Applicability: Volkswagen's SSP 522 describes a dual-injection EA888 CHHB/CHHA engine with Simos 18.1, in which intake-manifold injectors receive low-pressure fuel. Not every Simos 18 application has MPI hardware or the same strategy. The calibration examples below come from the community SC8S5031_C_OEM cross-reference: verify the exact ECU software, hardware, injector configuration, units, axes and active operating mode. Extracted descriptions can conflict; they do not provide universal safe values.
What injection phasing controls
Port-injection timing defines when the injector is commanded within the engine cycle. Start of injection (SOI) and end of injection (EOI) are different events; changing duration can move one event relative to the other depending on the ECU's phasing strategy and limits. At higher rpm a pulse of the same duration occupies more crank angle. Injector opening and closing dynamics also mean a commanded electrical event need not equal the hydraulic fuel event.
Fuel can enter the manifold and interact with moving air, port surfaces and the intake valve before reaching the cylinder. Cam position and operating conditions therefore matter. On Volkswagen's illustrated engine, intake-manifold injection is mainly used at part load, while the documented cold-start and full-load examples use direct injection. Different calibrations or retrofits may have other modes; a visible MPI timing map does not prove MPI is active at a given point. VW SSP 522, fuel system and modes.
Verify the angle's reference event, direction, 720-degree wrap and source definition before comparing maps or a waveform. Do not assume that a larger number means earlier or later in crank rotation, or transfer an intake-valve timing target from an unrelated software version. A map value is not necessarily the final commanded event after offsets, interpolation, transition logic and limits.
SC8S5031 base, cold and transient maps
The INJR injection-phase application reference lists these examples, with angle outputs in crankshaft degrees:
ip_eoi_bas_mpi_oppis described as the base MPI end-of-injection angle in operating-point mode, against predicted cylinder air mass for MPIm_air_cyl_pred_mpiin mg/stroke and injection speedn_injin rpm.ip_eoi_bas_mpi_opp_castis its cold-phasing example;ip_eoi_bas_mpi_opp_cast_dyn_negdescribes cold dynamic phasing during a negative load jump. Their axes are the same kinds of predicted air mass and injection speed. A similarly namedip_eoi_bas_mpi_opp_cast_dynis listed, but its description is marked uncertain; confirm its selection before naming its trigger.ip_eoi_bas_mpi_opp_dyn_negis described for a negative load jump, whileip_eoi_bas_mpi_opp_dynhas an uncertain extracted description. Neither is a general steady-state injector-size map.ip_eoi_ofs_ast_mpi_oppis an MPI after-start end-angle correction againstcyc_cast, a post-start cycle count. It is an offset, not the base angle.ip_cam_shift_mpiis an MPI-phasing camshaft shift map with intake and exhaust cam-shift inputscam_shift_inandcam_shift_ex, in crank degrees. Confirm sign, phaser references and how this value enters the final event for the target file.ip_eoi_mpi_chdescribes an MPI end-of-injection angle during catalyst heating, with predicted MPI cylinder air mass and injection-speed axes.ip_eoi_mpi_ch_sa_mpi_2_s_1is a separately named MPI–DI catalyst-heating example. The presence of either map does not establish that a particular car uses that mode.ip_ang_inj_ofs_rest_mpiis described as an MPI pulse phase offset for a transition from PUC. Its referenced axes have mg/stroke and rpm units but their inputs are markedNO_INPUT_QUANTITY; verify what PUC and those lookup inputs mean in the target implementation.
lc_eoi_1_hom_man_ena_mpi is described as a manual MPI phasing enable. Its existence is not a recommended setting or proof of the active strategy. Do not change a selector or bypass a phase constraint without establishing the complete active path.
Injection signals and diagnosis
The INJR synchronisation reference lists ti_act_swi_mpi[3] as an MPI injection-time measurement for mode-switch calculations and state_trm_mpi[3] as a transmitted MPI state. lf_inj_mpi_inh_3_cyc[2][0] and lf_inj_mpi_off_3_cyc[2][0] describe inhibit/off fields across previous, current and next cycles. They are runtime signals, not phase maps; logger support, array meaning and actual hardware configuration require verification.
Community reports describe two kinds of MPI-related disturbance. An MHH Auto tuning discussion reports transient and high-load trim behaviour after large MPI changes, with a timing-related explanation offered; this is an individual, unverified observation with multiple possible causes, not evidence of a universal injection window or a prescribed pressure or angle. An earlier MPI retrofit report describes difficult idle and uncertain lambda response in one installation. Both illustrate the need to establish injection mode, actual hardware and calibration before inferring a cause.
- Record engine, ECU software, MPI injector and rail hardware, fuel, cam setup, selected combustion mode and relevant faults. Verify injector scaling, pressure and wiring independently from phasing.
- Compare commanded and measured lambda, short- and long-term corrections, injection mode, pulse width, low-pressure fuel target and actual, engine speed, air charge and cam positions where available. Log the conditions around a transition and account for sensor transport delay.
- If the equipment and procedure support it, compare synchronised injector command and crank/cam reference signals. An electrical waveform alone does not measure delivered fuel or cylinder distribution; use injector-specific data and suitable test methods.
- Assess cold start, warm idle, part load and transients as well as the intended high-load range; a change that helps one condition can alter another. Preserve fuel, emissions and fault-monitoring functions and diagnose a pressure, injector or air leak problem before attributing the symptom to timing.
For high-pressure direct-injection SOI and EOI, see Simos 18 direct injection timing and phasing.
Related: MPI injector calibration · MPI combustion modes and fuel split · fuel trim · camshaft timing.
Sources
- Volkswagen SSP 522, fuel system and operating modes — CHHB/CHHA EA888 hardware example.
- Community SC8S5031 INJR injection-phase application reference and INJR injection synchronisation — image-specific extracted definitions with uncertain descriptions.
- MHH Auto Simos 18 tuning discussion and NefMoto enhanced port injection thread — unverified community reports, not general procedures.