Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 5

Removed text is struck through; added text is highlighted.

v0.3.2 board. Image: Speeduino project, reproduced with permission.

Speeduino is an open-source engine-management project with firmware, hardware designs and a community of independent builders and vendors. Official boards, their revisions and third-party implementations are not interchangeable products: establish the board, connector, controller, firmware and build before using a wiring diagram. Its official hardware designs are published under CERN-OHL-S; see the official hardware repository and getting-started manual.

Official board families

v0.1 — early stationary-test prototypev0.2 — early screw-terminal shieldv0.3 — four-channel screw-terminal shieldv0.4 — four-channel IDC shieldDropbear family: V1 and V2 eight-channel ECUsMX-5/Miata NA6 plug-inThird-party Speeduino-compatible designsThese boards use project firmware but are WTMtronics designs, not official project hardware. Consult the exact manufacturer’s documentation.WTMtronics NO2CWTMtronics UA4CWTMtronics OcelotIndividual board pages are being added below.

Wiring and commissioning

The v0.3 shield uses screw terminals, whereas the v0.4 series uses a 40-pin IDC connection plus a separate 12 V feed. Dropbear has two keyed 24-way connectors. A Mazda NA6 plug-in requires specific original harness and fuel-pump changes. Never substitute one diagram for another. Verify sensor conditioning, injector impedance, output driver type, firmware board selection and fuse arrangements against the exact board documentation before wiring.

See the hardware requirements and board layout configuration.

Country of origin is not asserted here; the project and its independent hardware ecosystem are international.

Guides and softwareBrowse the Speeduino & standalone tuning section for related guides, software and standalone ECU references.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Speeduino standalone ECUs

Speeduino is an open-source engine-management project with firmware, hardware designs and a community of independent builders and vendors. Official boards, their revisions and third-party implementations are not interchangeable products: establish the board, connector, controller, firmware and build before using a wiring diagram. Its official hardware designs are published under CERN-OHL-S; see the official hardware repository and getting-started manual.

Official board families

Individual board pages are being added below.

Wiring and commissioning

The v0.3 shield uses screw terminals, whereas the v0.4 series uses a 40-pin IDC connection plus a separate 12 V feed. Dropbear has two keyed 24-way connectors. A Mazda NA6 plug-in requires specific original harness and fuel-pump changes. Never substitute one diagram for another. Verify sensor conditioning, injector impedance, output driver type, firmware board selection and fuse arrangements against the exact board documentation before wiring.

See the hardware requirements and board layout configuration.

Country of origin is not asserted here; the project and its independent hardware ecosystem are international.

Revision 5: Speeduino standalone ECUs
Speeduino v0.3.2 shield
v0.3.2 board. Image: Speeduino project, reproduced with permission.

Speeduino is an open-source engine-management project with firmware, hardware designs and a community of independent builders and vendors. Official boards, their revisions and third-party implementations are not interchangeable products: establish the board, connector, controller, firmware and build before using a wiring diagram. Its official hardware designs are published under CERN-OHL-S; see the official hardware repository and getting-started manual.

Official board families

Third-party Speeduino-compatible designs

These boards use project firmware but are WTMtronics designs, not official project hardware. Consult the exact manufacturer’s documentation.

Wiring and commissioning

The v0.3 shield uses screw terminals, whereas the v0.4 series uses a 40-pin IDC connection plus a separate 12 V feed. Dropbear has two keyed 24-way connectors. A Mazda NA6 plug-in requires specific original harness and fuel-pump changes. Never substitute one diagram for another. Verify sensor conditioning, injector impedance, output driver type, firmware board selection and fuse arrangements against the exact board documentation before wiring.

See the hardware requirements and board layout configuration.

Country of origin is not asserted here; the project and its independent hardware ecosystem are international.

Guides and software

Browse the Speeduino & standalone tuning section for related guides, software and standalone ECU references.