Scope: The hardware description uses Volkswagen's CHHB/CHHA EA888 2.0 TSI Simos 18.1 example. Calibration identifiers below are examples from the community SC8S5031_C_OEM reference and may differ in other software. Match the engine, ECU software, hardware, definitions, units, axes and active operating mode before using them. Some extracted functional-description snippets conflict with the named field; they are leads for investigation, not a substitute for a verified definition.
Hardware and why the flap state matters
Volkswagen's SSP 522 identifies switchable intake manifold flaps, position potentiometer G336 and flap valve N316 in its illustrated CHHB/CHHA application. It says that torque- and rpm-dependent switching is stored in a map. During catalyst heating the illustrated flaps are closed, and in warm partial-load port-injection operation they remain mostly closed. That describes this engine's operating strategy, not every Simos 18 vehicle. A runner flap is separate from the electronic throttle and turbocharger wastegate.
Flap position and associated combustion and air-path models change with operating conditions. A higher-flow manifold or a fault in the flap system is not automatically a reason to force one flap state everywhere. Establish the actual hardware, operating state and feedback before changing any calibration; cold start, transient response, mixture formation and fault monitoring may be affected. Verify specific effects by measurement rather than assuming a gain.
Example setpoint maps and switching
The following are from the SC8S5031 AIRM port-flap setpoint reference. They are not addresses or universal tuning values:
id_port_sp: port-flap setpoint map. The metadata shows engine speedn_32_tmpand an mg/stroke axis referenced asldpm_maf_stk_sp_tqi_port_sp; the latter input is labelledNO_INPUT_QUANTITY, so confirm its runtime source. The scraped FR description is inconsistent with the field label.id_port_sp_chandid_port_sp_cmb_ch: catalyst-heating flap setpoint map examples. Their axes are speedn_32_tmpand air-mass setpointmaf_stk_sp_tqi_tmpin mg/stroke. The latter is described for catalyst heating outside OPP 1; verify the mode selection for the target image.id_port_sp_gearandid_port_sp_gear_opp_1_not: gear-dependent setpoint maps. Their stored axes are speed and the mg/stroke axis above; gear is part of the described selection, not an extra physical axis in these two map definitions.id_tco_port_spis described as a cold-start flap setpoint map, andid_fac_port_tcoas a setpoint correction indexed by coolant temperature.id_tco_st_port_enadescribes enabling basic setpoint determination against coolant and start-temperature thresholds.ip_maf_sp_tqi_port_hysis load hysteresis in mg/stroke against engine speed;ip_n_32_port_hysis speed hysteresis in rpm against the air-mass setpoint in mg/stroke. Hysteresis is separate from the commanded position and helps define switching behaviour.ip_map_sp_grd_port_dyn_actandip_map_sp_grd_port_dyn_deacare described as dynamic flap activation/deactivation gradient-related setpoints, with engine speed and manifold-pressure setpoint axes, pressure units hPa. The reference has conflicting copied prose; confirm the actual implementation before assigning a more precise function.
Do not infer that an individual map value universally means open or closed from a label or from a different logger. Verify the direction, selector logic and final commanded state in the matched application, especially when comparing software or manifold hardware.
Feedback, adaptation and logging
The AIRM variables reference describes state_mvb_port_sp as the commanded runner value and state_mvb_port_av as actual value. It describes fac_port_deac[0] as a feedback-derived flap position with closed = 1 for this particular quantity; this convention cannot be applied automatically to the setpoint tables or another tool. AIRM adaptation lists stored open and closed feedback voltages v_port_ad_open_1 and v_port_ad_close_1, plus the validity signal lv_port_ad_vld_1. These are measurements and adaptation results, not position maps.
COBB labels its MQB Intake Flap Set Point monitor as commanded runner-valve position; availability varies by listed vehicle and firmware. A command alone does not show that the mechanism moved. Compare it with a validated actual-position or feedback channel where available, and record speed, requested air mass, manifold pressure, temperatures, gear and active combustion mode. COBB monitor definitions.
Diagnosis and modifications
- Save codes and freeze-frame conditions, identify the precise engine and manifold, and use its current workshop procedure. Inspect connections, flap linkage, actuation and feedback before attributing a discrepancy to a map. Follow the applicable procedure for actuator testing and adaptation.
- Compare command, actual position and feedback during an appropriate supported functional test; investigate a stuck linkage, a position-sensor or wiring fault, loss of actuation, and invalid adaptation as distinct possibilities. A sustained mismatch is a diagnostic lead, not proof of one failed component.
- After repair or manifold change, apply the correct basic setting where the manufacturer specifies it, check adaptation status and confirm operation under the original conditions. Keep monitoring functional; do not suppress diagnostic codes to conceal hardware faults.
- If tuning a modified air path, confirm flap state and interaction with the air, ignition and fuelling models with repeatable logs and the correct hardware. Do not assume a replacement manifold retains the same actuation, feedback or airflow characteristic.
For context only, Volkswagen's TSB 24 15 05 labels P2014 and P2015 as runner position sensor/circuit and range/performance faults on its listed 2008–2012 CCTA/CBFA engines. Those engines and the bulletin's repair instructions are not evidence of a Simos 18 fault cause or repair applicability.
Related: air charge modelling · throttle control · MPI combustion modes · cold start · logging and diagnosis.
Sources
- Volkswagen SSP 522: 2.0 l 162/169 kW TSI engine, pages 41 and 46–48; specific EA888 hardware and modes.
- SC8S5031 community AIRM setpoint reference; calibration examples and axis metadata.
- AIRM flap variables and flap adaptation reference; image-specific feedback and learning fields.
- COBB MQB monitor list; product-specific logging terms.
- Volkswagen TSB 24 15 05; fault code descriptions for its listed older engines only.