Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Performance
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Tuning businesses sell upgrades in "stages", but no standard defines them. Sellers state this themselves: what a stage means varies from car to car and from tuner to tuner (Viezu), and naming runs from 1, 1+ and 2 to as high as 5 (8020 Automotive). Across sellers the broad pattern is consistent: Stage 1 is a calibration change on an otherwise standard car, Stage 2 adds bolt-on parts that help the engine breathe, and Stage 3 changes major hardware such as the turbocharger, fuel system or internals. The power gains quoted for each stage are seller claims; no independent before-and-after measurements of stage packages on production cars have been published in the sources reviewed.

What each stage commonly includes

StageTurbocharged petrolTurbodieselNaturally aspirated petrol
1Calibration only, on a healthy standard car; sometimes with an intake or an exhaust that keeps the catalystsCalibration only: fuel quantity, boost, timing, torque limitsCalibration only; little to gain without hardware
2Calibration matched to a downpipe, intake and uprated intercooler or charge cooler; sometimes a smaller supercharger pulleyCalibration matched to intercooler and exhaust changes; often a clutch able to hold the extra torqueCalibration matched to headers, intake and exhaust
3 and aboveLarger or hybrid turbocharger, injectors and fuel pump, often forged pistons and rodsHybrid or larger turbocharger, larger injectors, sometimes a higher-capacity high-pressure pumpCamshafts, porting, compression or forced induction

Higher stages also need the rest of the car to keep up: clutch, gearbox, cooling, brakes, tyres and suspension. Sellers differ on details such as whether a downpipe belongs in Stage 1 or 2, so the contents of a specific package matter more than its number. A package's parts list is compared with the supporting pages on this wiki: air (intake, exhaust, charge cooling), fuel (fuel system upgrades, pumps and lines, E85), calibration and measurement (ECU remapping, boost control, ignition tuning, lambda, data logging), and survival (pistons and rods, head gaskets and studs, cooling, oil, traction).

How far the quoted gains can be trusted

Stage 1 gains quoted by UK remapping businesses, all vendor claims:

Engine typeQuoted Stage 1 gainSellers
Naturally aspirated petrolAbout 5 to 15 % powerQuantum Tuning; Sinspeed; 8020 Automotive
Turbocharged petrolAbout 20 to 30 % powerCeltic Tuning
TurbodieselAbout 20 to 35 % torque, and claims up to 40 to 50 % powerQuantum Tuning; Celtic Tuning; Sinspeed

The sellers disagree on the size of the gains but agree on the order: turbodiesel and turbocharged petrol gain far more from calibration alone than naturally aspirated engines. That order has a clear mechanical reason. A naturally aspirated engine at full throttle is limited to roughly atmospheric manifold pressure, so a calibration can only refine fuel and ignition. On a turbocharged engine the ECU also sets boost through the wastegate or turbine vanes, and raising boost is largely a matter of calibration tables (HP Academy). Turbodiesels are commonly delivered with conservative fuel and torque limits, which is why their quoted torque gains are the largest.

No published magazine or academic before-and-after dyno test of production remap packages was found. Germany's ADAC states that the real gain can only be established by before-and-after runs on a professional dynamometer, notes that type approval already allows a ±5 % output tolerance, and warns that cheap offers often fail to deliver. The one academic study found, on a Euro 3 diesel with modified maps measured in urban traffic, recorded fuel dose up 23 % around maximum torque and 15 % near peak power, with large rises in carbon monoxide (Merkisz et al., 2020; seen in abstract only). A gain figure is therefore treated as a claim until a before-and-after measurement on the same dyno, in comparable conditions, is supplied.

Generic and bespoke files

A generic file is pre-made for a make, model and engine. It does not account for the car's condition, mileage, modifications, fuel quality or altitude. A bespoke calibration involves reading the ECU, a health check, logging, tailored changes and dyno or road verification (CSC Motors). At higher stages a generic file leaves more of the risk with the owner, because the hardware the file assumes is more likely to differ from the car. See how an ECU is remapped and common misconceptions about remapping.

UK legal and insurance points

  • Diesel particulate filters. Since February 2014, MOT testers check for a DPF; a vehicle fails if a filter fitted as standard is missing, and driving a vehicle modified that way is an offence (DfT and DVSA, 2013). Since 20 May 2018, evidence of DPF tampering and the condition of other emissions equipment, including EGR valves, oxygen and NOx sensors, are MOT test items (GOV.UK). Packages that remove or disable DPF, EGR or AdBlue systems are sometimes sold for "off-road" or motorsport use; on a road vehicle they are not lawful. DVSA has run roadside checks for AdBlue emulators on heavy goods vehicles since September 2018.
  • Insurance. The Financial Ombudsman Service upheld an insurer voiding a policy over an undeclared ECU remap and exhaust change, and advises declaring modifications even if they were made before purchase (FOS, 30 September 2024). Disclosure duties follow the Consumer Insurance (Disclosure and Representations) Act 2012.
  • Elsewhere. In Germany, ADAC notes that a power change requires approval and must be reported to the insurer. Rules differ between countries.

Questions to ask before buying

  1. What exactly does this stage contain, which parts must already be fitted, and which are assumed but not supplied?
  2. Is the file generic or built for this car, and will it be verified on a dyno or by road logs?
  3. Will a before-and-after measurement on the same dyno be provided, rather than a quoted percentage?
  4. What fuel does the calibration assume, and what happens on a lower grade?
  5. What condition checks come first: compression, leaks, boost, fuel pressure, stored faults?
  6. Which parts of the car limit at this level: clutch, tyres, cooling, brakes?
  7. Does the package keep all emissions equipment working, and will it pass an MOT?
  8. Has the modification been declared to the insurer?

All modification is at the owner's risk. What will be measured and reported is best agreed before work starts; see engine performance upgrades and planning a performance engine build.

Not established

No independent, published before-and-after measurement of stage packages on production cars was found, so the size of typical gains rests on seller claims.

Sources