumed across variants. The community cross-reference can contain extraction or indexing errors. SC8S5031 reference.

Mode request, enablement and fuel split

Adding a port rail and injectors is not enough to establish correct MPI operation. The ECU must request an appropriate combustion mode, accept that mode after its checks, calculate the desired fuel allocation and drive correctly characterised injectors. A mode request or a split value alone does not prove fuel was delivered. See the Simos Wiki fuel-management overview and EA888 Gen 3 MPI retrofit discussion; the latter is an exploratory report, not a validated recipe.

OEM mode-request examples

  • c_idx_cmb_mod_opp_stnd[5]: standard combustion-mode selection for an operating point in the published example.
  • c_n_thd_mplh_opp_min[5] and c_n_thd_mplh_opp_max[5]: associated engine-speed thresholds.
  • ip_tqi_thd_mplh_opp_min[5] and ip_tqi_thd_mplh_opp_max[5]: lower and upper indicated-torque request bounds; the example shows engine speed and coolant temperature as axes.
  • id_idx_cmb_mod_opp_flb and id_nr_pls_cmb_mod_opp_stnd describe fallback modes and pulse counts. lv_nr_case_cmb_mod_req_opp[5] is a runtime request signal, not an editable map or proof of the final mode.

Source: TQSP torque-based combustion-mode request. Array indices and mode enumeration are example-specific.

Split and correction controls

ip_fac_opp_mpi_2_pls_1 is identified by VehiCAL's Golf R 5G0906259J 0002, SC800O3000000 example as a DI/MPI split control for its WOT MPI activation, where lower values add MPI. This is a vendor interpretation for that software and operating case: verify its definition and axes, mode availability and actual delivery before applying it elsewhere. It is not a complete MPI retrofit or universal target.

In the SC8S5031 fuel-mass model, lc_fmsp_mpi_hpdi_mod_ena enables consideration of mixed MPI/HPDI lambda variables; lc_mff_add_lam_ad_out_split_ena selects a calculation treatment for additive lambda adaptation. Neither switch proves that MPI hardware is enabled. id_maf_mpi_swi_cmb_mod selects which modes use an MPI-specific predicted-air path; it is not itself the fuel split. See homogeneous fuel-mass setpoint and basic injection mass.

fac_mff_mpi appears as a fuel-split measurement in the wall-film reference; confirm its scaling and logging support. EcuTek RaceROM exposes FlexFuel MPI DI split Normal/Warmup as a product-specific control, not an OEM engineering name; support depends on the installed RaceROM features and configuration. EcuTek flex-fuel documentation.

Inhibition and transition checks

The CBMD reference includes runtime set-inhibition signals lv_set_inh_mpi_fup_efp (feed pressure), lv_set_inh_mpi_inj_err (injector fault), and lv_set_inh_mpi_inj_lim (injection-phase limit). These are logic signals, not calibration maps; a set or clear signal should not automatically be interpreted as the final active inhibit state. Diagnose the underlying condition rather than removing safeguards.

The SC8S5031 multiple-injection correction reference lists ip_fac_mff_add_tran_mod_n_maf[3] as a fuel-mass correction factor during MPI–SDI transitions against engine speed and predicted cylinder air mass, and ip_fac_mff_add_tran_mod_tco[3] as a temperature-related transition factor against coolant temperature. These are transition corrections, not base DI/MPI fuel-split maps; verify index selection and active conditions in the target software.

Log the requested and actual mode, split, MPI and DI pulse information, fuel pressure, lambda target and measured lambda through entry, exit, warm-up and load transients. An MPI retrofit discussion reports a lean/rpm disturbance during an initial transition; this is a single exploratory case, but illustrates why stable full-load data alone is insufficient.

For starting and warm-up mode context, see cold start tuning and idle control tuning.

For flap setpoint maps, position feedback and adaptation checks, see Simos 18 intake manifold runner flap control and diagnosis.

For port-injection end-angle maps, cam correction and transient phasing, see Simos 18 MPI injection timing and phasing.

Related: Fuel system and MPI upgrades · MPI combustion modes and fuel split · MPI injector calibration · Direct injection and fuel pressure · Ethanol and flex fuel.